Calculating the State Parameter in Crushable Sands
Publication: International Journal of Geomechanics
Volume 20, Issue 7
Abstract
The state parameter (ψ) measures the distance from the current state to the critical state line (CSL) in the compression plane. The existence of a correlation between both the peak angle of shearing resistance and peak dilatancy and ψ is central to many constitutive models used to predict granular soil behavior. These correlations do not explicitly consider particle crushing. Crushing-induced evolution of the particle size distribution influences the CSL position, and recent research supports the use of a critical state plane (CSP) to account for changes in grading. This contribution evaluates whether the CSP can be used to calculate ψ and thus enable the prediction of the peak angle of and peak dilatancy where crushing takes place. The data considered were generated from a validated DEM model of Fontainebleau sand that considers particle crushing. It is shown that where ψ is calculated by considering the CSL of the original uncrushed material, there can be a significant error in predicting the material response. However, where the CSP is used, there is a significant improvement in our ability to predict behavior irrespective of whether the CSP is accurately determined using a large number of tests or approximated using crushing yield envelopes. It is shown that the state parameter calculated using the previously available definition can give a false sense of security when assessing the liquefaction potential of potentially crushable soils. This contribution also highlights the stress-path dependency of the relationship between and ψ whichever approach is used to determine ψ.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
A part of this research was supported by the first Author's Junior Research Fellowship at Imperial College London.
Notation
The following symbols are used in this paper:
- dilatancy at the point where the peak stress ratio is mobilized;
- e
- void ratio;
- void ratio on CSL;
- initial void ratio;
- I G
- grading state index following Muir Wood and Maeda (2008);
- I G,0
- grading state index based on initial grading;
- p′
- mean effective stress;
- rate of change of mean effective stress with respect to time;
- mean effective stress at the critical state;
- q
- deviator stress;
- η
- stress obliquity, q/p′;
- ψ
- state parameter;
- state parameter as the distance to CSL from the initial stress and the void ratio;
- within multiple CSLs, state parameter as the distance to the corresponding CSL from the initial stress and the void ratio;
- state parameter as the distance to CSP from the initial stress, the void ratio, and IG ;
- state parameter as the distance to CSP from the initial stress, the void ratio, and the measured IG at CS;
- state parameter as the distance to CSP from the initial stress, the void ratio, and the predicted IG at CS;
- rate of change of radial effective stress with respect to time;
- rate of change of vertical effective stress with respect to time;
- critical state angle of shearing resistance; and
- peak angle of shearing resistance.
References
Altuhafi, F. N., R. J. Jardine, V. N. Georgiannou, W. W. Moinet, M. O. Ciantia, M. Arroyo, and A. Gens. 2018. “ Effects of particle breakage and stress reversal on the behaviour of sand around displacement piles.” Géotechnique 68 ( 6 ): 546 – 555. https://doi.org/10.1680/jgeot.17.P.117.
Azeiteiro, R. J. N., P. A. L. F. Coelho, D. M. G. Taborda, and J. C. D. Grazina. 2017. “ Critical state-based interpretation of the monotonic behavior of Hostun sand.” J. Geotech. Geoenviron. Eng 143 ( 5 ): 04017004. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001659.
Bandini, V., and M. R. Coop. 2011. “ The influence of particle breakage on the location of the critical state line of sands.” Soils Found. 51 ( 4 ): 591 – 600. https://doi.org/10.3208/sandf.51.591.
Been, K., and M. G. Jefferies. 1985. “ A state parameter for sands.” Géotechnique 35 ( 2 ): 99 – 112. https://doi.org/10.1680/geot.1985.35.2.99.
Been, K., M. G. Jefferies, and J. Hachey. 1991. “ The critical state of sands.” Géotechnique 41 ( 3 ): 365 – 381. https://doi.org/10.1680/geot.1991.41.3.365.
Bishop, A. W. 1973. “ The stability of tips and spoil heaps.” Q. J. Eng. Geol. Hydrogeol. 6 ( 3–4 ): 335 – 376. https://doi.org/10.1144/GSL.QJEG.1973.006.03.15.
Ciantia, M. O., M. Arroyo, J. Butlanska, and A. Gens. 2016. “ DEM modelling of cone penetration tests in a double-porosity crushable granular material.” Comput. Geotech. 73 : 109 – 127. https://doi.org/10.1016/j.compgeo.2015.12.001.
Ciantia, M. O., M. Arroyo, F. Calvetti, and A. Gens. 2015. “ An approach to enhance efficiency of DEM modelling of soils with crushable grains.” Géotechnique 65 ( 2 ): 91 – 110. https://doi.org/10.1680/geot.13.P.218.
Ciantia, M. O., M. Arroyo, C. O’Sullivan, A. Gens, and T. Liu. 2019a. “ Grading evolution and critical state in a discrete numerical model of Fontainebleau sand.” Géotechnique 69 ( 1 ): 1 – 15. https://doi.org/10.1680/jgeot.17.P.023.
Ciantia, M. O., C. O’Sullivan, M. Arroyo, and A. Gens. 2019b. “ Breakage and critical state via DEM.” In Proc., 17th European Conf. on Soil Mechanics and Geotechnical Engineering. 1 – 8. Reykjavík, Iceland : ISSMGE.
Ciantia, M. O., C. O’Sullivan, and R. J. Jardine. 2019c. “ Pile penetration in crushable soils: Insights from micromechanical modelling.” In Proc., 17th European Conf. on Soil Mechanics and Geotechnical Engineering, Reykjavík, Iceland., 298 – 317.
Coop, M. R. 1990. “ The mechanics of uncemented carbonate sands.” Géotechnique 40 ( 4 ): 607 – 626. https://doi.org/10.1680/geot.1990.40.4.607.
Coop, M. R., and I. K. Lee. 1993. “ The behaviour of granular soils at elevated stresses.” In Predictive soil mechanics, edited by G. T. Houlsby, P. Wroth, and A. N. Schofield, 186 – 198. London : Thomas Telford.
Gens, A. 2019. “ Hydraulic fills with special focus on liquefaction remblais hydrauliques en dédiant une attention particulière à la liquéfaction.” In Proc., 17th European Conf. on Soil Mechanics and Geotechnical Engineering, 52 – 82. Reykjavík, Iceland : ISSMGE.
Ghafghazi, M., D. A. Shuttle, and J. T. DeJong. 2014. “ Particle breakage and the critical state of sand.” Soils Found. 54 ( 3 ): 451 – 461. https://doi.org/10.1016/j.sandf.2014.04.016.
Hyodo, M., A. F. L. Hyde, and N. Aramaki. 1998. “ Liquefaction of crushable soils.” Géotechnique 48 ( 4 ): 527 – 543. https://doi.org/10.1680/geot.1998.48.4.527.
Jefferies, M., and K. Been. 2006. Soil liquefaction: A critical state approach. London : Taylor and Francis.
Jovicic, V., and M. R. Coop. 1997. “ Stiffness of coarse-grained soils at small strains.” Géotechnique 47 ( 3 ): 545 – 561. https://doi.org/10.1680/geot.1997.47.3.545.
Kikumoto, M., D. M. Wood, and A. Russell. 2010. “ Particle crushing and deformation behaviour.” Soils Found. 50 ( 4 ): 547 – 563. https://doi.org/10.3208/sandf.50.547.
Klotz, E. U., and M. R. Coop. 2001. “ An investigation of the effect of soil state on the capacity of driven piles in sands.” Géotechnique 51 ( 9 ): 733 – 751. https://doi.org/10.1680/geot.2001.51.9.733.
Lee, K. L., and I. Farhoomand. 1967. “ Compressibility and crushing of granular soil in anisotropic triaxial compression.” Can. Geotech. J. 4 ( 1 ): 68 – 86. https://doi.org/10.1139/t67-012.
Leleu, S. L., and J. R. Valdes. 2007. “ Experimental study of the influence of mineral composition on sand crushing.” Géotechnique 57 ( 3 ): 313 – 317. https://doi.org/10.1680/geot.2007.57.3.313.
Luong, M. P., and A. Tuati. 1983. “ Sols grenus sous fortes contraintes.” Rev. Fr. Geotech. 24 : 51 – 63. https://doi.org/10.1051/geotech/1983024051.
McDowell, G. R., and M. D. Bolton. 1998. “ On the micromechanics of crushable aggregates.” Géotechnique 48 ( 5 ): 667 – 679. https://doi.org/10.1680/geot.1998.48.5.667.
Muir Wood, D., and K. Maeda. 2008. “ Changing grading of soil: Effect on critical states.” Acta Geotech. 3 ( 1 ): 3 – 14. https://doi.org/10.1007/s11440-007-0041-0.
Robertson, P. K. 2017. “ Evaluation of flow liquefaction: Influence of high stresses.” In Proc., 3rd Int. Conf. on Performance Based Design (PBD-III), Vancouver : ISSMGE.
Sadrekarimi, A., and S. Olson. 2014. “ Trace metal leaching from embankment soils amended with high-carbon fly ash.” J. Geotech. Geoenviron. Eng. 140 ( 1 ): 1 – 13. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000996.
Wroth, C. P., and R. H. Bassett. 1965. “ A stress–strain relationship for the shearing behaviour of a sand.” Géotechnique 15 ( 1 ): 32 – 56. https://doi.org/10.1680/geot.1965.15.1.32.
Xiao, Y., and H. Liu. 2017. “ Elastoplastic constitutive model for rockfill materials considering particle breakage.” Int. J. Geomech. 17 ( 1 ): 04016041. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000681.
Xiao, Y., H. Liu, X. Ding, Y. Chen, J. Jiang, and W. Zhang. 2016. “ Influence of particle breakage on critical state line of rockfill material.” Int. J. Geomech. 16 ( 1 ): 04015031. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000538.
Xiao, Y., M. Meng, A. Daouadji, Q. Chen, Z. Wu, and X. Jiang. 2018. “ Effects of particle size on crushing and deformation behaviors of rockfill materials.” Geosci. Front. https://doi.org/10.1016/j.gsf.2018.10.010.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: May 13, 2019
Accepted: Dec 17, 2019
Published online: Apr 22, 2020
Published in print: Jul 1, 2020
Discussion open until: Sep 22, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.