Numerical Investigation of the Circumferential Stresses around Boreholes during Horizontal Directional Drilling
Publication: International Journal of Geomechanics
Volume 17, Issue 12
Abstract
Borehole stability during horizontal directional drilling is one of the most important issues affecting success of pipe installations using this technique under roads, railways, and other obstructions. Two failure mechanisms, shear failure (blow-out) and tensile fracture (hydrofracture), have previously been identified. Both failure mechanisms can be seen in saturated clay based on total stress analysis, and shear failure dominates in dry sand based on effective stress analysis. Numerical modeling was used to investigate these failure mechanisms, and parametric studies were implemented. It was found that changes of elastic moduli and dilation angles have a minor impact on the numerical results when linear elastic analysis up to the initiation of yielding is undertaken. It was also found that the numerical results at the crown (and invert) can deviate from the theoretical results if yielding occurs at the shoulder (and haunch) of horizontal boreholes. Linear regression analysis was used to approximate these deviations. It was concluded that the ratios of intercepts of linear regression lines and vertical stresses are related to the undrained shear strength of clay and the critical friction angle of sand. However, there are no obvious relationships between the slopes of the linear regression lines and other factors. The ranges for coefficients in the modified solution are given.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was funded by a Discovery Grant to the second author awarded by the Natural Sciences and Engineering Research Council of Canada.
References
Abaqus [Computer software]. Abaqus, Providence, RI.
ADINA [Computer software]. ADINA R & D, Watertown, MA.
Alfaro, M. C., and Wong, R. C. K. (2001). “Laboratory studies on fracturing of low-permeability soils.” Can. Geotech. J., 38(2), 303–315.
Arends, G. (2003). “Need and possibilities for a quality push within the technique of horizontal directional drilling (HDD).” Proc., 2003 No-Dig Conf., North American Society for Trenchless Technology (NASTT), Cleveland, Paper No. 36.
Ariaratnam, S. T., Harbin, B. C., and Stauber, R. L. (2007). “Modeling of annular fluid pressures in horizontal boring.” Tunnelling Underground Space Technol., 22(5–6), 610–619.
Baumert, M. E., Allouche, E. N., and Moore, I. D. (2005). “Drilling fluid considerations in design of engineered horizontal directional drilling installations.” Int. J. Geomech., 339–349.
Bennet, D., and Wallin, K. (2008). “Step by step evaluation of hydrofracture risks for horizontal directional drilling projects.” Proc., International Pipeline Conf. 2008, ASCE, Reston, VA, 1–10.
Carlos, A. L., Lillian, D. W., and Patrick, J. C. (2002). “Guidelines for installation of utilities beneath corps of engineers levees using horizontal directional drilling.” ERDC/GSL TR-02-09, U.S. Army Corps of Engineers Research and Development Center, Vicksburg, MS.
Carter, J. P., and Balaam, N. P. (1995). AFENA users manual, Centre for Geotechnical Research, Dept. of Civil Engineering, Univ. of Sydney, Sydney, Australia.
Carter, J. P., Booker, J. R., and Yeung, S. K. (1986). “Cavity expansion in cohesive frictional soils.” Géotechnique, 36(3), 349–358.
Carter, J. P., Randolph, M. F., and Wroth, C. P. (1979). “Stress and pore pressure changes in clay during and after the expansion of a cylindrical cavity.” Int. J. Numer. Anal. Methods Geomech., 3(4), 305–322.
Collins, I. F., Pender, M. J., and Yan, W. (1992). “Cavity expansion in sands under drained loading conditions.” Int. J. Numer. Anal. Methods Geomech., 16(1), 3–23.
Elwood, D. E. Y., Moore, I. D., and Xia, H. (2007). “Hydraulic fracture experiments in a frictional material and approximations for maximum allowable mud pressure.” Proc., 60th Canadian Geotechnical Society Annual Conf., The Canadian Geotechnical Society, Richmond, British Columbia, Canada, pp. 1681–1688.
Kennedy, M. J. (2004). “Finite element calculations of hydraulic fracturing during horizontal directional drilling.” Master of science thesis, Queen’s Univ., Kingston, ON, Canada.
Kennedy, M. J., Moore, I. D., and Skinner, G. D. (2006). “Development of tensile hoop stress during horizontal directional drilling through sand.” Int. J. Geomech., 367–373.
Kennedy, M. J., Skinner, G. D., and Moore, I. D. (2004a). “Elastic calculations of limiting mud pressures to control hydro-fracturing during HDD.” Proc., 2004 No-Dig Conf., North American Society for Trenchless Technology (NASTT), Cleveland.
Kennedy, M. J., Skinner, G. D., and Moore, I. D. (2004b). “Limiting drilling slurry pressures to control hydraulic fracturing during HDD through purely cohesive soil.” Proc., 57th Canadian Geotechnical Conf., The Canadian Geotechnical Society, Richmond, British Columbia, Canada, 37–44.
Kirsch, G. (1898). Die theorie der elastizität und die bedürfnisse der festigkeitslehre, Springer, Berlin.
Kodikara, J. K., and Moore, I. D. (1993). “Axial response of tapered piles in cohesive frictional ground.” J. Geotech. Eng., 675–693.
Lan, H., and Moore, I. D. (2016). “Practical criteria for borehole instability in saturated clay during horizontal directional drilling (TM2–T2-01).” Proc., 2016 No-Dig Conf., North American Society for Trenchless Technology (NASTT), Cleveland.
Luger, H. J., and Hergarden, H. J. A. M. (1988). “Directional drilling in soft soil; influence of mud pressures.” Proc., 1988 No-Dig Conf., North American Society for Trenchless Technology (NASTT), Cleveland.
Marchi, M., Gottardi, G., and Soga, K. (2014). “Fracturing pressure in clay.” J. Geotech. Geoenviron. Eng., 04013008.
Mathew, F., and James, K. (2003). “Management of heave and subsidence risk for horizontal directional drilling.” Proc., 2003 No-Dig Conf., North American Society for Trenchless Technology (NASTT), Cleveland.
Mitchell, J. K., and Soga, K. (2005). Fundamentals of soil behavior, 3rd Ed., John Wiley and Sons, New York.
Neher, M. (2013). “HDD hydrofracture: Roots of the model we use (but don’t understand).” Proc., North American Society for Trenchless Technology 2013 No-Dig Show, North American Society for Trenchless Technology (NASTT), Cleveland.
Potts, D. M. (2003). “Numerical analysis: A virtual dream or practical reality.” Géotechniqiue, 53(6), 535–573.
Randolph, M. F., and Wroth, C. P. (1979). “An analytical solution for the consolidation around a driven pile.” Int. J. Numer. Anal. Methods Geomech., 3(3), 217–229.
Roy, M., Blanchet, R., Tavenas, F., and Rochelle, P. L. (1981). “Behaviour of a sensitive clay during pile driving.” Can. Geotech. J., 18(1), 67–85.
Roy, M., Tremblay, M., Tavenas, F., and Rochelle, P. L. (1982). “Development of pore pressures in quasi-static penetration tests in sensitive clay.” Can. Geotech. J., 19(2), 124–138.
Shen, S. L., Miura, N., and Koga, H. (2003). “Interaction mechanism between deep mixing column and surrounding clay during installation.” Can. Geotech. J., 40(2), 293–307.
Staheli, K., Bennett, R. D., O’Donnell, H. W., and Hurley, T. J. (1998). “Installation of pipelines beneath levees using horizontal directional drilling.” Report TR CPAR-GL-98-1, Geotechnical Laboratory (U.S.) Engineer Research and Development Center, U.S. Army Corps of Engineers Waterways Experiment Station, Vicksburg, MS.
Staheli, K., Price, C. G., and Wetter, L. (2010). “Effectiveness of hydrofracture prediction for HDD design.” Proc., 2010 No-Dig Conf., North American Society for Trenchless Technology (NASTT), Cleveland.
Timoshenko, S. P., and Goodier, J. N. (1951). Theory of elasticity, McGraw-Hill, New York.
Vesic, A. S. (1972). “Expansion of cavities in infinite soil mass.” J. Soil Mech. Found. Div., 98(3), 265–290.
Wallin, K., Walling, M., and Bennett, D. (2010). “HDD crossing under environmentally sensitive slough: Mitigation of hydrofracture risk.” Proc., 2010 No-Dig Conf., North American Society for Trenchless Technology (NASTT), Cleveland.
Wang, X., and Sterling, R. (2007). “Stability analysis of a borehole wall during horizontal directional drilling.” Tunnelling Underground Space Technol., 22(5), 620–632.
Xia, H. (2008). “Investigation of maximum allowable mud pressure within sand and clay during horizontal directional drilling.” Ph.D. thesis, Queen’s Univ., Kingston, ON, Canada.
Xia, H., and Moore, I. D. (2006). “Estimation of maximum mud pressure in purely cohesive material during directional drilling.” Geomech. GeoEng., 1(1), 3–11.
Yu, H. (1990). “Cavity expansion theory and its application to the analysis of pressuremeters.” Ph.D. thesis, Oxford Univ., Oxford, England.
Yu, H. (2000). Cavity expansion methods in geomechanics, Kluwer Academic Publishers, Dordrecht, Netherland.
Yu, H., and Houlsby, G. T. (1995). “A large strain analytical solution for cavity contraction in dilatant soils.” Int. J. Numer. Anal. Methods Geomech., 19(11), 793–811.
Zhou, H., Kong, G., and Liu, H. (2016). “A semi-analytical solution for cylindrical cavity expansion in elastic–perfectly plastic soil under biaxial in situ stress field.” Géotechnique, 66(7), 584–595.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 17 • Issue 12 • December 2017
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Nov 17, 2016
Accepted: Jun 5, 2017
Published online: Sep 29, 2017
Published in print: Dec 1, 2017
Discussion open until: Mar 1, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.