Three-Dimensional Simulations of Plate Anchor Pullout in Granular Materials
Publication: International Journal of Geomechanics
Volume 19, Issue 4
Abstract
Plate anchors are embedded into the ocean floor to provide holding capacity for offshore structures. Anchor holding capacity is a function of both the anchor and soil properties. Although plate anchors have been widely studied experimentally and numerically, there is still no universally agreed-upon design approach, indicating that the problem physics remain elusive. In this work, discrete-element method (DEM) simulations were used to investigate the behavior of plate anchors during pullout in an effort to elucidate some of the microscale physical processes that influence overall system behavior. Macroscale assembly response was compared to published experimental results and empirical solutions. The influence of embedment ratio, anchor roughness, soil density, and anchor size on holding capacity was investigated, and system-scale results reasonably agreed with previously published work. Thus, observations of the simulated contact force network and particle velocity during uplift were used to provide insight into anchor failure mechanisms. Finally, the model was used to briefly explore the response of a cyclically loaded plate anchor embedded in a granular assembly.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This material is based upon work supported by the Department of Energy under Award DE-FG36-08GO18179. This paper was prepared as an account of work sponsored by an agency of the United States Government. Neither the United States Government nor any agency thereof, nor any of their employees, makes any warranty, expressed or implied, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. The views and opinions of the authors expressed herein do not necessarily state or reflect those of the United States Government or any agency thereof.
References
Athani, S., P. Kharel, D. Airey, and P. Rognon. 2017. “Grain-size effect on uplift capacity of plate anchors in coarse granular soils.” Géotechnique Lett. 7 (2): 167–173. https://doi.org/10.1680/jgele.17.00002.
Balla, A. 1961. “The resistance to breaking out of mushroom foundations for pylons.” In Proc., 5th Int. Conf. on Soil Mechanics and Foundation Engineering, 569–576. Paris: Dunod.
Basudhar, P. K., and D. N. Singh. 1994. “A generalized procedure for predicting optimal lower bound break-out factors of strip anchors.” Géotechnique 44 (2): 307–318. https://doi.org/10.1680/geot.1994.44.2.307.
Belheine, N., J. P. Plassiard, F.-V. Donzé, F. Darve, and A. Seridi. 2009. “Numerical simulation of drained triaxial test using 3-D discrete element modeling.” Comput. Geotech. 36 (1–2): 320–331. https://doi.org/10.1016/j.compgeo.2008.02.003.
Chattopadhyay, B. C., and P. J. Pise. 1986. “Breakout resistance of horizontal anchors in sand.” Soils Found. 26 (4): 16–22. https://doi.org/10.3208/sandf1972.26.4_16.
Chow, S. H., C. D. O'Loughlin, R. Corti, C. Gaudin, and A. Diambra. 2015. “Drained cyclic capacity of plate anchors in dense sand: Experimental and theoretical observations.” Géotechnique Lett. 5 (2): 80–85. https://doi.org/10.1680/geolett.15.00019.
Cundall, P. A., and O. D. L. Strack. 1979. “A discrete numerical model for granular assemblies.” Géotechnique 29 (1): 47–65. https://doi.org/10.1680/geot.1979.29.1.47.
Das, B. M., and G. R. Seeley. 1975. “Breakout resistance of shallow horizontal anchors.” J. Geotech. Eng. Div. 101 (9): 999–1003.
Das, B. M., E. C. Shin, R. N. Dass, and M. T. Omar. 1994. “Suction force below plate anchors in soft clay.” Mar. Georesour. Geotechnol. 12 (1): 71–81. https://doi.org/10.1080/10641199409388255.
Dickin, E. A. 1988. “Uplift behavior of horizontal anchor plates in sand.” J. Geotech. Eng. 114 (11): 1300–1317. https://doi.org/10.1061/(ASCE)0733-9410(1988)114:11(1300).
Dickin, E. A., and M. Laman. 2007. “Uplift response of strip anchors in cohesionless soil.” Adv. Eng. Software 38 (8–9): 618–625. https://doi.org/10.1016/j.advengsoft.2006.08.041.
Dyson, A. S., and P. G. Rognon. 2014. “Pull-out capacity of tree root inspired anchors in shallow granular soils.” Géotechnique Lett. 4 (4): 301–305. https://doi.org/10.1680/geolett.14.00061.
Evans, T. M., and J. D. Frost. 2010. “Multiscale investigation of shear bands in sand: Physical and numerical experiments.” Int. J. Numer. Anal. Methods Geomech. 34 (15): 1634–1650.
Evans, T. M., and J. G. Kress. 2011. “Discrete simulations of particulate-structure interactions.” In GeoFrontiers 2011: Advances in Geotechnical Engineering, Geotechnical Special Publication 211, 4252–4262. Reston, VA: Geo-Institute.
Evans, T. M., and J. R. Valdes. 2011. “The microstructure of particulate mixtures in one-dimensional compression: Numerical studies.” Granular Matter 13 (5): 657–669. https://doi.org/10.1007/s10035-011-0278-z.
Frost, J. D., J. T. DeJong, and M. Recalde. 2002. “Shear failure behavior of granular–continuum interfaces.” Eng. Fract. Mech. 69 (17): 2029–2048. https://doi.org/10.1016/S0013-7944(02)00075-9.
Frost, J. D., G. Hebeler, T. M. Evans, and J. DeJong. 2004. “Interface behavior of granular soils.” In Proc., Engineering, Construction, and Operations in Challenging Environments, 65–72. Reston, VA: ASCE.
Frydman, S., and I. Shaham. 1989. “Pullout capacity of slab anchors in sand.” Can. Geotech. J. 26 (3): 385–400. https://doi.org/10.1139/t89-053.
Gao, G., and M. A. Meguid. 2018. “On the role of sphericity of falling rock clusters—Insights from experimental and numerical investigations.” Landslides 15 (2): 219–232. https://doi.org/10.1007/s10346-017-0874-z.
Gaudin, C., C. D. O'Loughlin, M. F. Randolph, and A. C. Lowmass. 2006. “Influence of the installation process on the performance of suction embedded plate anchors.” Géotechnique 56 (6): 381–391. https://doi.org/10.1680/geot.2006.56.6.381.
Holtz, R. D., W. D. Kovacs, and T. C. Sheahan. 2011. An introduction to geotechnical engineering. 2nd ed. Upper Saddle River, NJ: Prentice Hall.
Ilamparuthi, K., E. A. Dickin, and K. Muthukrisnaiah. 2002. “Experimental investigation of the uplift behaviour of circular plate anchors embedded in sand.” Can. Geotech. J. 39 (3): 648–664. https://doi.org/10.1139/t02-005.
Itasca Consulting Group. 2008. PFC3D: Particle flow code in three dimensions v4.0. Minneapolis: Itasca Consulting Group.
Khadilkar, B. S., A. K. Paradkar, and Y. S. Golait. 1971. “Study of rupture surface and ultimate resistance of anchor foundations.” In Vol. 1 of Proc., 4th Asian Regional Conf. on Soil Mechanics and Foundation Engineering, 121–127. Bangkok, Thailand: AIT.
Kress, J. G., and T. M. Evans. 2010. “Analysis of pile behavior in granular soils using DEM.” In Proc., 35th Annual Deep Foundations Institute Annual Conf. Hawthorne, NJ: Deep Foundations Institute.
Kumar, J., and K. M. Kouzer. 2008a. “Vertical uplift capacity of a group of shallow horizontal anchors in sand.” Géotechnique 58 (10): 821–823. https://doi.org/10.1680/geot.2008.58.10.821.
Kumar, J., and K. M. Kouzer. 2008b. “Vertical uplift capacity of horizontal anchors using upper bound limit analysis and finite elements.” Can. Geotech. J. 45 (5): 698–704. https://doi.org/10.1139/T08-005.
Lesny, K., and P. Hinz. 2009. “Design of monopile foundations for offshore wind energy converters.” In Contemporary topics in deep foundations, 512–519. Reston, VA: ASCE.
Liu, J., M. Liu, and Z. Zhu. 2012. “Sand deformation around an uplift plate anchor.” J. Geotech. Geoenviron. Eng. 138 (6): 728–737. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000633.
Majer, J. 1955. “Zur berechnung von zugfundamenten.” [In German.] Osterreichister Bauzeitschift 10 (5): 85–90.
Matsuo, M. 1967. “Study of uplift resistance of footing (I).” Soils Found. 7 (4): 1–37. https://doi.org/10.3208/sandf1960.7.4_1.
Merifield, R. S., and S. W. Sloan. 2006. “The ultimate pullout capacity of anchors in frictional soils.” Can. Geotech. J. 43 (8): 852–868. https://doi.org/10.1139/t06-052.
Meyerhof, G. G. 1951. “The ultimate bearing capacity of foundations.” Géotechnique 2 (4): 301–332. https://doi.org/10.1680/geot.1951.2.4.301.
Meyerhof, G. G., and J. I. Adams. 1968. “The ultimate uplift capacity of foundations.” Can. Geotech. J. 5 (4): 225–244. https://doi.org/10.1139/t68-024.
Mors, H. 1959. “Das verhalten von mastgruendungen bei zugbeanspruchung.” [In German.] Bautechnik 36 (10): 367–378.
Mühlhaus, H., and I. Vardoulakis. 1987. “The thickness of shear bands in granular materials.” Géotechnique 37 (3): 271–283. https://doi.org/10.1680/geot.1987.37.3.271.
Murray, E. J., and J. D. Geddes. 1987. “Uplift of anchor plates in sand.” J. Geotech. Eng. 113 (3): 202–215. https://doi.org/10.1061/(ASCE)0733-9410(1987)113:3(202).
Murray, E. J., and J. D. Geddes. 1989. “Resistance of passive inclined anchors in cohesionless medium.” Géotechnique 39 (3): 417–431.
O’Sullivan, C. 2011. Particulate discrete element modelling: A geomechanics perspective. New York: Spon Press.
Ovesen, N. K. 1981. “Centrifuge tests to determine the uplift capacity of anchor slabs in sand.” In Vol. I of Proc., 10th Int. Conf. on Soil Mechanics and Foundation Engineering, 717–722. Rotterdam: A.A. Balkema.
Randolph, M., and S. Gourvenec. 2011. Offshore geotechnical engineering. Boca Raton, FL: CRC Press.
Rao, K. S. S., and J. Kumar. 1994. “Vertical uplift capacity of horizontal anchors.” J. Geotech. Eng. 120 (7): 1134–1147. https://doi.org/10.1061/(ASCE)0733-9410(1994)120:7(1134).
Rowe, R. K., and E. H. Davis. 1982. “The behaviour of anchor plates in sand.” Géotechnique 32 (1): 25–41. https://doi.org/10.1680/geot.1982.32.1.25.
Song, Z., Y. Hu, and M. F. Randolph. 2008. “Numerical simulation of vertical pullout of plate anchors in clay.” J. Geotech. Geoenviron. Eng. 134 (6): 866–875. https://doi.org/10.1061/(ASCE)1090-0241(2008)134:6(866).
Thornton, C. 2010. “Quasi-static simulations of compact polydisperse particle systems.” Particuology 8 (2): 119–126. https://doi.org/10.1016/j.partic.2009.07.007.
Uesugi, M., and H. Kishida. 1986. “Frictional resistance at yield between dry sand and mild steel.” Soils Found. 26 (4): 139–149. https://doi.org/10.3208/sandf1972.26.4_139.
Valent, P. J., R. J. Taylor, J. M. Atturio, and R. M. Beard. 1979. “Single anchor holding capacities for ocean thermal energy conversion (OTEC) in typical deep sea sediments.” Ocean Eng. 6 (1–2): 169–245. https://doi.org/10.1016/0029-8018(79)90005-2.
Vesić, A. S. 1971. “Breakout resistance of objects embedded in ocean bottom.” J. Soil Mech. & Foundations Div. 97 (9): 1183–1205.
White, D. J., C. Y. Cheuk, and M. D. Bolton. 2008. “The uplift resistance of pipes and plate anchors buried in sand.” Géotechnique 58 (10): 771. https://doi.org/10.1680/geot.2008.3692.
Yu, L., J. Liu, X. J. Kong, and Y. Hu. 2011. “Numerical study on plate anchor stability in clay.” Géotechnique 61 (3): 235–246. https://doi.org/10.1680/geot.8.P.071.
Zhang, N., and T. M. Evans. 2016. “Towards the anchoring of marine hydrokinetic energy devices: Three-dimensional discrete element method simulations of interface shear.” In Proc., Geo-Chicago 2016: Geotechnics for Sustainable Energy, Geotechnical Special Publication 270, 503–512. Reston, VA: ASCE.
Zhang, N., and T. M. Evans. 2017. “Offshore anchor penetration in sands—Granular simulations.” In Proc., GeoFrontiers 2017: Foundations, Geotechnical Special Publication 279, 132–142. Reston, VA: ASCE.
Zhang, N., and T. M. Evans. 2018. “Three dimensional discrete element method simulations of interface shear.” Soils Found. 58 (4): 941–956. https://doi.org/10.1016/j.sandf.2018.05.010.
Zhao, S., T. Evans, and X. Zhou. 2018. “Effects of curvature-related DEM contact model on the macro- and micro-mechanical behaviours of granular soils.” Géotechnique 68 (12): 1085–1098. https://doi.org/10.1680/jgeot.17.P.158.
Zhao, S., N. Zhang, X. Zhou, and L. Zhang. 2017. “Particle shape effects on fabric of granular random packing.” Powder Technol. 310: 175–186. https://doi.org/10.1016/j.powtec.2016.12.094.
Zhao, X., and T. M. Evans. 2009. “Discrete simulations of laboratory loading conditions.” Int. J. Geomech. 9 (4): 169–178. https://doi.org/10.1061/(ASCE)1532-3641(2009)9:4(169).
Information & Authors
Information
Published In
Copyright
© 2019 American Society of Civil Engineers.
History
Received: Jan 5, 2018
Accepted: Sep 7, 2018
Published online: Jan 14, 2019
Published in print: Apr 1, 2019
Discussion open until: Jun 14, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.