Influence of Particle Size and Gradation on the Stress-Dilatancy Behavior of Granular Materials during Drained Triaxial Compression
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: International Journal of Geomechanics
Volume 17, Issue 9
Abstract
This paper examines the potential influence of particle-size distribution on stress-dilatancy behavior of granular materials from the results of 35 conventional drained triaxial compression tests. Seven different grain-size distribution curves of two different materials (glass beads and Péribonka sand) in the range of 63–2,000 µm were tested at different normal pressures and initial relative densities. It was shown that for a given relative density and confining pressure, although shear strength and volumetric response of the tested materials were independent of the coefficient of uniformity, , in the investigated range, they were significantly influenced by the variation of the mean particle size, . On the basis of the triaxial test results, a correlation between the material constant of a modified stress-dilatancy equation and D50 of the tested materials was found. In addition, the coefficient of an equation, which was introduced as an experimental adjustment of the well-known stress-dilatancy equation, were fine-tuned to account for . A comparison of the predictions by the proposed empirical formulas with stress-dilatancy data from the literature and a micromechanical explanation of the experimental results are also provided.
Get full access to this article
View all available purchase options and get full access to this article.
References
Ahmed, S. M. (1972). “A study of the influence of confining pressure on the behaviour of sands.” M.Sc. dissertation, McGill Univ., Montreal, QC, Canada.
Al-Hussaini, M. (1983). “Effect of particle size and strain conditions on the strength of crushed basalt.” Can. Geotech. J., 20(4), 706–717.
Amirpour Harehdasht, S. (2016). “Influence of particle size and gradation on shear strength and dilation behavior of granular materials.” Ph.D. dissertation, Univ. de Sherbrooke, Sherbrooke, Canada.
Anthony, J. L., and Marone, C. (2005). “Influence of particle characteristics on granular friction.” J. Geophys. Res. B: Solid Earth, 110(B8), B08409.
ASTM. (2001a). “Standard test methods for laboratory compaction characteristics of soil using modified effort (56,000 ft-lbf/ft3, 2,700 kN-m/m3).” ASTM D 1557-00, West Conshohocken, PA.
ASTM. (2001b). “Standard test methods for maximum index density and unit weight of soils using a vibratory table.” ASTM D 4253-00, West Conshohocken, PA.
ASTM. (2001c). “Standard test methods for minimum index density and unit weight of soils and calculation of relative density.” ASTM D 4254-00, West Conshohocken, PA.
Been, K., and Jefferies, M. (1985). “A state parameter for sands.” Géotechnique, 35(2), 99–112.
Been, K., and Jefferies, M. (2004). “Stress dilatancy in very loose sand.” Can. Geotech. J., 41(5), 972–989.
Bishop, A. W. (1966). “The strength of soils as engineering materials.” Géotechnique, 16(2), 91–128.
Bishop, A. W., and Green, G. E. (1965). “The influence of end restraint on the compression strength of cohesionless soil.” Géotechnique, 15(3), 243–266.
Bolton, M. D. (1986). “The strength and dilatancy of sands.” Géotechnique, 36(1), 65–78.
Bowden, F. P., Moore, A. J. W., and Tabor, D. (1943). “The ploughing and adhesion of sliding metals.” J. Appl. Phys., 14(80), 80–91.
Casagrande, A. (1936). “Characteristics of cohesionless soils affecting the stability of slopes and earth fills.” J. Boston Soc. Civ. Eng., 23(1), 257–275.
Chakraborty, T., and Salgado, R. (2010). “Dilatancy and shear strength of sand at low confining pressures.” J. Geotech. Geoenviron. Eng., 527–532.
Collins, I. E., Pender, M. J., and Wang, Y. (1992). “Cavity expansion in sands under drained loading conditions.” Int. J. Numer. Anal. Methods Geomech., 16(1), 3–23.
Cornforth, D. H. (1961). “Plane strain failure characteristics of a saturated sand.” Ph.D. dissertation, Univ. of London, London.
De Josselin De Jong, G. (1976). “Rowe’s stress–dilatancy relation based on friction.” Géotechnique, 26(3), 527–534.
Goddard, J. D., and Didwania, A. K. (1998). “Computations of dilatancy and yield surfaces for assemblies of rigid frictional spheres.” Q. J. Mech. Appl. Math., 51(1), 15–44.
Gudehus, G. (1996). “A comprehensive constitutive equation for granular materials.” Soils Found., 36(1), 1–12.
Guo, P., and Su, X. (2007). “Shear strength, interparticle locking, and dilatancy of granular materials.” Can. Geotech. J., 44(5), 579–591.
Hall, E. B., and Gordon, B. B. (1963). “Triaxial testing using large scale high pressure equipment.” ASTM Symp., ASTM, West Conshohocken, PA, 361.
Herle, I., and Gudehus, G. (1999). “Determination of parameters of a hypoplastic constitutive model from properties of grain assemblies.” Mech. Cohesive-Frict. Mater., 4(5), 461–486.
Hanna, A. (2001). “Determination of plane-strain shear strength of sand from the results of triaxial tests.” Can. Geotech. J., 38(6), 1231–1240.
Houlsby, G. T. (1991). “How the dilatancy of soils affects their behaviour.” Proc., 10th European Conf. on Soil Mechanics and Foundation Engineering, Vol. 4, CRC, Boca Raton, FL, 1189–1202.
Hughes, J. M. O., Wroth, C. P., and Windle, D. (1977). “Pressuremeter test in sands.” Géotechnique, 27(4), 455–477.
Jefferies, M., and Shuttle, D. (2002). “Dilatancy in general Cambridge-type models.” Géotechnique, 52(9), 625–638.
Jewell, R. A. (1989). “Direct shear test on sand.” Géotechnique, 39(2), 309–322.
Jewell, R. A., and Wroth, C. P. (1987). “Direct shear tests on reinforced sand.” Géotechnique, 37(1), 53–68.
King, G. J. W., and Dickin, E. A. (1970). “Comparison of stress dilatancy theory.” J. Soil Mech. Found. Div., 96(5), 1697–1714.
Ladd, R. (1978). “Preparing test specimens using undercompaction.” Geotech. Test. J., 1(1), 16–23.
Lee, K. L., and Seed, H. (1967). “Drained strength characteristics of sands.” J. Soil Mech. Found. Div., 93(6), 117–141.
Li, X., and Dafalias, Y. F. (2000). “Dilatancy for cohesionless soils.” Géotechnique, 50(4), 449–460.
Li, X.-S., and Dafalias, Y. (2012). “Anisotropic critical state theory: Role of fabric.” J. Eng. Mech., 263–275.
Li, Y. R., Aydin, A., Xu, Q., and Chen, J. (2012). “Constitutive behavior of binary mixtures of kaolin and glass beads in direct shear.” KSCE J. Civ. Eng., 16(7), 1152–1159.
Mair, K., Frye, K. M., and Marone, C. (2002). “Influence of grain characteristics on the friction of granular shear zones.” J. Geophys. Res., 107(B10), 1–9.
Manzari, M. T., and Dafalias, Y. F. (1997). “A critical state two-surface plasticity model for sands.” Géotechnique, 47(2), 255–272.
Marsal, R. J. (1967). “Large scale testing of rockfill materials.” J. Soil Mech. Found. Div., 93(2), 27–43.
Molenkamp, F. (1981). “Elasto-plastic double hardening model Monot.” LGM Rep. CO-218595, Delft Geotechnic, Delft, Netherlands.
Morgan, J. (1999). “Numerical simulations of granular shear zones using the distinct element method: 2. Effects of particle size distribution and interparticle friction on mechanical behavior.” J. Geophys. Res., 104(B2), 2721–2732.
Mulilis, J. P., Arulanandan, K., Mitchell, J. K., Chan, C. K., and Seed, H. B. (1977). “Effects of sample preparation on sand liquefaction.” J. Geotech. Engrg. Div., 103(2), 91–108.
Muszynski, M. R. (2006). “Determination of maximum and minimum densities of poorly graded sands using a simplified method.” Geotech. Test. J., 29(3), 263–272.
Nakai, T. (1997). “Dilatancy characteristics of geomaterials.” Deformation and progressive failure in geomaterials, IS-Nagoya’97, A. Asaoka, T. Adachi, and F. Oda, eds., Pergamon, Oxford, U.K., 899–906.
Negussey, D., Wijewickreme, W. K. D., and Vaid, Y. P. (1988). “Constant volume friction angle of granular materials.” Can. Geotech. J., 25(1), 50–55.
Nemat-Nasser, S. (2000). “A micromechanically-based constitutive model for frictional deformation of granular materials.” J. Mech. Phys. Solids, 48(6–7), 1541–1563.
Newland, P. L., and Allely, B. H. (1957). “Volume changes in drained taixial tests on granular materials.” Géotechnique, 7(1), 17–34.
Nguyen, L., and Fatahi, B. (2016). “Behaviour of clay treated with cement & fibre while capturing cementation degradation and fibre failure–C3F Model.” Int. J. Plast., 81, 168–195.
Oda, M. (1972a). “The mechanism of fabric changes during compressional deformation of sand.” Soils Found., 12(2), 1–18.
Oda, M. (1972b). “Initial fabrics and their relations to mechanical properties of granular materials.” Soils Found., 12(1), 17–36.
Oda, M. (1976). “Fabric and their effects on the deformation behavior of sand.” Engineering Rep., Special Issue, Dept. of Foundation Engineering, Faculty of Engineering, Saitama Univ., Saitama, Japan.
Oda, M., and Iwashita, K. (1999). Mechanics of granular materials: An introduction, A. A. Balkema, Rotterdam, Netherlands.
Oda, M., and Kazama, H. (1998). “Microstructure of shear bands and its relation to the mechanisms of dilatancy and failure of dense granular soils.” Géotechnique, 48(4), 465–481.
Oda, M., and Konishi, J. (1974). “Microscopic deformation mechanism of granular material in simple shear.” Soils Found., 14(4), 25–38.
Pedley, M. J. (1990). “Experimental study of soil reinforcement interactions.” Ph.D. dissertation, Univ. of Oxford, Oxford, U.K.
Pradhan, T. B. S., Tatsuoka, F., and Sato, Y. (1989). “Experimental stress dilatancy relations of sand subjected to cyclic loading.” Soils Found., 29(1), 64.
Rowe, P. W. (1962). “The stress-dilatancy relation for static equilibrium of an assembly of particles in contact.” Proc. R. Soc. London Ser. A, 269(1339), 500–527.
Rowe, P. W., and Barden, L. (1966). “Importance of free ends in triaxial testing.” J. Soil Mech. Found. Div., 90(1), 1–27.
Sammis, C. G., King, G., and Biegel, R. (1987). “The kinematics of gouge deformation.” Pure Appl. Geophys., 125(5), 777–812.
Schofield, A. N., and Wroth, C. P. (1968). Critical state soil mechanics, McGraw-Hill, London.
Simoni, A., and Houlsby, G. T. (2006). “The direct shear strength and dilatancy of sand-gravel mixtures.” Geotech. Geol. Eng., 24(3), 523–549.
Taiebat, M., and Dafalias, Y. F. (2008). “SANISAND: Simple anisotropic sand plasticity model.” Int. J. Numer. Anal. Methods Geomech., 32(8), 915–948.
Tatsuoka, F., Nakamura, S., Huang, C. C., and Tani, K. (1990). “Strength anisotropy and shear band direction in plane strain tests of sand.” Soils Found., 30(1), 35–54.
Taylor, D. W. (1948). Fundamentals of soil mechanics, John Wiley & Sons, New York.
Vaid, Y. P., and Sasitharan, S. (1992). “The strength and dilatancy of sand.” Can. Geotech. J., 29(3), 522–526.
Vermeer, P. A., and de Borst, R. (1984). “Non-associated plasticity for soils, concrete and rock.” Heron, 29(3), 3–64.
Wan, R. G., and Guo, P. J. (1998). “A simple constitutive model for granular soils: Modified stress-dilatancy approach.” Comput. Geotech., 22(2), 109–133.
Wan, R. G., and Guo, P. J. (1999). “A pressure and density dependent dilatancy model for granular materials.” Soils Found., 39(6), 1–11.
Wan, R. G., and Guo, P. J. (2001). “Effect of microstructure on undrained behaviour of sands.” Can. Geotech. J., 38(1), 16–28.
Wan, R. G., and Guo, P. J. (2004). “Stress dilatancy and fabric dependencies on sand behavior.” J. Eng. Mech., 635–645.
Wu, P. K., Matsushima, K., and Tatsuoka, F. (2008). “Effects of specimen size and some other factors on the strength and deformation of granular soil in direct shear tests.” Geotech. Test. J., 31(1), 1–20.
Yoshimine, M., Ishihara, K., and Vargas, W. (1998). “Effects of principal stress direction and intermediate principal stress on undrained shear behavior of sand.” Soils Found., 38(3), 179–188.
Youd, T. L. (1973). “Factors controlling maximum and minimum densities of sands. Evaluation of relative density and its role in geotechnical projects involving cohesionless soils.” STP 523, ASTM, West Conshohocken, PA, 98–112.
Information & Authors
Information
Published In
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Aug 24, 2016
Accepted: Mar 1, 2017
Published online: Jun 27, 2017
Published in print: Sep 1, 2017
Discussion open until: Nov 27, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.