Protection of Buried Utilities against Repeated Loading: Application of Geogrid-EPS Geofoam System
This article has a reply.
VIEW THE REPLYPublication: International Journal of Geomechanics
Volume 21, Issue 9
Abstract
Expanded polystyrene (EPS) geofoam is commonly used as lightweight fill materials in wide range of geotechnical engineering applications including protection of buried utilities and pipelines. EPS blocks are usually placed next to buried pipelines to reduce the overburden and traffic-induced pressure on them. In this paper, a new configuration of EPS blocks around the buried utility is defined and its performance under traffic loading examined. The proposed configuration consists of three buried EPS blocks. Two blocks (posts) are vertically oriented, while a capping EPS block (beam) is placed atop, leaving a void to protect the buried utility. Finally, soil cover is placed and compacted above the beam. By considering sufficient void space, the protection system will carry all the imposed load, and no stress will be incurred to the protected utility. The effects of beam thickness, soil cover thickness, EPS density, free span length between the posts, and soil cover reinforcement on the system's behavior under cyclic loading were explored through large-scale laboratory model tests. System performance enhanced when high-density EPS blocks, thicker beam and soil cover were used. The results also showed that reinforcing the soil cover with a single layer of geogrid could significantly lower the blocks' deformations and control their dynamic strain rate under cyclic loading. Finally, a three-dimensional finite-element model was developed, validated against experimental results, and used to gain more comprehensive insight into the protection system's performance under loading.
Get full access to this article
View all available purchase options and get full access to this article.
Notation
The following symbols are used in this paper:
- Cc
- coefficient of curvature (dimensionless);
- Cu
- coefficient of uniformity (dimensionless);
- D
- diameter of loading plate (mm);
- D10
- effective grain size (mm);
- D30
- diameter corresponding to 30% finer (mm);
- D50
- medium grain size (mm);
- D60
- diameter corresponding to 60% finer (mm);
- Eslip
- elastic slip rate (1/s);
- Gs
- specific gravity;
- hs
- soil cover thickness (mm);
- s
- loading plate settlement (mm);
- Span
- free space length between two EPS posts (mm);
- tb
- EPS beam thickness (mm);
- ΔB
- EPS beam deflection (mm); and
- φ
- internal friction angle of soil (degree).
References
AASHTO. 1990. Repetitive static plate load tests of soils and flexible pavement components for use in evaluation and design of airport and highway pavements. AASHTO T 221-90. Washington, DC: AASHTO.
AASHTO. 1993. Guide for design of pavement structures. Washington, DC: AASHTO.
Abdollahi, M., S. N. Moghaddas Tafreshi, and B. Leshchinsky. 2019. “Experimental-numerical assessment of geogrid-EPS systems for protecting buried utilities.” Geosynth. Int. 26 (4): 333–353. https://doi.org/10.1680/jgein.19.00013.
Adams, M. T., and J. G. Collin. 1997. “Large model spread footing load tests on geosynthetic reinforced soil foundations.” J. Geotech. Geoenviron. Eng. 123 (1): 66–72. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:1(66).
ASTM. 2000. Standard test method for compressive properties of rigid cellular plastics. ASTM D1621-00. West Conshohocken, PA: ASTM.
ASTM. 2009. Standard specification for graded aggregate material for bases or subbases for highways or airports. ASTM D2940/D2940M-09. West Conshohocken, PA: ASTM.
ASTM. 2011. Standard practice for classification of soils for engineering purposes (unified soil classification system). ASTM D2487-11. West Conshohocken, PA: ASTM.
ASTM. 2012. Standard test methods for laboratory compaction characteristics of soil using modified effort. ASTM D1557-12. West Conshohocken, PA: ASTM.
ASTM. 2015a. Standard test method for repetitive static plate load tests of soils and flexible pavement components, for use in evaluation and design of airport and highway pavements. ASTM D1195/D1195M-09. West Conshohocken, PA: ASTM.
ASTM. 2015b. Standard test method for density and unit weight of soil in place by sand-cone method. ASTM D1556/D1556M-15. West Conshohocken, PA: ASTM.
ASTM. 2017. Standard specification for rigid cellular polystyrene geofoam. ASTM D6817/D6817M-17. West Conshohocken, PA: ASTM.
Azizian, M., S. N. Moghaddas Tafreshi, and N. J. Darabi. 2020. “Experimental evaluation of an expanded polystyrene (EPS) block-geogrid system to protect buried pipes.” Soil Dyn. Earthquake Eng. 129: 105965. https://doi.org/10.1016/j.soildyn.2019.105965.
Bartlett, S. F., B. N. Lingwall, and J. Vaslestad. 2015. “Methods of protecting buried pipelines and culverts in transportation infrastructure using EPS geofoam.” Geotext. Geomembr. 43 (5): 450–461. https://doi.org/10.1016/j.geotexmem.2015.04.019.
Beju, Y. Z., and J. N. Mandal. 2017. “Expanded polystyrene (EPS) geofoam: Preliminary characteristic evaluation.” Procedia Eng. 189: 239–246. https://doi.org/10.1016/j.proeng.2017.05.038.
Biabani, M. M., and B. Indraratna. 2015. “An evaluation of the interface behaviour of rail sub-ballast stabilised with geogrids and geomembranes.” Geotext. Geomembr. 43 (3): 240–249. https://doi.org/10.1016/j.geotexmem.2015.04.002.
Brachman, R. W. I., I. D. Moore, and R. K. Rowe. 2000. “The design of a laboratory facility for evaluating the structural response of small-diameter buried pipes.” Can. Geotech. J. 37 (2): 281–295. https://doi.org/10.1139/t99-104.
Brito, L. A. T., A. R. Dawson, and P. J. Kolisoja. 2009. “Analytical evaluation of unbound granular layers in regard to permanent deformation.” In Proc., 8th Int. on the Bearing Capacity of Roads, Railways, and Airfields (BCR2A'09), 187–196. Champaign, IL: Univ. of Illinois at Urbana.
Chaallal, O., M. Arockiasamy, and A. Godat. 2015. “Numerical finite-element investigation of the parameters influencing the behavior of flexible pipes for culverts and storm sewers under truck load.” J. Pipeline Syst. Eng. Pract. 6 (2): 04014015. https://doi.org/10.1061/(ASCE)PS.1949-1204.0000186.
Elragi, A. F. 2000. “Selected engineering properties and applications of EPS geofoam.” Ph.D. thesis, State Univ. of New York, College of Environmental Science and Forestry Syracuse.
Elshesheny, A., M. Mohamed, and T. Sheehan. 2019a. “Buried flexible pipes behaviour in unreinforced and reinforced soils under cyclic loading.” Geosynth. Int. 26 (12): 184–205. https://doi.org/10.1680/jgein.18.00046.
Elshesheny, A., M. Mohamed, and T. Sheehan. 2019b. “Performance of buried rigid pipes under the application of incrementally increasing cyclic loading.” Soil Dyn. Earthquake Eng. 125: 105729. https://doi.org/10.1016/j.soildyn.2019.105729.
Ghotbi Siabil, S. M. A., S. N. Moghaddas Tafreshi, and A. R. Dawson. 2020. “Response of pavement foundations incorporating both geocells and expanded polystyrene (EPS) geofoam.” Geotext. Geomembr. 48 (1): 1–23. https://doi.org/10.1016/j.geotexmem.2019.103499.
Ghotbi Siabil, S. M. A., S. N. Moghaddas Tafreshi, A. R. Dawson, and M. Parvizi Omran. 2019. “Behavior of expanded polystyrene (EPS) blocks under cyclic pavement foundation loading.” Geosynth. Int. 26 (1): 1–25. https://doi.org/10.1680/jgein.18.00033.
Gonzalez-Torre, I., M. A. Calzada-Perez, A. Vega-Zamanillo, and D. Castro-Fresno. 2015. “Evaluation of reflective cracking in pavements using a new procedure that combine loads with different frequencies.” Constr. Build. Mater. 75: 368–374. https://doi.org/10.1016/j.conbuildmat.2014.11.030.
Hazarika, H. 2006. “Stress-strain modeling of EPS geofoam for large-strain applications.” Geotext. Geomembr. 24 (2): 79–90. https://doi.org/10.1016/j.geotexmem.2005.11.003.
Hegde, A. M., and T. G. Sitharam. 2015. “Experimental and numerical studies on protection of buried pipelines and underground utilities using geocells.” Geotext. Geomembr. 43 (5): 372–381. https://doi.org/10.1016/j.geotexmem.2015.04.010.
Hoff, G. C. 1967. Shock absorbing materials. Technical Rep. No. 6-763. Vicksburg, MS: U.S. Army Engineer Waterways Experiment Station.
Horvath, J. S. 1995. Geofoam geosynthetic. Scarsdale, NY: Horvath Engineering, P.C.
Horvath, J. S. 1997. “The compressible inclusion function of EPS geofoam.” Geotext. Geomembr. 15 (1–3): 77–120. https://doi.org/10.1016/S0266-1144(97)00008-3.
Kang, J., F. Parker, and C. H. Yoo. 2007. “Soil-structure interaction and imperfect trench installations for deeply buried concrete pipes.” J. Geotech. Geoenviron. Eng. 133 (3): 277–285. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:3(277).
Kim, H., B. Choi, and J. Kim. 2010. “Reduction of earth pressure on buried pipes by EPS geofoam inclusions.” Geotech. Test. J. 33 (4): 304–313. https://doi.org/doi.org/10.1520/GTJ102315.
Kumar, S. S., and S. Nagaratnam. 2013. “Load coefficient for ditch conduits covered with geosynthetic-reinforced granular backfill.” Int. J. Geomech. 13 (1): 76–82. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000181.
McAffee, R. P., and A. J. Valsangkar. 2004. “Geotechnical properties of compressible materials used for induced trench construction.” J. Test. Eval. 32 (2): 11924. https://doi.org/10.1520/JTE11924.
Meguid, M. A., M. R. Ahmed, M. G. Hussein, and Z. Omeman. 2017. “Earth pressure distribution on a rigid box covered with u-shaped geofoam wrap.” Int. J. Geosynth. Ground Eng. 3 (2): 11. https://doi.org/10.1007/s40891-017-0088-4.
Milligan, G. W. E., R. J. Fannin, and D. M. Farrar. 1986. “Model and full-scale tests of granular layers reinforced with a geogrid.” In Vol. 1 of Proc., 3rd Int. Conf. on Geotextiles, 61–66, Jupiter, FL: International Geosynthetics Society.
Moghaddas Tafreshi, S. N., N. Joz Darabi, A. R. Dawson, and M. Azizian. 2020. “Experimental evaluation of geocell and EPS geofoam as means of protecting pipes at the bottom of repeatedly loaded trenches.” Int. J. Geomech. 20 (4): 04020023. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001624.
Moghaddas Tafreshi, S. N., and O. Khalaj. 2008. “Laboratory tests of small-diameter HDPE pipes buried in reinforced sand under repeated-load.” Geotext. Geomembr. 26 (2): 145–163. https://doi.org/10.1016/j.geotexmem.2007.06.002.
Moghaddas Tafreshi, S. N., G. H. Tavakoli Mehrjardi, and A. R. Dawson. 2012. “Buried pipes in rubber-soil backfilled trenches under cyclic loading.” J. Geotech. Geoenviron. Eng. 138 (11): 1346–1356. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000710.
Oshati, O. S., A. J. Valsangkar, and A. B. Schriver. 2012. “Performance of two cast-in-place box culverts under high embankments.” Can. Geotech. J. 49 (12): 1331–1346. https://doi.org/10.1139/t2012-094.
Padade, A. H., and J. N. Mandal. 2016. “Expanded polystyrene geofoam based cellular reinforcement.” J. Test. Eval. 44 (4): 20140273. https://doi.org/10.1520/JTE20140273.
Palmeira, E. M., and L. G. S. Antunes. 2010. “Large scale tests on geosynthetic reinforced unpaved roads subjected to surface maintenance.” Geotext. Geomembr. 28 (6): 547–558. https://doi.org/10.1016/j.geotexmem.2010.03.002.
Randeniya, C. R., D. Robert, C. Q. Li, and J. Kodikara. 2020. “Large-scale experimental evaluation of soil saturation effect on behaviour of buried pipes under operational loads.” Can. Geotech. J. 57 (2): 205–220. https://doi.org/10.1139/cgj-2018-0544.
Srivastava, A., C. R. Goyal, and A. Raghuvanshi. 2013. “Load settlement response of footing placed over buried flexible pipe through a model plate load test.” Int. J. Geomech. 13 (4): 477–481. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000228.
Stark, T. D., S. F. Bartlett, and D. Arellano. 2012. Expanded polystyrene (EPS) geofoam applications and technical data. Crofton, MD: EPS Industry Alliance.
Stark, T. D., J. S. Horvath, D. Arellano, and D. Leshchinsky. 2000. Guidelines for geofoam applications in embankment projects. Interim Rep.—National Cooperative Highway Research Program Project No. 24-11. Washington, DC: Transportation Research Board, National Research Council.
Sun, L., T. C. Hopkins, and T. L. Beckham. 2009. Reduction of stresses on buried rigid highway structures using the imperfect ditch method and expanded polystyrene (Geofoam). Research Rep. No. KTC-07-14/SPR-228-01-1F. Lexington, KY: Kentucky Transportation Center, Univ. of Kentucky.
Tang, N., D. Lei, D. Huang, and R. Xiao. 2019. “Mechanical performance of polystyrene foam (EPS): Experimental and numerical analysis.” Polym. Test. 73: 359–365. https://doi.org/10.1016/j.polymertesting.2018.12.001.
Thakur, J. K., J. Han, S. K. Pokharel, and R. L. Parsons. 2012. “Performance of geocell-reinforced recycled asphalt pavement (RAP) bases over weak subgrade under cyclic plate loading.” Geotext. Geomembr. 35: 14–24. https://doi.org/10.1016/j.geotexmem.2012.06.004.
Tran, H. V., M. A. Meguid, and L. E. Chouinard. 2014. “Discrete element and experimental investigations of the earth pressure distribution on cylindrical shafts.” Int. J. Geomech. 14 (1): 80–91. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000277.
Trickey, S. A., and I. D. Moore. 2007. “Three-dimensional response of buried pipes under circular surface loading.” J. Geotech. Geoenviron. Eng. 133 (2): 219–223. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:2(219).
Witthoeft, A. F., and H. Kim. 2016. “Numerical investigation of earth pressure reduction on buried pipes using EPS geofoam compressible inclusions.” Geosynth. Int. 23 (4): 287–300. https://doi.org/10.1680/jgein.15.00054.
Wong, H., and C. J. Leo. 2006. “A simple elasto-plastic hardening constitutive model for EPS geofoam.” Geotext. Geomembr. 24 (5): 299–310. https://doi.org/10.1016/j.geotexmem.2006.03.007.
Yang, X., J. Han, S. K. Pokharel, C. Manandhar, R. L. Parsons, D. Leshchinsky, and I. Halahmi. 2012. “Accelerated pavement testing of unpaved roads with geocell-reinforced sand bases.” Geotext. Geomembr. 32: 95–103. https://doi.org/10.1016/j.geotexmem.2011.10.004.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Apr 8, 2020
Accepted: Apr 16, 2021
Published online: Jun 18, 2021
Published in print: Sep 1, 2021
Discussion open until: Nov 18, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Liping Zhu, Kejun Wen, Ruiming Tong, Mingdong Li, Dynamic Shear Strength Characteristics of Lightweight Sand-EPS Soil, Sustainability, 10.3390/su14127397, 14, 12, (7397), (2022).
- Vishnu Diyaljee, Discussion of “Protection of Buried Utilities against Repeated Loading: Application of Geogrid-EPS Geofoam System” by M. Abdollahi, S. N. Moghaddas Tafreshi, and B. Leshchinsky, International Journal of Geomechanics, 10.1061/(ASCE)GM.1943-5622.0002601, 22, 12, (2022).
- Furkan A. Akyelken, Havvanur Kılıç, Experimental and Numerical Analyses of Buried HDPE Pipe with Using EPS Geofoam, KSCE Journal of Civil Engineering, 10.1007/s12205-022-1541-z, 26, 9, (3968-3977), (2022).