Verification of the CSDS Model in Estimating the Postpeak Behavior of Hard Rocks
Publication: International Journal of Geomechanics
Volume 18, Issue 3
Abstract
Rockburst is a serious instability problem in Canadian deep underground excavations and is related to the postpeak behavior of hard and brittle rocks. Rockburst potential can be estimated by comparing the postpeak stiffness of the failed rock and the prepeak stiffness of the surrounding rock. Estimation of the postpeak behavior of hard and brittle rocks can help engineers evaluate and predict potential severe instabilities. The complete stress-displacement surface (CSDS) model is an analytical model (a constitutive model for rock joints) that estimates rockburst proneness. This paper aims to verify the application of the CSDS solution for estimating the postpeak curve (postpeak stiffness) in intact hard rocks by experimental results. To verify the model properties used in the model, different types of rock mechanics tests have been performed. The results show that the CSDS model can be used to estimate the postpeak behavior of medium to hard rocks.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge Raglan Mine (Glencore Group, London) for providing the rock cores (BAS and MG) used in this study. The scanning on the fracture surfaces and direct shear tests in this study were performed at the Department of Civil Engineering, University of Sherbrooke. This support is gratefully acknowledged.
References
Adoko, A. C., Gokceoglu, C., Wu, L., and Zuo, Q. J. (2013). “Knowledge-based and data-driven fuzzy modeling for rockburst prediction.” Int. J. Rock Mech. Min. Sci., 61(Jul), 86–95.
Altindag, R. (2010). “Assessment of some brittleness indexes in rock-drilling efficiency.” Rock Mech. Rock Eng., 43(3), 361–370.
ASTM. (2008). “Standard test method for performing laboratory direct shear strength tests of rock specimens under constant normal force.” D5607-08, West Conshohocken, PA.
Aubertin, M., Gill, D. E., and Simon, R. (1994). “On the use of the brittleness index modified (BIM) to estimate the post-peak behavior of rocks.” Proc., First North American Rock Mech. Symp., NARMS’94, A.A. Balkema, Rotterdam, Netherlands, 945–952.
Aubertin, M., and Simon, R. (1997). “A damage initiation criterion for low porosity rocks.” Int. J. Rock Mech. Min. Sci., 34(3–4), 17.e1–17.e15.
Barton, N. (1973). “Review of a new shear strength criterion for rock joints.” Eng. Geol., 7(4), 287–332.
Brady, B. H. G., and Brown, E. T. (2006). Rock mechanics for underground mining, 1st Ed., Allen & Unwin, London.
Cai, M., Kaiser, P. K., and Duff, D. J. (2012). “Rock support design in burst-prone ground utilizing an interactive design tool.” Proc., 46th U.S. Rock Mechanics/Geomechanics Symp., American Rock Mechanics Association, Alexandria, VA.
Cook, N. G. W. (1965). “A note on rockburst considered as a problem of stability.” J. South Afr. Inst. Min. Metall., 65, 437–446.
Cook, N. G. W. (1987). “Coupled processes in geomechanics.” Coupled processes associated with nuclear waste repositories, C. F. Tsang, ed., Academic Press, Orlando, FL, 39–66.
Dai, S. T., Labuz, J. F., and Carvalho, F. (2000). “Softening response of rock observed in plane-strain compression, trends of rock mechanics.” Proc., Sessions of Geo-Denver 2000, Trends in Rock Mechanics, Geotechnical special publication, 290, ASCE, Reston, VA, 152–163.
De Beer, W., and Mendecki, A. J. (1998). “Rockburst prediction-case studies using a kinematics of failure approach.” J. South Afr. Inst. Min. Metall., 98, 65–74.
Deng, D., Simon, R., and Aubertin, M. (2004). “A geometrical approach for the estimation of scale effects in rock joint behavior.” Proc., 57th Canadian Geotechnical Conf., GeoQuebec2004 Quebec, 33–40.
Deng, D., Simon, R., and Aubertin, M. (2006). “Modelling shear and normal behavior of filled rock joints.” GeoCongress 2006, ASCE, Reston, VA.
Dong, L. J., Li, X. B., and Kang, P. E. N. G. (2013). “Prediction of rockburst classification using Random Forest.” Trans. Nonferrous Met. Soc. China, 23(2), 472–477.
Dyskin, A. V., and Germanovich, L. N. (1993). Model of rockburst caused by cracks growing near free-surface, A.A. Balkema, Rotterdam, Netherlands.
Fairhurst, C. E., and Hudson, J. A. (1999). “Draft ISRM suggested method for the complete stress-strain curve for intact rock in uniaxial compression.” Int. J. Rock Mech. Min. Sci., 36(3), 279–289.
Gill, D. E., and Aubertin, M. (1988). “Évaluation du potentiel de coups de terrain dans les mines d'Abitibi.” Rapport de recherche de l'URSTM, l'Institut de Recherche en Santé et Sécurité du Travail (IRSST), Montréal.
Gill, D. E., Aubertin, M., and Simon, R. (1993). “A practical engineering approach to the evaluation of rockburst potential.” Proc., 3rd Int. Symp. on Rockbursts and Seismicity in Mines, R. P. Young, ed., A.A. Balkema, Rotterdam, Netherlands, 63–68.
Goodman, R. E. (1976). Methods of geological engineering in discontinuous rock, West, Eagan, MN, 472.
Grasselli, G., and Egger, P. (2003). “Constitutive law for the shear strength of rock joints based on three-dimensional surface parameters.” Int. J. Rock Mech. Min. Sci., 40(1), 25–40.
Haijun, C., Nenghui, L., Dexin, N., and Yuequan, S. (2003). “Prediction of rockburst by artificial neural network.” Chin. J. Rock Mech. Eng., 22(5), 762–768.
Hajiabdolmajid, V., and Kaiser, P. (2003). “Brittleness of rock and stability assessment in hard rock tunnelling.” Tunnelling Underground Space Technol., 18(1), 35–48.
Hucka, V., and Das, B. (1974). “Brittleness determination of rocks by different methods.” Int J Rock Mech. Min. Sci. Geomech. Abstr., 11(10), 389–392.
Hudson, J. A. (1989). Rock mechanics principles in engineering practice, Butterworths, Boston, 67.
Hudson, J. A., Brown, E. T., and Fairhurst, C. (1971). “Optimizing the control of rock failure in servo-controlled laboratory test.” Rock Mech., 3(4), 217– 224.
Johnston, J. C. (1988). “A survey of mining associated rockbursts.” Master’s thesis, Massachusetts Institute of Technology, Cambridge, MA.
Kaiser, P., et al. (1995). The Canadian rockburst research program 1990–1995, Vol. 2, CAMIRO Mining Div., Sudbury, ON, Canada.
Khosravi, A. (2016). “Investigation of post-peak behavior of hard rocks.” Ph.D. thesis, École Polytechnique de Montréal, Montréal.
Kidybiński, A. (1981). “Bursting liability indices of coal.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 18(4), 295–304.
Ladanyi, B., and Archambault, G. (1969).” Simulation of the shear behavior of a jointed rock mass.” Proc., 11th Symp. on Rock Mechanics, American Rock Mechanics Association, Berkeley, CA, 105–125.
Lee, S. M., Park, B. S., and Lee, S. W. (2004). “Analysis of rockbursts that have occurred in a waterway tunnel in Korea.” Int. J. Rock Mech. Min. Sci., 41(May), 911–916.
Li, Z.-H., Dou, L-M., Lu, C.-P., Mu, Z.-L., and Cao, A.-Y. (2008). “Study on fault induced rock bursts.” J. China Univ. Min. Technol., 18(3), 321–326.
McGarr, A. (1993). Keynote address: Factors influencing the strong ground motion from mining induced tremors. Proc., 3rd Int. Symp. on Rockbursts and Seismicity in Mines, R. P. Young, ed., A.A. Balkema, Rotterdam, Netherlands, 3–12.
Meng, F., Zhou, H., Zhang, C., Xu, R., and Lu, J. (2015). “Evaluation methodology of brittleness of rock based on post-peak stress–strain curves.” Rock Mech. Rock Eng., 48(5), 1787–1805.
Mitri, H. S. (2007). “Assessment of horizontal pillar burst in deep hard rock mines.” Int. J. Risk Assess. Manage., 7(5), 695–707.
Patton, F. D. (1966). “Multiple modes of shear failure in rock.” Proc., 1st Congress of the Int. Society of Rock Mechanics, Lisbon, 1, 509–513.
Petukhov, I. (1972). Rock bursts in coal mines, Nedra, Moscow.
Qiao, C. S., and Tian, Z. Y. (1998). “Study of the possibility of rockburst in Dong-gua-shan copper mine.” Chin. J. Rock Mech. Eng., 17, 917–921.
Reichmuth, D. R. (1967). “Point load testing of brittle materials to determine tensile strength and relative brittleness.” Proc., 9th U.S. Symp. on Rock Mechanics (USRMS), American Rock Mechanics Association, Alexandria, VA, 34–159.
Rummel, F., and Fairhurst, C. (1970). “Determination of the post-failure behavior of brittle rock using a servo-controlled testing machine.” Rock Mech., 2(4), 189–204.
Saeb, S. (1990). “A variance on the Ladanyi and Archambault’s shear strength criterion.” Rock joints, N. Barton and O. Stephansson, eds., Balkema, Rotterdam, Netherlands, 701–705.
Saeb, S., and Amadei, B. (1992). “Modelling rock joints under shear and normal loading.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 29(3), 267–278.
Sainoki, A., and Mitri, H. S. (2014). “Dynamic behaviour of mining-induced fault slip.” Int. J. Rock Mech. Min. Sci., 66(Feb), 19–29.
Salamon, M. D. G. (1974). “Rock mechanics of underground excavations.” Advances in Rock Mechanics, Proc. 3rd Congress ISRM, Denver 1B, National Academy of Sciences, Washington, DC, 951–1009.
Salamon, M. D. G. (1993). “Keynote address: Some applications of geomechanical modelling in rockburst and related research.” Rockbursts and seismicity in mines, R. P. Young, ed., A.A. Balkema, Rotterdam, Netherlands, 297–309.
Simon, R. (1999). “Analysis of fault-slip mechanisms in hard rock mining.” Ph.D. thesis, McGill Univ., Montreal.
Simon, R., Aubertin, M., and Deng, D. (2003). “Estimation of post-peak behavior of brittle rocks using a constitutive model for rock joints.” Proc., 56th Canadian Geotechnical Conf. and 4th Joint IAH-CNC and CGS Groundwater Specialty Conf., Winnipeg, Canada.
Singh, S. P. (1989). “Classification of mine workings according to their rockburst proneness.” Min. Sci. Technol., 8(3), 253–262.
Stiller, H., Hurtig, E., Grosser, H., and Knoll, P. (1983). “On the nature of mining tremors.” Earthquake Predict. Res., 2, 57–63.
Su, G.-S., et al. (2009 ). “Rockburst prediction using Gaussian process machine learning.” Proc., CiSE 2009, IEEE, Piscataway, NJ.
Tang, C. A., Tham, L. G., Lee, P. K. K., Tsui, Y., and Liu, H. (2000). “Numerical studies of the influence of microstructure on rock failure in uniaxial compression D. Part II: Constraint, slenderness and size effect.” Int. J. Rock Mech. Min. Sci., 37(4), 571–583.
Tarasov, B. G., and Potvin, Y. (2013). “Universal criteria for rock brittleness estimation under triaxial compression.” Int. J. Rock Mech. Min. Sci., 59(Apr), 57–69.
Tremblay, D., Simon, R., and Aubertin, M. (2007). “A constitutive model to predict the hydromechanical behavior of rock joints.” Proc., 60th Canadian Geotechnical Conf., GeoOttawa2007, Ottawa, Canada, 2011–2018.
Wang, J. A., and Park, H. D. (2001). “Comprehensive prediction of rockburst based on analysis of strain energy in rocks.” Tunnelling Underground Space Technol., 16(1), 49–57.
Wang, P., et al. (2010). “The stress incremental forecasting method of rock burst. Meitan Xuebao.” J. China Coal Soc., 35, 5–9.
Wang, X. B. (2006). “Shear deformation, failure and instability of rock specimen in uniaxial compression based on gradient-dependent plasticity.” GeoShanghai Int. Conf., Geotechnical special publication, 150, ASCE, Reston, VA, 213–219.
Wawersik, W. R., and Fairhurst, C. (1970). “A study of brittle rock fracture in laboratory compression experiments.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 7(5), 561–564.
Whyatt, J. K., Blake, W., Williams, T. J., and White, B. G. (2002). “60 years of rockbursting in the Coeur D’Alene District of Northeastern Idaho, USA: Lessons learned and remaining issues.” Proc., 109th Annual Exhibit and Meeting, Society for Mining, Metallurgy, and Exploration, Preprint 02-164, Phoenix, AZ, 1–10.
Wiles, T. D. (2005). “Rockburst prediction using numerical modelling: Realistic limits for failure prediction accuracy.” Controlling seismic risk, rockbursts and seismicity in mines, Y. Potvin and M. Hudyma, eds., Australian Center for Geomechanics, Nedlands, Australia, 57–63.
Wu, Y., and Zhang, W. (1997). “Evaluation of the bursting proneness of coal by means of its failure duration.” Rockbursts and seismicity in mines, S. J. Gibowicz and S. Lasocki, A.A. Balkema, Rotterdam, Netherlands.
Yagiz, S. (2009). “Assessment of brittleness using rock strength and density with punch penetration test.” Tunnelling Underground Space Technol., 24(1), 66–74.
Yi, X., and Kaiser, P. K. (1993). “Mechanisms of rockmass failure and prevention strategies in rockburst conditions.” Rockbursts and seismicity in mines, A.A. Balkema, Rotterdam, Netherlands, 141–145.
Zhang, L., and Wang, Z. (2006). “Rock failure under unloading conditions and application for rock burst, soil and rock behavior and modeling.” Proc., GeoShanghai Int. Conf. 2006, Geotechnical special publication, 150, ASCE, Reston, VA, 235–240.
Information & Authors
Information
Published In
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Jul 20, 2016
Accepted: Sep 19, 2017
Published online: Dec 29, 2017
Published in print: Mar 1, 2018
Discussion open until: May 29, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.