New Modified Model for Estimating the Peak Shear Strength of Rock Mass Containing Nonconsecutive Joint Based on a Simulated Experiment
Publication: International Journal of Geomechanics
Volume 20, Issue 7
Abstract
In the Jennings criterion, which is commonly used to estimate the shear strength of nonconsecutive jointed rock masses, the estimated values deviate from the actual values due to the criterion failure to consider the joint undulating angle and the weakening of the mechanical properties of the rock bridge during shearing. Based on the modified Jennings criterion, this paper considers the influence of normal stress and joint continuity on the degree of weakening of the rock bridge’s mechanical parameters and presents a new correction method to further modify the Jennings criterion. The collection of undisturbed rock samples from the study area and the creation of joint(s) for laboratory testing is a cumbersome task. To overcome these limitations, a methodology to simulate the failure of jointed rock mass using the rock-like material, cement mortar, containing a single joint was adopted and its details are presented in this paper. Specifically, the direct shear tests were conducted on artificially prepared jointed rock masses with different joint continuity and undulating angles. The influence of joint continuity and the undulating angle on the shear strength of the nonconsecutive joints was studied. Then, the influence of the normal stress and joint continuity on the deterioration of the mechanical properties of the rock bridge during shearing was analyzed based on the experimental results. A new model for estimating the shear strength of a nonconsecutive jointed rock mass was proposed based on the experimental results and previous studies. The test results show that the smaller the undulating angle and the greater the penetration, the lower the shear strength of the nonconsecutive joint. Besides, the normal stress level and the joint continuity have a significant influence on the weakening of the mechanical properties of the rock bridge. When the normal stress decreases or the joint length increases, the mechanical properties of the rock bridge are significantly weakened. Compared with our estimation of the nonconsecutive joint shear strength based on the original Jennings criterion and the modified Jennings criterion, the calculation results of the newly modified Jennings criterion developed in this study are generally more consistent with the measured values, and thus, they more accurately predict the shear strength of the nonconsecutive jointed rock mass with a regular joint undulating angle.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Much of the work presented in this article was supported by the National Natural Science Foundation of China (Grant Nos. 51609129, 51479106, and 51709159); State Key Laboratory for GeoMechanics and Deep Underground Engineering, China University of Mining and Technology (Grant No. SKLGDUEK1515); Shandong Provincial Natural Science Foundation, China (Grant No. ZR2014EEQ002), Fundamental Research Funds of Shandong University (Grant No. 2015GN029); and Shandong Postdoctoral Innovation Project Special Foundation (Grant No. 201502025).
References
Bahaaddini, M., P. Hagan, R. Mitra, and B. K. Hebblewhite. 2016. “Numerical study of the mechanical behavior of nonpersistent jointed rock masses.” Int. J. Geomech. 16 (1): 04015035. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000510.
Barton, N., and V. Choubey. 1977. “The shear strength of rock joints in theory and practice.” Rock Mech. 10 (1–2): 1–54. https://doi.org/10.1007/BF01261801.
Brown, E. T. 1970. “Strength of models of rock with intermittent joints.” J. Soil. Mech. Found. Div. 96 (6): 1935–1949.
Chen, N., X. B. Zhang, Q. H. Jiang, X. Feng, W. Wei, and B. Yi. 2018a. “Shear behavior of rough rock joints reinforced by bolts.” Int. J. Geomech. 18 (1): 04017130. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001048.
Chen, X., S. Zhang, and C. Cheng. 2018b. “Numerical study on effect of joint strength mobilization on behavior of rock masses with large nonpersistent joints under uniaxial compression.” Int. J. Geomech. 18 (11): 04018140. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001260.
Ge, Y. F., H. M. Tang, M. A. M. E. Eldin, L. Wang, Q. Wu, and C. Xiong. 2017. “Evolution process of natural rock joint roughness during direct shear tests.” Int. J. Geomech. 17 (5): E4016013. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000694.
Gehle, C., and H. K. Kutter. 2003. “Breakage and shear behaviour of intermittent rock joints.” Int. J. Rock Mech. Min. Sci. 40 (5): 687–700. https://doi.org/10.1016/S1365-1609(03)00060-1.
Hencher, S. R., S. G. Lee, T. G. Carter, and L. R. Richards. 2011. “Sheeting joints: Characterisation, shear strength and engineering.” Rock Mech. Rock Eng. 44 (1): 1–22. https://doi.org/10.1007/s00603-010-0100-y.
Hencher, S. R., and L. R. Richards. 2015. “Assessing the shear strength of rock discontinuities at laboratory and field scales.” Rock Mech. Rock Eng. 48 (3): 883–905. https://doi.org/10.1007/s00603-014-0633-6.
Huang, D., D. Cen, G. Ma, and R. Huang. 2015. “Step-path failure of rock slopes with intermittent joints.” Landslides 12 (5): 911–926. https://doi.org/10.1007/s10346-014-0517-6.
Kostić, S. 2017. “Analytical models for estimation of slope stability in homogeneous intact and jointed rock masses with a single joint.” Int. J. Geomech. 17 (10): 04017089. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000994.
Lajtai, E. Z. 1969. “Strength of discontinuous rocks in direct shear.” Géotechnique 19 (2): 218–233. https://doi.org/10.1680/geot.1969.19.2.218.
Liu, Y. M., and C. C. Xia. 2006. “Study on models and strength behavior of rock mass containing discontinuous joints in direct shear.” [In Chinese.] Chinese J. Geotech. Eng. 28 (10): 1242–1247.
Liu, Y. M., and C. C. Xia. 2007. “Advances in research of rock masses containing discontinuous joints in direct shear test.” [In Chinese.] Rock Soil. Mech. 28 (8): 1719–1724.
Savilahti, T., E. Nordlund, and O. Stephansson. 1990. “Shear box testing and modeling of joint bridges.” In Proc., Int. Symp. on Rock Joints, edited by N. Barton, 295–300. Rotterdam, The Netherlands: Balkema.
Singh, K. K., D. N. Singh, and P. G. Ranjith. 2014. “Simulating flow through fractures in a rock mass using analog material.” Int. J. Geomech. 14 (1): 8–19. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000295.
Stimpson, B. 1978. “Failure of slope containing discontinuous planar joints.” In Proc., 19th U.S. Symp. on Rock Mechanics, 296–300. Reno, NV: Univ. of Nevada.
Thirukumaran, S., and B. Indraratna. 2016. “A review of shear strength models for rock joints subjected to constant normal stiffness.” J. Rock Mech. Geotech. Eng. 8 (3): 405–414. https://doi.org/10.1016/j.jrmge.2015.10.006.
Tian, H. M., W. Z. Chen, D. S. Yang, and J. P. Yang. 2015. “Experimental and numerical analysis of the shear behaviour of cemented concrete–rock joints.” Rock Mech. Rock Eng. 48 (1): 213–222. https://doi.org/10.1007/s00603-014-0560-6.
Wong, R. H. C., and K. T. Chau. 1998. “Crack coalescence in a rock-like material containing two cracks.” Int. J. Rock Mech. Min. Sci. 35 (2): 147–164. https://doi.org/10.1016/S0148-9062(97)00303-3.
Xia, C. C., W. M. Xiao, and Z. Z. Ding. 2010. “Modification of Jennings strength criterion for intermittent joints considering rock bridge weakening and joint surface undulating angle.” [In Chinese.] Chin. J. Rock Mech. Eng. 29 (3): 485–492.
Yang, X. X., P. H. S. W. Kulatilake, X. Chen, H. W. Jing, and S. Q. Yang et al. 2016. “Particle flow modeling of rock blocks with nonpersistent open joints under uniaxial compression.” Int. J. Geomech. 16 (6): 04016020. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000649.
Zeng, S., B. Jiang, and B. Sun. 2017. “Normal dynamic deformation characteristics of non-consecutive jointed rock masses under impact loads.” IOP Conf. Series: Earth Environ. Sci. 81: 012153. https://doi.org/10.1088/1755-1315/81/1/012153.
Zhang, X. B., Q. H. Jiang, P. H. S. W. Kulatilake, F. Xiong, C. Yao, Z. Tang. 2019. “Influence of asperity morphology on failure characteristics and shear strength properties of rock joints under direct shear tests.” Int. J. Geomech. 19 (2): 04018196. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001347.
Zhou, H., F. Z. Meng, C. Q. Zhang, J. Lu, and R. Xu. 2015. “Experimental study on effect of joints with different locations and sizes on rock failure.” [In Chinese.] Chin. J. Rock Mech. Eng. 34: 3018–3028. https://doi.org/10.13722/j.cnki.jrme.2014.0336.
Zhu, W. S., S. C. Li, R. H. C. Wong, K. T. Chau, and J. Xu. 2004. “A study of fracture mechanism and shear strength of rock bridges through analytical and model-testing methods.” Key Eng. Mater. 261–263: 225–230. https://doi.org/10.4028/www.scientific.net/KEM.261-263.225.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 20 • Issue 7 • July 2020
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Jun 13, 2019
Accepted: Jan 29, 2020
Published online: Apr 22, 2020
Published in print: Jul 1, 2020
Discussion open until: Sep 22, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.