Analytical and Experimental Study of Cemented Backfill and Pillar Interactions
Publication: International Journal of Geomechanics
Volume 19, Issue 8
Abstract
Massive voids form in underground mines due to the continuous removal of valuable minerals. Backfill and pillars are commonly built into the voids to provide both local and regional support. The backfill material cannot rigidly support the upper load and acts as a secondary support system to the pillars. Confinement effect effectively enhances the strength of the pillar; however, the lateral stress mobilized within the fill is contingent upon deformation of the roof and pillars, which act as a passive support. Without large-scale volumetric compression, the backfill has no effect on the prepeak stage of the pillar. In this case, the friction resistance of the interface between the pillar and backfill plays a key role in increasing the load capacity of the support system. This paper presents an analytical solution based on the load transfer of friction force in the interface, which involves the shear behavior of the interface, the mechanical properties of the pillar, and the pillar dimensions. Experimental results showed that the bearing capacity of the support system was strongly dependent on the interface shear parameters, lateral stress, and fill ratio. Comparisons were made between the proposed solution and experimental results. The results may represent a workable understanding of the interaction mechanism between backfill and pillars and assist in the design and optimization of underground mine support systems.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work is funded by the National Key Research and Development Program of China (Grant 2016YFC0801607), National Science Foundation of China (Grants 51525402, 51874069, and 51761135102), and the Fundamental Research Funds for the Central Universities of China (Grants N180115009 and N170106003). These supports are gratefully acknowledged.
References
Blight, G. E., and I. E. Clarke. 1983. “Design and properties of stiff fill for lateral support of pillars.” Int. J. Rock Mech. Min. 22 (3): 303–307.
Cheng, G., T. Ma, C. Tang, H. Liu, and S. Wang. 2017. “A zoning model for coal mining–induced strata movement based on microseismic monitoring.” Int. J. Rock Mech. Min. 94: 123–138. https://doi.org/10.1016/j.ijrmms.2017.03.001.
Choudhary, B. S., and S. Kumar. 2013. “Underground void filling by cemented mill tailings.” Int. J. Min. Sci. Technol. 23 (6): 893–900. https://doi.org/10.1016/j.ijmst.2013.11.003.
Coyle, H. M., and L. C. Reese. 1966. “Load transfer for axially loaded piles in clay.” J. Soil. Mech. Found. Div. 92: 1–26.
Donovan, J. G., and M. G. Karfakis. 2004. “Design of backfilled thin-seam coal pillars using earth pressure theory.” Geotech. Geol. Eng. 22 (4): 627–642. https://doi.org/10.1023/B:GEGE.0000047047.65476.c6.
Esterhuizen, G. S., D. R. Dolinar, and J. L. Ellenberger. 2011. “Pillar strength in underground stone mines in the United States.” Int. J. Rock Mech. Min. 48 (1): 42–50. https://doi.org/10.1016/j.ijrmms.2010.06.003.
Falaknaz, N., M. Aubertin, and L. Li. 2015. “Numerical analyses of the stress state in two neighboring stopes excavated and backfilled in sequence.” Int. J. Geomech. 15 (6): 04015005. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000466.
Fall, M., and O. Nasir. 2010. “Mechanical behaviour of the interface between cemented tailings backfill and retaining structures under shear loads.” Geotech. Geol. Eng. 28 (6): 779–790. https://doi.org/10.1007/s10706-010-9338-0.
Galvin, B. J. M. 2016. Ground engineering—Principles and practices for underground coal mining. New York: Springer.
Ghasemi, E., M. Ataei, K. Shahriar, F. Sereshki, S. E. Jalali, and A. Ramazanzadeh. 2012. “Assessment of roof fall risk during retreat mining in room and pillar coal mines.” Int. J. Rock Mech. Min. 54: 80–89. https://doi.org/10.1016/j.ijrmms.2012.05.025.
Ghirian, A., and M. Fall. 2014. “Coupled thermo-hydro-mechanical–chemical behaviour of cemented paste backfill in column experiments.” Eng. Geol. 170: 11–23. https://doi.org/10.1016/j.enggeo.2013.12.004.
Gokhale, A. M., and E. E. Underwood. 1990. “A general method for estimation of fracture surface roughness: Part I. Theoretical aspects.” Metall. Trans. A 21 (5): 1193–1199. https://doi.org/10.1007/BF02698249.
Helinski, M., A. Fourie, M. Fahey, and M. Ismail. 2007. “Assessment of the self-desiccation process in cemented mine backfills.” Can. Geotech. J. 44 (10): 1148–1156. https://doi.org/10.1139/T07-051.
Hou, C., W. Zhu, B. Yan, K. Guan, and J. Du. 2018. “Influence of binder content on temperature and internal strain evolution of early age cemented tailings backfill.” Constr. Build. Mater. 189: 585–593. https://doi.org/10.1016/j.conbuildmat.2018.09.032.
Hustrulid, W. A. 2004. Underground mining methods. Engineering fundamentals and international case studies. Littleton, CO: Society for Mining Metallurgy & Exploration.
Jiang, Y., W. Hongwei, Z. Yixin, Z. Jie, and P. Xufeng. 2011. “The influence of roadway backfill on bursting liability and strength of coal pillar by numerical investigation.” Procedia. Eng. 26: 1125–1143. https://doi.org/10.1016/j.proeng.2011.11.2283.
Kesimal, A., B. Ercikdi, and E. Yilmaz. 2003. “The effect of desliming by sedimentation on paste backfill performance.” Miner. Eng. 16 (10): 1009–1011. https://doi.org/10.1016/S0892-6875(03)00267-X.
Kesimal, A., E. Yilmaz, B. Ercikdi, I. Alp, and H. Deveci. 2005. “Effect of properties of tailings and binder on the short-and long-term strength and stability of cemented paste backfill.” Mater. Lett. 59 (28): 3703–3709. https://doi.org/10.1016/j.matlet.2005.06.042.
Kim, H. J., and J. L. C. Mission. 2009. “Negative skin friction on piles based on finite strain consolidation theory and the nonlinear load transfer method.” KSCE J. Civ. Eng. 13 (2): 107–115. https://doi.org/10.1007/s12205-009-0107-7.
Kim, S., S. Jeong, S. Cho, and I. Park. 1999. “Shear load transfer characteristics of drilled shafts in weathered rocks.” J. Geotech. Geoenviron. Eng. 125 (11): 999–1010. https://doi.org/10.1061/(ASCE)1090-0241(1999)125:11(999).
Kostecki, T., and A. J. S. Spearing. 2015. “Influence of backfill on coal pillar strength and floor bearing capacity in weak floor conditions in the Illinois Basin.” Int. J. Rock Mech. Min. 76: 55–67. https://doi.org/10.1016/j.ijrmms.2014.11.011.
Koupouli, N. J. F., T. Belem, P. Rivard, and H. Effenguet. 2016. “Direct shear tests on cemented paste backfill–rock wall and cemented paste backfill–backfill interfaces.” J. Rock Mech. Geotech. Eng. 8 (4): 472–479. https://doi.org/10.1016/j.jrmge.2016.02.001.
Lee, S.-K., Y.-C. Song, and S.-H. Han. 2004. “Biaxial behavior of plain concrete of nuclear containment building.” Nucl. Eng. Des. 227 (2): 143–153. https://doi.org/10.1016/j.nucengdes.2003.09.001.
Li, L., and M. Aubertin. 2008. “An improved analytical solution to estimate the stress state in subvertical backfilled stopes.” Can. Geotech. J. 45 (10): 1487–1496. https://doi.org/10.1139/T08-060.
Li, L., and M. Aubertin. 2009a. “Numerical investigation of the stress state in inclined backfilled stopes.” Int. J. Geomech. 9 (2): 52–62. https://doi.org/10.1061/(ASCE)1532-3641(2009)9:2(52).
Li, L., and M. Aubertin. 2009b. “A three-dimensional analysis of the total and effective stresses in submerged backfilled stopes.” Geotech. Geol. Eng. 27 (4): 559–569. https://doi.org/10.1007/s10706-009-9257-0.
Li, L., and M. Aubertin. 2014. “An improved method to assess the required strength of cemented backfill in underground stopes with an open face.” Int. J. Min. Sci. Technol. 24 (4): 549–558. https://doi.org/10.1016/j.ijmst.2014.05.020.
Manaras, S. 2009. “Investigations of backfill-rock mass interface failure mechanisms.” M.S. thesis, Queen’s Univ.
Marston, A. 1930. “The theory of external loads on closed conduits in the light of the latest experiments.” Highway Res. Board Proc. 9: 138–170.
Mo, S., I. Canbulat, C. Zhang, J. Oh, B. Shen, and P. Hagan. 2018. “Numerical investigation into the effect of backfilling on coal pillar strength in highwall mining.” Int. J. Min. Sci. Technol. 28 (2): 281–286. https://doi.org/10.1016/j.ijmst.2017.07.003.
Moradian, Z. A., G. Ballivy, and P. Rivard. 2012. “Application of acoustic emission for monitoring shear behavior of bonded concrete–rock joints under direct shear test.” Can. J. Civ. Eng. 39 (8): 887–896. https://doi.org/10.1139/l2012-073.
Nasir, O., and M. Fall. 2008. “Shear behaviour of cemented pastefill-rock interfaces.” Eng. Geol. 101 (3–4): 146–153. https://doi.org/10.1016/j.enggeo.2008.04.010.
Patton, F. D. 1966. “Multiple modes of shear failure in rock.” In Vol. 1 of Proc., 1st Congress of Int. Society Rock Mechanics, 509–13. Lisbon, Portugal: Laboratório Nacional de Engenharia Civil.
Saiang, D., L. Malmgren, and E. Nordlund. 2005. “Laboratory tests on shotcrete-rock joints in direct shear, tension and compression.” Rock Mech. Rock Eng. 38 (4): 275–297. https://doi.org/10.1007/s00603-005-0055-6.
Salamon, M. D. G., and K. L. Oravecz 1976. Rock Mechanics in Coal Mining. PRD Series 198, 59–65. Johannesburg, South Africa: Chamber of Mines of South Africa.
Seidel, J. P., and B. Collingwood. 2001. “A new socket roughness factor for prediction of rock socket shaft resistance.” Can. Geotech. J. 38 (1): 138–153. https://doi.org/10.1139/t00-083.
Seol, H., S. Jeong, and Y. Kim. 2009. “Load transfer analysis of rock-socketed drilled shafts by coupled soil resistance.” Comput. Geotech. 36 (3): 446–453. https://doi.org/10.1016/j.compgeo.2008.08.012.
Sinnathamby, G., L. Korkiala-Tanttu, and J. Gallardo Forés. 2014. “Interface shear behaviour of tunnel backfill materials in a deep-rock nuclear waste repository in Finland.” Soils Found. 54 (4): 777–788. https://doi.org/10.1016/j.sandf.2014.06.027.
Sinnathamby, G., L. Korkiala-Tanttu, and L. T. Salvador. 2015. “Shear resistance of bentonite backfill materials and their interfaces under varying hydraulic conditions in a deep rock nuclear waste repository.” Appl. Clay Sci. 104: 211–220. https://doi.org/10.1016/j.clay.2014.11.035.
Sivakugan, N., R. M. Rankine, K. J. Rankine, and K. S. Rankine. 2006. “Geotechnical considerations in mine backfilling in Australia.” J. Cleaner Prod. 14 (12–13): 1168–1175. https://doi.org/10.1016/j.jclepro.2004.06.007.
Tesarik, D. R., J. B. Seymour, and T. R. Yanske. 2003. “Post-failure behavior of two mine pillars confined with backfill.” Int. J. Rock Mech. Min. 40 (2): 221–232. https://doi.org/10.1016/S1365-1609(02)00139-9.
Tesarik, D. R., J. B. Seymour, and T. R. Yanske. 2009. “Long-term stability of a backfilled room-and-pillar test section at the Buick Mine, Missouri, USA.” Int. J. Rock Mech. Min. 46 (7): 1182–1196. https://doi.org/10.1016/j.ijrmms.2008.11.010.
Tian, H. M., W. Z. Chen, D. S. Yang, and J. P. Yang. 2015. “Experimental and numerical analysis of the shear behaviour of cemented concrete–rock joints.” Rock Mech. Rock Eng. 48 (1): 213–222. https://doi.org/10.1007/s00603-014-0560-6.
Tiwari, R. P., and K. S. Rao. 2006. “Post failure behaviour of a rock mass under the influence of triaxial and true triaxial confinement.” Eng. Geol. 84 (3–4): 112–129. https://doi.org/10.1016/j.enggeo.2006.01.001.
Wang, H., B. A. Poulsen, B. Shen, S. Xue, and Y. Jiang. 2011. “The influence of roadway backfill on the coal pillar strength by numericalinvestigation.” Int. J. Rock Mech. Min. 48 (3): 443–450. https://doi.org/10.1016/j.ijrmms.2010.09.007.
Williams, T. J., T. M. Brady, D. C. Bayer, M. J. Bren, R. T. Pakalnis, J. A. Marjerison, and R. B. Langston. 2007. “Underhand cut and fill mining as practiced in three deep hard rock mines in the United States.” In Proc., CIM Conf. and Exhibition. Westmount, QC, Canada: Canadian Institute of Mining, Metallurgy and Petroleum.
Yang, L., E. Yilmaz, J. Li, H. Liu, and H. Jiang. 2018. “Effect of superplasticizer type and dosage on fluidity and strength behavior of cemented tailings backfill with different solid contents.” Constr. Build. Mater. 187: 290–298. https://doi.org/10.1016/j.conbuildmat.2018.07.155.
Yang, P., L. Li, and M. Aubertin. 2017. “A new solution to assess the required strength of mine backfill with a vertical exposure.” Int. J. Geomech. 17 (10): 04017084. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000975.
Zhang, C., X.-T. Feng, H. Zhou, S. Qiu, and W. Wu. 2012. “Case histories of four extremely intense rockbursts in deep tunnels.” Rock Mech. Rock Eng. 45 (3): 275–288. https://doi.org/10.1007/s00603-011-0218-6.
Zhang, Q.-Q., Z.-M. Zhang, and J.-Y. He. 2010. “A simplified approach for settlement analysis of single pile and pile groups considering interaction between identical piles in multilayered soils.” Comput. Geotech. 37 (7–8): 969–976. https://doi.org/10.1016/j.compgeo.2010.08.003.
Information & Authors
Information
Published In
Copyright
© 2019 American Society of Civil Engineers.
History
Received: May 17, 2018
Accepted: Jan 3, 2019
Published online: May 16, 2019
Published in print: Aug 1, 2019
Discussion open until: Oct 16, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.