Improved Nonlinear Strength Criterion for Jointed Rock Masses Subject to Complex Stress States
Publication: International Journal of Geomechanics
Volume 18, Issue 3
Abstract
Prediction of rock mass strength is important for estimating stability in rock engineering projects. In this paper, a novel strength criterion was proposed to determine the strength of a jointed rock mass subjected to a complex stress state. First, a series of tests were carried out on specimens with different joint geometries and under different confining pressures. From these tests, the factors affecting the strength of the jointed rock mass were obtained. The experimental results showed that normalized strength decreases initially and then increases as joint inclination angle increases, and it increases consistently and nonlinearly with increasing normalized confining pressure. Based on the experimental results, an improved nonlinear strength criterion was presented to describe the combined influence of the two aforementioned factors on jointed rock mass strength, and methods for determining the involved parameters were also introduced. Furthermore, multiaxial test data from the literature and biaxial test data from this paper were used to validate the feasibility and reliability of the new criterion. The results showed that the new criterion can predict the strength of jointed rock with high accuracy.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the National Nature Science Foundation of China (Grant 41602324) and National Basic Research Program of China (973 Program) (Grant 2014CB046904 and 2015CB058102).
References
Alejano, L. R., and Bobet, A. (2012). “Drucker–Prager criterion.” Rock Mech. Rock Eng., 45(6), 995–999.
Chang, C., and Haimson, B. (2012). “A failure criterion for rocks based on true triaxial testing.” Rock Mech. Rock Eng., 45(6), 1007–1010.
da Fontoura, S. A. (2012). “Lade and modified Lade 3D rock strength criteria.” Rock Mech. Rock Eng., 45(6), 1001–1006.
Dinc, O. S., Sonmez, H., Tunusluoglu, C., and Kasapoglu, K. E. (2011). “A new general empirical approach for the prediction of rock mass strengths of soft to hard rock masses.” Int. J. Rock Mech. Min. Sci., 48(4), 650–665.
Eberhardt, E. (2012). “The Hoek–Brown failure criterion.” Rock Mech. Rock Eng., 45(6), 981–988.
Haimson, B., and Bobet, A. (2012). “Introduction to suggested methods for failure criteria.” Rock Mech. Rock Eng., 45(6), 973–974.
He, P., Kulatilake, P., Liu, D., and He, M. (2017). “Development of new three-dimensional coal mass strength criterion.” Int. J. Geomech., 1–20.
Hoek, E., and Brown, E. T. (1980). “Empirical strength criterion for rock masses.” J. Geotech. Eng. Div., 106(9), 1013–1035.
Hoek, E., Wood, D., and Shah, S. (1992). “A modified Hoek–Brown criterion for jointed rock masses.” J. Hudson, ed., Proc., Rock Characterization Symposium, International Society for Rock Mechanics, Lisbon, Portugal, 209–213.
Jiang, H., and Zhao, J. (2015). “A simple three-dimensional failure criterion for rocks based on the Hoek–Brown criterion.” Rock Mech. Rock Eng., 48(5), 1807–1819.
Kulatilake, P., Park, J., and Malama, B. (2006). “A new rock mass failure criterion for biaxial loading conditions.” Geotech. Geol. Eng., 24(4), 871–888.
Labuz, J. F., and Zang, A. (2012). “Mohr–Coulomb failure criterion.” Rock Mech. Rock Eng., 45(6), 975–979.
Lu, D., Ma, C., Du, X., and Gong, Q. (2017). “Development of a new nonlinear unified strength theory for geomaterials based on the characteristic stress concept.” Int. J. Geomech., 1–11.
Melkoumian, N., Priest, S., and Hunt, S. P. (2009). “Further development of the three-dimensional Hoek–Brown yield criterion.” Rock Mech. Rock Eng., 42(6), 835–847.
Priest, S. (2012). “Three-dimensional failure criteria based on the Hoek–Brown criterion.” Rock Mech. Rock Eng., 45(6), 989–993.
Rafiai, H. (2011). “New empirical polyaxial criterion for rock strength.” Int. J. Rock Mech. Min. Sci., 48(6), 922–931.
Ramamurthy, T., and Arora, V. K. (1994). “Strength prediction for jointed rocks in confined and unconfined states.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 31(1), 9–22.
Saeidi, O., Rasouli, V., Vaneghi, R. G., Gholami, R., and Torabi, S. R. (2014). “A modified failure criterion for transversely isotropic rocks.” Geosci. Front., 5(2), 215–225.
Saroglou, H., and Tsiambaos, G. (2008). “A modified Hoek-Brown failure criterion for anisotropic intact rock.” Int. J. Rock Mech. Min. Sci., 45(2), 223–234.
Singh, M. (1997). “Engineering behaviour of jointed model materials.” Ph.D. thesis, Indian Institute of Technology, New Delhi, India.
Singh, M., and Rao, K. S. (2005). “Empirical methods to estimate the strength of jointed rock masses.” Eng. Geol., 77(1), 127–137.
Singh, M., Samadhiya, N. K., Kumar, A., Kumar, V., and Singh, B. (2015). “A nonlinear criterion for triaxial strength of inherently anisotropic rocks.” Rock Mech. Rock Eng., 48(4), 1387–1405.
Singh, M., and Singh, B. (2012). “Modified Mohr-Coulomb criterion for non-linear triaxial and polyaxial strength of jointed rocks.” Int. J. Rock Mech. Min. Sci., 51, 43–52.
Tiwari, R. P., and Rao, K. S. (2006). “Post failure behaviour of a rock mass under the influence of triaxial and true triaxial confinement.” Eng. Geol., 84(3–4), 112–129.
Tiwari, R. P., and Rao, K. S. (2007). “Response of an anisotropic rock mass under polyaxial stress state.” J. Mater. Civ. Eng., 393–403.
Ulusay, R., and Hudson, J. A. (2012). “Suggested methods for rock failure criteria: General introduction.” Rock Mech. Rock Eng., 45(6), 971.
Yang, Y., Gao, F., and Lai, Y. (2013). “Modified Hoek–Brown criterion for nonlinear strength of frozen soil.” Cold Reg. Sci. Technol., 86, 98–103.
You, M. (2009). “True-triaxial strength criteria for rock.” Int. J. Rock Mech. Min. Sci., 46(1), 115–127.
Zhang, L. (2008). “A generalized three-dimensional Hoek–Brown strength criterion.” Rock Mech. Rock Eng., 41(6), 893–915.
Zhang, L., and Zhu, H. (2007). “Three-dimensional Hoek-Brown strength criterion for rocks.” J. Geotech. Geoenviron. Eng., 1128–1135.
Zhang, Q., Wang, S., Ge, X., and Wang, H. (2010). “Modified Mohr-Coulomb strength criterion considering rock mass intrinsic material strength factorization.” Min. Sci. Techol., 20(5), 701–706.
Zhang, Q., Zhu, H., and Zhang, L. (2013). “Modification of a generalized three-dimensional Hoek–Brown strength criterion.” Int. J. Rock Mech. Min. Sci., 59, 80–96.
Zhu, H., Wu, W., Chen, J., Ma, G., Liu, X., and Zhuang, X. (2016). “Integration of three dimensional discontinuous deformation analysis (DDA) with binocular photogrammetry for stability analysis of tunnels in blocky rockmass.” Tunnelling Underground Space Technol., 51, 30–40.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 18 • Issue 3 • March 2018
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Mar 3, 2017
Accepted: Sep 7, 2017
Published online: Dec 29, 2017
Published in print: Mar 1, 2018
Discussion open until: May 29, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.