Pore Pressure Response to Dynamically Installed Penetrometers
Publication: International Journal of Geomechanics
Volume 18, Issue 7
Abstract
Potentially, a seabed may be characterized rapidly and economically by using dynamically installed free-falling penetrometers (FFPs). Because of their relatively rapid deployment and recovery, FFPs may be preferred over conventional full-flow or cone penetrometers for characterizing seabeds. However, despite several successful field trials of FFPs, significant uncertainty still exists about the data interpretation, mainly because of the fast nature of the penetration process, during which regions of the soil body close to the penetrometer experience very high strain rates. The consequence of such high strain rates on pore pressure measurement is not well known. Furthermore, the rigorous numerical analysis of the problem is notoriously difficult because it involves large deformations, dynamics, hydrodynamic coupling, highly nonlinear material behavior, rate dependency, and contact mechanics. A finite-element procedure was developed and used in this study to provide a dynamic coupled solution for the penetrometer impact and burial into saturated clay. Subsequently, some mechanisms involved in the generation of excess pore pressures were investigated with specific attention given to the effects of the penetrometer tip geometry and the location of the pore pressure measuring devices. An important numerical challenge in modeling this problem is highlighted in this paper. It concerns the numerical diffusion that can occur because of the remeshing process required in this large deformation, moving boundary problem.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The work described in this paper received financial support from the Australian Research Council through Discovery Projects DP110101033 and DP150101340 and its Centre of Excellence for Geotechnical Science and Engineering. This support is gratefully acknowledged.
References
Abelev, A., Simeonov, J., and Valent, P. (2009). “Numerical investigation of dynamic free-fall penetrometers in soft cohesive marine sediments using a finite element approach.” OCEANS 2009, MTS/IEEE Biloxi—Marine Technology for Our Future: Global and Local Challenges, IEEE, New York.
Akal, T., and Stoll, R. D. (1995). “An expendable penetrometer for rapid assessment of seafloor parameters.” Proc., OCEANS ’95, MTS/IEEE, Challenges of Our Changing Global Environment, Vol. 3, IEEE, New York, 1822–1826.
Akiyoshi, T., Fuchida, K., and Fang, H. L. (1994). “Absorbing boundary conditions for dynamic analysis of fluid-saturated porous media.” Soil Dyn. Earthquake Eng., 13(6), 387–397.
Beard, R. (1981). “A penetrometer for deep ocean seafloor exploration.” Proc., OCEANS ’81, Conf. Record, Vol. 1, IEEE, New York, 668–673.
Benson, D. J. (1989). “An efficient, accurate, simple ale method for nonlinear finite element programs.” Comput. Methods Appl. Mech. Eng., 72(3), 305–350.
Biot, M. A. (1956). “Theory of propagation of elastic waves in a fluid-saturated porous solid. I. Low-frequency range.” J. Acoust. Soc. Am., 28(2), 168–191.
Biscontin, G., and Pestana, J. (2001). “Influence of peripheral velocity on vane shear strength of an artificial clay.” Geotech. Test. J., 24(4), 423–430.
Bjerrum, L. (1967). “Engineering geology of Norwegian normally-consolidated marine clays as related to settlements of buildings.” Géotechnique, 17(2), 81–118.
Bjerrum, L., Simons, N., and Torblaa, I., (1958). “The effect of time on the shear strength of a soft marine clay.” Proc., Brussels Conf., Earth Pressure Problems, Publ. 33, Vol. 1, Norwegian Geotechnical Institute, 148–158.
Budhu, M., and Wu, C. S. (1992). “Numerical analysis of sampling disturbances in clay soils.” Int. J. Numer. Anal. Methods Geomech., 16(7), 467–492.
Buhler, R. L., and Audibert, J. M. E. (2012). “Rate-effect correction methods for free-fall CPT data in deepwater Gulf of Mexico—An operator’s perspective.” Proc, 7th Int. Conf., Offshore Site Investigation and Geotechnics: Integrated Geotechnologies—Present and Future. Society for Underwater Technology, London.
Carter, J. P., Booker, J. R., and Davis, E. H. (1977). “Finite deformation of an elasto-plastic soil.” Int. J. Numer. Methods Eng., 1(1), 25–43.
Carter, J. P., Sabetamal, H., Nazem, M., and Sloan, S. W. (2015). “One-dimensional test problems for dynamic consolidation.” Acta Geotech., 10(1), 173–178.
Casacrande, A., and Wilson, S. D. (1951). “Effect of rate of loading on the strength of clays and shales at constant water content.” Géotechnique, 2(3), 251–263.
Chow, S. H., O’Loughlin, C. D., and Randolph, M. F. (2014). “Soil strength estimation and pore pressure dissipation for free-fall piezocone in soft clay.” Géotechnique, 64(10), 817–824.
Chow, S. H., O’Loughlin, C. D., White, D. J., and Randolph, M. F. (2017). “An extended interpretation of the free-fall piezocone test in clay.” Géotechnique, 67(12), 1090–1103.
Chung, J., and Hulbert, G. M. (1993). “A time integration algorithm for structural dynamics with improved numerical dissipation: The generalized-α method.” J. Appl. Mech., 60(2), 371–375.
Corapcioglu, M. Y., and Tuncay, K. (1996). “Chapter 5: Propagation of waves in porous media.” Advances in porous media, M. Y. Corapcioglu, ed., Vol. 3, Elsevier Science, Amsterdam, Netherlands, 361–440.
Dayal, U., Allen, J. H., and Jones, J. M. (1975). “Use of an impact penetrometer for the evaluation of the in-situ strength of marine sediments.” Mar. Geotechnol., 1(2), 73–89.
de Borst, R. (1982). “Calculation of collapse loads using higher order elements.” Proc., IUTAM Symp., Deformation and Failure of Granular Materials, P. A. Vermeer and H. J. Luger, eds., A. A. Balkema, Rotterdam, Netherlands, 503–513.
Einav, I., and Randolph, M. (2006). “Effect of strain rate on mobilised strength and thickness of curved shear bands.” Géotechnique, 56(7), 501–504.
Fischer, K. A., and Wriggers, P. (2005). “Frictionless 2D contact formulations for finite deformations based on the mortar method.” Comput. Mech., 36(3), 226–244.
Flanagan, D. P., and Belytschko, T. A. (1981). “A uniform strain hexahedron and quadrilateral and orthogonal hourglass control.” Int. J. Numer. Methods Eng., 17(5), 697–706.
Ganzha, V. G., and Vorozhtsov, E. V. (1996). Numerical solutions for partial differential equations: Problem solving with Mathematica, CRC, Boca Raton, FL.
Garagash, D. I. (2005). “Diffuse vs. localized instability in compacting geomaterials under undrained conditions.” Geomechanics: Testing, modeling, and simulation, Geotechnical special publication 143, J. A. Yamamuro and J. Koseki, eds., ASCE, Reston, VA, 444–462.
Graham, J., Crooks, J. H. A., and Bell, A. L. (1983). “Time effects on the stress–strain behaviour of natural soft clays.” Géotechnique, 33(3), 327–340.
Griffiths, D. V. (1982). “Elasto-plastic analyses of deep foundations in cohesive soil.” Int. J. Numer. Anal. Methods Geomech., 6(2), 211–218.
Huétink, J., Vreede, P. T., and van der Lugt, J. (1990). “Progress in mixed Eulerian-Lagrangian finite element simulation of forming processes.” Int. J. Numer. Methods Eng., 30(8), 1441–1457.
Jeanjean, P., Spikula, D., and Young, A., (2012). “Technical vetting of free-fall cone penetrometer.” Proc., 7th Int. Conf., Offshore Site Investigation and Geotechnics: Integrated Geotechnologies—Present and Future. Society for Underwater Technology, London, 15–18.
Jung, B. C., and Biscontin, G., (2006). “Modeling of strain rate effects on clay in simple shear.” Proc., GeoCongress 2006: Geotechnical Engineering in the Information Technology Age, D. J. DeGroot, J. T. DeJong, D. Frost, and L. G. Baise, eds., ASCE, Reston, VA.
Kellezi, L. (2000). “Local transmitting boundaries for transient elastic analysis.” Soil Dyn. Earthquake Eng., 19(7), 533–547.
Kiousis, P. D., Voyiadjis, G. Z., and Tumay, M. T. (1988). “A large strain theory and its application in the analysis of the cone penetration mechanism.” Int. J. Numer. Anal. Methods Geomech., 12(1), 45–60.
Leroueil, S., Kabbaj, M., Tavenas, F., and Bouchard, R. (1985). “Stress-strain-strain rate relation for the compressibility of sensitive natural clays.” Géotechnique, 35(2), 159–180.
Levadoux, J. N., and Baligh, M. M. (1986). “Consolidation after undrained piezocone penetration. I: Prediction.” J. Geotech. Engrg., 707–726.
Le Veque, R. J. (1992). Numerical methods for conservation laws: Lectures in mathematics, Birkhauser, Berlin.
Liyanapathirana, D. S. (2009). “Arbitrary Lagrangian Eulerian based finite element analysis of cone penetration in soft clay.” Comput. Geotech., 36(5), 851–860.
Mitchell, J. K., and Soga, K. (2005). Fundamentals of soil behavior, 3rd Ed., John Wiley & Sons, Hoboken, NJ.
Morland, L. W. (1972). “A simple constitutive theory for a fluid-saturated porous solid.” J. Geophys. Res., 77(5), 890–900.
Mulukutla, G. K. (2009). “Determination of geotechnical properties of seafloor sediment using a free fall penetrometer.” Ph.D. thesis, Univ. of New Hampshire, Durham, NH.
Namikawa, T. (2001). “Delayed plastic model for time-dependent behaviour of materials.” Int. J. Numer. Anal. Methods Geomech., 25(6), 605–627.
Nazem, M., Carter, J. P., Airey, D. W., and Chow, S. H. (2012). “Dynamic analysis of a smooth penetrometer free-falling into uniform clay.” Géotechnique, 62(10), 893–905.
Nazem, M., Sheng, D., Carter, J. P., and Sloan, S. W. (2008). “Arbitrary Lagrangian-Eulerian method for large-strain consolidation problems.” Int. J. Numer. Anal. Methods Geomech., 32(9), 1023–1050.
Perzyna, P., (1963). “The constitutive equations for work-hardening and rate sensitive plastic materials.” Proc., Vibration Problems, 281–290.
Perzyna, P. (1966). “Fundamental problems in viscoplasticity.” Adv. Appl. Mech., 9, 243–377.
Puso, M. A., and Laursen, T. A. (2003). “Mesh tying on curved interfaces in 3D.” Eng. Comput., 20(3), 305–319.
Rao, P.-P., Chen, Q., Li, L., Nimbalkar, S., and Cui, J. (2017). “Elastoplastic solution for spherical cavity expansion in modified cam-clay soil under drained condition.” Int. J. Geomech., 06017005.
Richardson, M. D. (2008). “Dynamically installed anchors for floating offshore structures.” Ph.D. thesis, Univ. of Western Australia, Perth, Australia.
Robertson, P. K., Sully, J. P., Woeller, D. J., Lunne, T., Powell, J. J. M., and Gillespie, D. G. (1992). “Estimating coefficient of consolidation from piezocone tests.” Can. Geotech. J., 29(4), 539–550.
Rodríguez-Ferran, A., Casadei, F., and Huerta, A. (1998). “ALE stress update for transient and quasistatic processes.” Int. J. Numer. Methods Eng., 43(2), 241–262.
Sabetamal, H. (2015). “Finite element algorithms for dynamic analysis of geotechnical problems.” Ph.D. thesis, Univ. of Newcastle, Callaghan, Australia.
Sabetamal, H., Carter, J. P., Nazem, M., and Sloan, S. W. (2016a). “Coupled analysis of dynamically penetrating anchors.” Comput. Geotech., 77, 26–44.
Sabetamal, H., Carter, J. P., Nazem, M., and Sloan, S. W. (2016b). “Numerical study of the effects of strain rate on the behaviour of dynamically penetrating anchors in clay.” Proc., 7th Int. Conf., Computational Methods, G. R. Liu and S. Li, eds., Vol. 3, Scientech, Mason, OH, 1777–1782.
Sabetamal, H., Nazem, M., Carter, J. P., and Sloan, S. W. (2014). “Large deformation dynamic analysis of saturated porous media with applications to penetration problems.” Comput. Geotech., 55, 117–131.
Sabetamal, H., Nazem, M., Sloan, S. W., and Carter, J. P. (2016c). “Frictionless contact formulation for dynamic analysis of nonlinear saturated porous media based on the mortar method.” Int. J. Numer. Anal. Methods Geomech., 40(1), 25–61.
Salgado, R., and Prezzi, M. (2007). “Computation of cavity expansion pressure and penetration resistance in sands.” Int. J. Geomech., 251–265.
Salgado, R., and Randolph, M. F. (2001). “Analysis of cavity expansion in sand.” Int. J. Geomech., 175–192.
Seifert, A., Stegmann, S., Mörz, T., Lange, M., Wever, T., and Kopf, A. (2008). “In situ pore-pressure evolution during dynamic CPT measurements in soft sediments of the western Baltic Sea.” Geo-Mar. Lett., 28(4), 213–227.
Sheahan, T. C. (2005). “A soil structure index to predict rate dependence of stress-strain behavior.” Geomechanics: Testing, modeling, and simulation, Geotechnical special publication 143, J. A. Yamamuro and J. Koseki, eds., ASCE, Reston, VA, 81–97.
Sheahan, T. C., Ladd, C. C., and Germaine, J. T. (1996). “Rate dependent undrained shear behavior of saturated clay.” J. Geotech. Engrg., 99–108.
Sheng, D., Wriggers, P., and Sloan, S. W. (2007). “Application of frictional contact in geotechnical engineering.” Int. J. Geomech., 176–185.
Skempton, A. W. (1948). “Vane tests in alluvial plain of the River Forth near Grangemouth.” Géotechnique, 1(2), 111–124.
Sloan, S. W., and Randolph, M. F. (1982). “Numerical prediction of collapse loads using finite element methods.” Int. J. Numer. Anal. Methods Geomech., 6(1), 47–76.
Small, J. C., Booker, J. R., and Davis, E. H. (1976). “Elasto-plastic consolidation of soil.” Int. J. Solids Struct., 12(6), 431–448.
SNAC [Computer software]. Priority Research Center for Geotechnical Science and Engineering, Univ. of Newcastle, Newcastle, NSW, Australia.
Stark, N., Dantec, N. L., Corella, J. P., Barry, D. A., Lemmin, U., Giradclos, S., and Kopf, A. (2013). “Deployment of a dynamic penetrometer from manned submersibles for fine-scale geomorphology studies.” Limnol. Oceanogr. Methods, 11(10), 529–539.
Stark, N., Kopf, A., Hanff, H., Stegmann, S., and Wilkens, R. (2009). “Geotechnical investigations of sandy seafloors using dynamic penetrometers.” Proc., OCEANS 2009, MTS/IEEE Biloxi—Marine Technology for Our Future: Global and Local Challenges, IEEE, New York.
Stark, N., Radosavljevic, B., Quinn, B., and Lantuit, H. (2017). “Application of portable free-fall penetrometer for geotechnical investigation of Arctic nearshore zone.” Can. Geotech. J., 54(1), 31–46.
Stegmann, S., Moerz, T., and Kopf, A. (2006). “Initial results of a new free fall-cone penetrometer (FF-CPT) for geotechnical in situ characterisation of soft marine sediments.” Nor. Geol. Tidsskr., 86(3), 199–208.
Steiner, A., et al. (2014). “In situ dynamic piezocone penetrometer tests in natural clayey soils—A reappraisal of strain-rate corrections.” Can. Geotech. J., 51(3), 272–288.
Steiner, A., L’Heureux, J.-S., Kopf, A., Vanneste, M., Longva, O., Lange, M., and Haflidason, H. (2012). “An in-situ free-fall piezocone penetrometer for characterizing soft and sensitive clays at Finneidfjord (Northern Norway).” Proc., 5th Int. Symp.: Submarine Mass Movements and Their Consequences, Y. Yamada et al., eds., Springer, Dordrecht, Netherlands, 99–109.
Stephan, S., Kaul, N., and Villinger, H. (2012). “The lance insertion retardation meter (LIRmeter): An instrument for in situ determination of sea floor properties—Technical description and performance evaluation.” Mar. Geophys. Res., 33(3), 209–221.
Stoker, H. C. (1999). “Developments of the arbitrary Lagrangian–Eulerian method in non-linear solid mechanics applications to forming processes.” Ph.D. thesis, Univ. of Twente, Enschede, Netherlands.
Stoll, R., Sun, Y.-F., and Bitte, I. (2007). “Seafloor properties from penetrometer tests.” IEEE J. Oceanic Eng., 32(1), 57–63.
Straughan, B. (2008). Stability and wave motion in porous media, Vol. 165. Springer, New York.
True, D. G. (1976). “Undrained vertical penetration into ocean bottom soils.” Ph.D. dissertation, Univ. of California, Berkeley, CA.
Truesdell, C., and Toupin, R. (1960). “The classical field theories.” Handbuch der physik, S. Flügge, ed., Vol. 3, Springer, Berlin, 227–858.
Vaid, Y. P., and Campanella, R. G. (1977). “Time-dependent behavior of undisturbed clay.” J. Geotech. Engrg. Div., 103(7), 693–709.
van den Berg, P. (1991). “Numerical model for cone penetration.” Proc., 7th Int. Conf., Computer Methods and Advances in Geomechanics, G. Beer, J. R. Booker, and J. P. C. Carter, eds., A. A. Balkema, Rotterdam, Netherlands, 1777–1782.
van Haaren, M. J., Stoker, H. C., van den Boogaard, A. H., and Huétink, J. (2000). “The ALE-method with triangular elements: Direct convection of integration point values.” Int. J. Numer. Methods Eng., 49(5), 697–720.
Van Leer, B. (1977). “Towards the ultimate conservative difference scheme. IV. A new approach to numerical convection.” J. Comput. Phys., 23(3), 276–299.
Voyiadjis, G. Z., and Abu-Farsakh, Y. M. (1997). “Coupled theory of mixtures for clayey soils.” Comput. Geotech., 20, 195–222.
Voyiadjis, G. Z., and Song, C. R. (2003). “Determination of hydraulic conductivity using piezocone penetration test.” Int. J. Geomech., 217–224.
Wei, L., Abu-Farsakh, M. Y., and Tumay, M. T. (2005). “Finite-element analysis of inclined piezocone penetration test in clays.” Int. J. Geomech., 167–178.
Yang, C., Carter, J. P., Sheng, D., and Sloan, S. W. (2016). “An isotach elastoplastic constitutive model for natural soft clays.” Comput. Geotech., 77(Jul), 134–155.
Young, A. G., Bernard, B. B., Remmes, B. D., Babb, L., and Brooks, J. M., (2011). “CPT stinger—An innovative method to obtain CPT data for integrated geoscience studies.” Proc., Offshore Technology Conf., Society of Petroleum Engineers, Richardson, TX.
Yu, H. S., and Carter, J. P. (2003). “Rigorous similarity solutions for cavity expansion in cohesive-frictional soils.” Int. J. Geomech., 233–258.
Yu, H., Herrmann, L. R., and Boulanger, R. W. (2000). “Analysis of steady cone penetration in clay.” J. Geotech. Geoenviron. Eng., 594–605.
Zhou, H., and Randolph, M. F. (2007). “Computational techniques and shear band development for cylindrical and spherical penetrometers in strain-softening clay.” Int. J. Geomech., 287–295.
Zienkiewicz, O. C., and Zhu, J. Z. (1992). “The superconvergent patch recovery and a posteriori error estimates. Part 1: The recovery technique.” Int. J. Numer. Methods Eng., 33(7), 1331–1364.
Zou, J.-f., and Xia, Z-q. (2017). “Closed-form solution for cavity expansion in strain-softening and undrained soil mass based on the unified strength failure criterion.” Int. J. Geomech., 04017046.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 18 • Issue 7 • July 2018
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Mar 1, 2017
Accepted: Dec 27, 2017
Published online: Apr 23, 2018
Published in print: Jul 1, 2018
Discussion open until: Sep 23, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.