Bearing Capacity of Foundations with Inclusion of Dense Sand Layer over Loose Sand Strata
Publication: International Journal of Geomechanics
Volume 17, Issue 10
Abstract
The lower- and upper-bound finite-element limit analysis in conjunction with second-order conic programming (SOCP) was used to estimate the ultimate bearing capacity of strip and circular footings with an inclusion of a layer of dense sand over existing loose sand strata. The analysis followed the Mohr-Coulomb yield criterion and an associated flow rule. The results are expressed in terms of an efficiency factor that increases quite significantly with increases in the (1) thickness and (2) friction angle of the upper densified layer. While keeping the same thickness of the upper dense sand layer, the circular footing exhibits greater efficiency-factor values as compared to strip footing. The numerical results compare well with data available from the literature.
Get full access to this article
View all available purchase options and get full access to this article.
References
Bowles, J. E. (1977). Foundation analysis and design, McGraw-Hill, New York.
Burd, H. J., and Frydman, S. (1997). “Bearing capacity of plane-strain footings on layered soils.” Can. Geotech. J., 34(2), 241–253.
De Simone, P. (1985). “Bearing capacity of a circular footing on a Coulomb medium.” Proc., 5th Int. Conf. on Numerical Methods in Geomechanics, Vol. 2, CRC, Boca Raton, FL, 829–836.
Farah, C. A. (2004). “Ultimate bearing capacity of shallow foundations on layered soils.” M.Sc. thesis, Civil and Environmental Engineering, Concordia Univ., Quebec.
Georgiadis, M., and Michalopoulos, A. (1985). “Bearing capacity of gravity bases on layered soil.” J. Geotech. Eng., 712–729.
Hanna, A. M. (1981). “Foundations on strong sand overlying weak sand.” J. Geotech. Engrg. Div., 107(7), 915–927.
Hanna, A. M. (1982). “Bearing capacity of foundations on a weak sand layer overlying a strong deposit.” Can. Geotech. J., 19(3), 392–396.
Hanna, A. M. (1987). “Finite element analysis of footings on layered soils.” Math. Modell., 9(11), 813–819.
Hjiaj, M., Lyamin, A. V., and Sloan, S. W. (2005). “Numerical limit analysis solutions for the bearing capacity factor Ny.” Int. J. Solids Struct., 42(5), 1681–1704.
Kenny, M. J., and Andrawes, K. Z. (1997). “The bearing capacity of footings on a sand layer overlying soft clay.” Géotechnique, 47(2), 339–346.
Krabbenhøft, K., Lyamin, A. V., and Sloan, S. W. (2007). “Formulation and solution of some plasticity problems as conic programs.” Int. J. Solids Struct., 44(5), 1533–1549.
Krabbenhøft, K., Lyamin, A. V., and Sloan, S. W. (2008). “Three-dimensional Mohr-Coulomb limit analysis using semidefinite programming.” Int. J. Numer. Methods Eng., 24(11), 1107–1119.
Kumar, A., Ohri, M. L., and Bansal, R. K. (2007). “Bearing capacity tests of strip footings on reinforced layered soil.” Geotech. Geol. Eng., 25(2), 139–150.
Kumar, J., and Chakraborty, M. (2014). “Upper bound axisymmetric limit analysis using Mohr-Coulomb yield criterion, finite elements and linear optimization.” J. Eng. Mech., 06014012.
Kumar, J., and Chakraborty, M. (2015). “Bearing capacity of a circular foundation on layered sand–clay media.” Soils Found., 55(5), 1058–1068.
Kumar, J., and Khatri, V. N. (2008). “Effect of footing roughness on lower bound Nγ values.” Int. J. Geomech., 176–187.
Kumar, J., and Khatri, V. N. (2011). “Bearing capacity factors of circular foundations for a general c-ϕ soil using lower bound finite elements limit analysis.” Int. J. Numer. Anal. Methods Geomech., 35(3), 393–405, Wiley.
Kumar, J., and Mohapatra, D. (2017). “Lower-bound finite elements limit analysis for Hoek-Brown materials using semidefinite programming.” J. Eng. Mech., 04017077.
Lyamin, A. V. (1999). “Three-dimensional lower bound limit analysis using nonlinear programming.” Ph.D. thesis, Univ. of Newcastle, Callaghan, Australia.
Lyamin, A. V., and Sloan, S. W. (2002a). “Lower bound limit analysis using non-linear programming.” Int. J. Numer. Methods Eng., 55(5), 573–611.
Lyamin, A. V., and Sloan, S. W. (2002b). “Upper bound limit analysis using linear finite elements and non-linear programming.” Int. J. Numer. Anal. Methods Geomech., 26(2), 181–216.
Makrodimopoulos, A., and Martin, C. M. (2006). “Lower bound limit analysis of cohesive frictional materials using second-order cone programming.” Int. J. Numer. Methods Eng., 66(4), 604–634.
Makrodimopoulos, A., and Martin, C. M. (2007). “Upper bound limit analysis using simplex strain elements and second-order cone programming.” Int. J. Numer. Anal. Methods Geomech., 31(6), 835–865.
Martin, C. M. (2005). “Exact bearing capacity calculations using the method of characteristics.” Proc., 11th Conf. of IACMAG, Vol. 4, International Association for Computer Methods and Advances in Geomechanics, 441–450.
Meyerhof, G. G. (1974). “Ultimate bearing capacity of footings on sand layer overlying clay.” Can. Geotech. J., 11(2), 223–229.
Meyerhof, G. G., and Hanna, A. M. (1978). “Ultimate bearing capacity of foundations on layered soils under inclined load.” Can. Geotech. J., 15(4), 565–572.
Michalowski, R. L., and Shi, L. (1995). “Bearing capacity of footings over two-layer foundation soil.” J. Geotech. Engrg., 421–428.
Oda, M., and Win, S. (1990). “Ultimate bearing-capacity tests on sand with clay layer.” J. Geotech. Eng., 1902–1906.
Okamura, M., Takemura, J., and Kimura, T. (1998). “Bearing capacity predictions of sand overlying clay based on limit equilibrium methods.” Soils Found., 38(1), 181–194.
Optum G2 [Computer software]. Optum Computational Engineering, Copenhagen, Denmark.
Shiau, J. S., Lyamin, A. V., and Sloan, S. W. (2003). “Bearing capacity of a sand layer on clay by finite element limit analysis.” Can. Geotech. J., 40(5), 900–915.
Shoaei, M. D., Alkarni, A., Noorzaei, J., Jaafar, M. S., and Huat, B. B. K. (2012). “Review of available approaches for ultimate bearing capacity of two-layered soils.” J. Civ. Eng. Manage., 18(4), 469–482.
Sloan, S. W. (1988). “Lower bound limit analysis using finite elements and linear programming.” Int. J. Numer. Anal. Methods Geomech., 12(1), 61–77.
Sloan, S. W., and Kleeman, P. W. (1995). “Upper bound limit analysis using discontinuous velocity fields.” Comput Methods Appl. Mech. Eng., 127(1), 293–314.
Information & Authors
Information
Published In
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Aug 26, 2016
Accepted: Apr 28, 2017
Published online: Jul 21, 2017
Published in print: Oct 1, 2017
Discussion open until: Dec 21, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.