Mechanism and Countermeasure of Segmental Lining Damage Induced by Large Water Inflow from Excavation Face in Shield Tunneling
Publication: International Journal of Geomechanics
Volume 18, Issue 12
Abstract
This study investigated the influence of large water inflow from the excavation face on segmental lining damage when the earth-pressure balance (EPB) method was used in shield tunneling in a saturated silty sand layer. A refined numerical approach to investigate the damage mechanism and gradual failure mode of segmental lining was established by using the finite-element program Abaqus. The fluid–solid coupling was considered in simulating the tunneling process. The evolutions of permeability and elastic modulus of the grouting material were taken into account. The concrete damaged plasticity (CDP) model was adopted to model the segmental lining damage caused by large water inflow. Parametric studies were carried out to shed light on the mechanism of the structural response. The numerical analysis highlighted the effectiveness of the proposed method to simulate the lining damage. The mechanism of lining damage caused by large water inflow from the excavation face was identified, and it was found that sufficient water flow toward the tunnel compensated for the water loss from the excavation face and reduced the lining damage. It was also found that continuous grouting was an effective countermeasure to alleviate the lining damage.
Get full access to this article
View all available purchase options and get full access to this article.
References
Anagnostou, G., and K. Kovári. 1996. “Face stability conditions with earth-pressure balanced shields.” Tunnelling Underground Space Technol. 11 (2): 165–173. https://doi.org/10.1016/0886-7798(96)00017-X.
Arjnoi, P., J.-H. Jeong, C.-Y. Kim, and K.-H. Park. 2009. “Effect of drainage conditions on porewater pressure distributions and lining stresses in drained tunnels.” Tunnelling Underground Space Technol. 24 (4): 376–389. https://doi.org/10.1016/j.tust.2008.10.006.
Axelsson, M., G. Gustafson, and Å. Fransson. 2009. “Stop mechanism for cementitious grouts at different water-to-cement ratios.” Tunnelling Underground Space Technol. 24 (4): 390–397. https://doi.org/10.1016/j.tust.2008.11.001.
Bayati, M., and J. K. Hamidi. 2017. “A case study on TBM tunnelling in fault zones and lessons learned from ground improvement.” Tunnelling Underground Space Technol. 63: 162–170. https://doi.org/10.1016/j.tust.2016.12.006.
Belletti, B., C. Damoni, M. A. N. Hendriks, and A. de Boer. 2014. “Analytical and numerical evaluation of the design shear resistance of reinforced concrete slabs.” Struct. Concr. 15 (3): 317–330. https://doi.org/10.1002/suco.201300069.
Bian, X., Z.-S. Hong, and J.-W. Ding. 2016. “Evaluating the effect of soil structure on the ground response during shield tunnelling in Shanghai soft clay.” Tunnelling Underground Space Technol. 58: 120–132. https://doi.org/10.1016/j.tust.2016.05.003.
Bilotta, E., A. Paolillo, G. Russo, and S. Aversa. 2017. “Displacements induced by tunnelling under a historical building.” Tunnelling Underground Space Technol. 61: 221–232. https://doi.org/10.1016/j.tust.2016.10.007.
Bui, T. T., S. Abouri, A. Limam, W. S. A. NaNa, B. Tedoldi, and T. Roure. 2017. “Experimental investigation of shear strength of full-scale concrete slabs subjected to concentrated loads in nuclear buildings.” Eng. Struct. 131: 405–420. https://doi.org/10.1016/j.engstruct.2016.10.045.
Chinese National Standards. 2007. Steel for the reinforcement of concrete—Part 2: Hot rolled ribbed bars. [In Chinese.] GB1499. 2-2007. Hong Kong: China Standards Press.
Contini, A., A. Cividini, and G. Gioda. 2007. “Numerical evaluation of the surface displacements due to soil grouting and to tunnel excavation.” Int. J. Geomech. 7 (3): 217–226. https://doi.org/10.1061/(ASCE)1532-3641(2007)7:3(217).
Dalgıç, S. 2003. “Tunneling in fault zones, Tuzla tunnel, Turkey.” Tunnelling Underground Space Technol. 18 (5): 453–465. https://doi.org/10.1016/S0886-7798(03)00045-2.
Do, N.-A., D. Dias, P. Oreste, and I. Djeran-Maigre. 2014. “Three-dimensional numerical simulation for mechanized tunnelling in soft ground: The influence of the joint pattern.” Acta Geotech. 9 (4): 673–694. https://doi.org/10.1007/s11440-013-0279-7.
Eshraghi, A., and S. Zare. 2015. “Face stability evaluation of a TBM-driven tunnel in heterogeneous soil using a probabilistic approach.” Int. J. Geomech. 15 (6): 04014095. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000452.
Font-Capó, J., E. Vázquez-Suñé, J. Carrera, D. Martí, R. Carbonell, and A. Pérez-Estaun. 2011. “Groundwater inflow prediction in urban tunneling with a tunnel boring machine (TBM).” Eng. Geol. 121 (1–2): 46–54. https://doi.org/10.1016/j.enggeo.2011.04.012.
Galván, A., F. Peña, and J. Y. Moreno-Martínez. 2017. “Effect of TBM advance in the structural response of segmental tunnel lining.” Int. J. Geomech. 17 (9): 04017056. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000941.
Gong, Q. M., L. J. Yin, and Q. R. She. 2013. “TBM tunneling in marble rock masses with high in situ stress and large groundwater inflow: A case study in China.” Bull. Eng. Geol. Environ. 72 (2): 163–172. https://doi.org/10.1007/s10064-013-0460-0.
Hajjar, M., N. A. Hayati, M. M. Ahmadi, and S. A. Sadrnejad. 2015. “Longitudinal settlement profile in shallow tunnels in drained conditions.” Int. J. Geomech. 15 (6): 0414097. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000447.
Huangfu, M., M.-S. Wang, Z.-S. Tan, and X.-Y. Wang. 2010. “Analytical solutions for steady seepage into an underwater circular tunnel.” Tunnelling Underground Space Technol. 25 (4): 391–396. https://doi.org/10.1016/j.tust.2010.02.002.
Kasper, T., and G. Meschke. 2004. “A 3D finite element simulation model for TBM tunnelling in soft ground.” Int. J. Numer. Anal. Methods Geomech. 28 (14): 1441–1460. https://doi.org/10.1002/nag.395.
Katebi, H., A. H. Rezaei, M. Hajialilue-Bonab, and A. Tarifard. 2015. “Assessment the influence of ground stratification, tunnel and surface buildings specifications on shield tunnel lining loads (by FEM).” Tunnelling Underground Space Technol. 49: 67–78. https://doi.org/10.1016/j.tust.2015.04.004.
Kavvadas, M., D. Litsas, I. Vazaios, and P. Fortsakis. 2017. “Development of a 3D finite element model for shield EPB tunnelling.” Tunnelling Underground Space Technol. 65: 22–34. https://doi.org/10.1016/j.tust.2017.02.001.
Lambrughi, A., L. Medina Rodríguez, and R. Castellanza. 2012. “Development and validation of a 3D numerical model for TBM–EPB mechanised excavations.” Comput. Geotech. 40: 97–113. https://doi.org/10.1016/j.compgeo.2011.10.004.
Lavasan, A. A., C. Zhao, T. Barciaga, A. Schaufler, H. Steeb, and T. Schanz. 2018. “Numerical investigation of tunneling in saturated soil: The role of construction and operation periods.” Acta Geotech. 13 (3): 671–691. https://doi.org/10.1007/s11440-017-0595-4.
Lee, K. M., and X. W. Ge. 2001. “The equivalence of a jointed shield-driven tunnel lining to a continuous ring structure.” Can. Geotech. J. 38 (3): 461–483. https://doi.org/10.1139/t00-107.
Liu, C., Z. Zhang, and R. A. Regueiro. 2014. “Pile and pile group response to tunnelling using a large diameter slurry shield—Case study in Shanghai.” Comput. Geotech. 59: 21–43. https://doi.org/10.1016/j.compgeo.2014.03.006.
Liu, X., Y. Bai, Y. Yuan, and H. A. Mang. 2016. “Experimental investigation of the ultimate bearing capacity of continuously jointed segmental tunnel linings.” Struct. Infrastruct. Eng. 12 (10): 1364–1379. https://doi.org/10.1080/15732479.2015.1117115.
Liu, X.-X., S.-L. Shen, Y.-S. Xu, and Z.-Y. Yin. 2018. “Analytical approach for time-dependent groundwater inflow into shield tunnel face in confined aquifer.” Int. J. Numer. Anal. Methods Geomech. 42 (4): 655–673. https://doi.org/10.1002/nag.2760.
Meschke, G., C. Kropik, and H. A. Mang. 1996. “Numerical analyses of tunnel linings by means of a viscoplastic material model for shotcrete.” Int. J. Numer. Methods Eng. 39 (18): 3145–3162. https://doi.org/10.1002/(SICI)1097-0207(19960930)39:18%3C3145::AID-NME992%3E3.0.CO;2-M.
Meschke, G., F. Nagel, and J. Stascheit. 2011. “Computational simulation of mechanized tunneling as part of an integrated decision support platform.” Int. J. Geomech. 11 (6): 519–528. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000044.
Nagel, F., J. Stascheit, and G. Meschke. 2012. “Numerical simulation of interactions between the shield-supported tunnel construction process and the response of soft water-saturated soils.” Int. J. Geomech. 12 (6): 689–696. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000174.
Nana, W. S. A., T. T. Bui, A. Limam, and S. Abouri. 2017. “Experimental and numerical modelling of shear behaviour of full-scale RC slabs under concentrated loads.” Structures 10: 96–116. https://doi.org/10.1016/j.istruc.2017.02.004.
Ngan Vu, M., W. Broere, and J. W. Bosch. 2017. “Structural analysis for shallow tunnels in soft soils.” Int. J. Geomech. 17 (8): 04017038. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000866.
Ni, J. C., and W. C. Cheng. 2010. “Monitoring and modeling grout efficiency of lifting structure in soft clay.” Int. J. Geomech. 10 (6): 223–229. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000026.
Ninić, J., and G. Meschke. 2017. “Simulation based evaluation of time-variant loadings acting on tunnel linings during mechanized tunnel construction.” Eng. Struct. 135: 21–40. https://doi.org/10.1016/j.engstruct.2016.12.043.
Pan, Q., and D. Dias. 2016. “The effect of pore water pressure on tunnel face stability.” Int. J. Numer. Anal. Methods Geomech. 40 (15): 2123–2136. https://doi.org/10.1002/nag.2528.
Perrochet, P. 2005. “Confined flow into a tunnel during progressive drilling: An analytical solution.” Groundwater 43 (6): 943–946. https://doi.org/10.1111/j.1745-6584.2005.00108.x.
Ren, D.-J., S.-L. Shen, W.-C. Cheng, N. Zhang, and Z.-F. Wang. 2016. “Geological formation and geo-hazards during subway construction in Guangzhou.” Environ. Earth Sci. 75 (11): 934. https://doi.org/10.1007/s12665-016-5710-6.
Shaterpour-Mamaghani, A., D. Tumac, and E. Avunduk. 2016. “Double shield TBM performance analysis in difficult ground conditions: A case study in the Gerede water tunnel, Turkey.” Bull. Eng. Geol. Environ. 75 (1): 251–262. https://doi.org/10.1007/s10064-015-0743-8.
Shi, C., C. Cao, M. Lei, L. Peng, and H. Ai. 2016. “Effects of lateral unloading on the mechanical and deformation performance of shield tunnel segment joints.” Tunnelling Underground Space Technol. 51: 175–188. https://doi.org/10.1016/j.tust.2015.10.033.
SIMULIA. 2016. ABAQUS/standard analysis user’s manual. Providence, RI: SIMULIA.
Talmon, A. M., and A. Bezuijen. 2009. “Simulating the consolidation of TBM grout at Noordplaspolder.” Tunnelling Underground Space Technol. 24 (5): 493–499. https://doi.org/10.1016/j.tust.2008.12.004.
Tseng, D. J., B. R. Tsai, and L. C. Chang. 2001. “A case study on ground treatment for a rock tunnel with high groundwater ingression in Taiwan.” Tunnelling Underground Space Technol. 16 (3): 175–183. https://doi.org/10.1016/S0886-7798(01)00055-4.
Wang, Y., H. Jing, H. Su, and J. Xie. 2017. “Effect of a fault fracture zone on the stability of tunnel-surrounding rock.” Int. J. Geomech. 17 (6): 04016135. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000837.
Zhang, Z. X., C. Liu, X. Huang, C. Y. Kwok, and L. Teng. 2016. “Three-dimensional finite-element analysis on ground responses during twin-tunnel construction using the URUP method.” Tunnelling Underground Space Technol. 58: 133–146. https://doi.org/10.1016/j.tust.2016.05.001.
Zhao, T., W. Liu, and Z. Ye. 2017. “Effects of water inrush from tunnel excavation face on the deformation and mechanical performance of shield tunnel segment joints.” Adv. Civ. Eng. 2017: 5913640. https://doi.org/10.1155/2017/5913640.
Information & Authors
Information
Published In
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Mar 2, 2018
Accepted: Jun 12, 2018
Published online: Sep 21, 2018
Published in print: Dec 1, 2018
Discussion open until: Feb 21, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.