Three-Dimensional Failure Criteria for Rocks Based on the Hoek–Brown Criterion and a General Lode Dependence
Publication: International Journal of Geomechanics
Volume 17, Issue 8
Abstract
Three-dimensional (3D) failure criteria based on the Hoek–Brown (HB) criterion and a general Lode dependence for rocks were proposed in this paper. The proposed failure criteria inherited the compression meridian from the HB criterion and can include independent shear meridians to construct the failure envelop surface. Four failure criteria [Rubin-Willam-Warnke (RWW), Rubin-Pan-Hudson, R1.65, and Rubin λ (R)] with curved-triangular cross sections and two failure criteria with hexagonal cross sections (Rubin-Mohr-Coulomb and Rubin-Hoek-Brown) were shown as examples of applications of the general Lode dependence to demonstrate its versatility. The material parameters involved in the new failure criteria can be easily obtained from conventional triaxial compression (TXC) tests. Polyaxial compression (PXC) test data for six different rocks at a variety of stress states from published literatures were used to validate the proposed failure criteria, in which the best-fitting parameters obtained from the TXC tests were used to predict the rock failure in PXC states of stress. The comparison results demonstrated that three criteria (RWW, R1.65, and R) with similar cross section shapes gave better predictions than the other three criteria. One 3D failure criterion (R1.65) with an empirical factor (λ = 1.65) to define the independent shear meridian was considered to be the best among them because the RWW criterion tended to underestimate the strength for some rocks and the R criterion involved an extra parameter λ, which needed to be fitted from expensive PXC tests. The use of best-fitting parameters obtained from TXC tests can provide satisfactory predictions for rock failure with σ2 dependence using the R1.65 criterion.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by the National Natural Science Foundation of China (Grant No. 51308054) and the China Postdoctoral Science Foundation (Grant No.2012M510215). The author is also grateful to the anonymous reviewers for their helpful comments, which improved an early version of this paper.
References
Benz, T., and Schwab, R. (2008). “A quantitative comparison of six rock failure criteria.” Int. J. Rock Mech. Min. Sci., 45(7), 1176–1186.
Benz, T., Schwab, R., Kauther, R. A., and Vermeer, P. A. (2008). “A Hoek–Brown criterion with intrinsic material strength factorization.” Int. J. Rock Mech. Min. Sci., 45(2), 210–222.
Colmenares, L. B., and Zoback, M. D. (2002). “A statistical evaluation of intact rock failure criteria constrained by polyaxial test data for five different rocks.” Int. J. Rock Mech. Min. Sci., 39(6), 695–729.
Haimson, B. C., and Chang, C. (2000). “A new true triaxial cell for testing mechanical properties of rock, and its use to determine rock strength and deformability of Westerly granite.” Int. J. Rock Mech. Min. Sci., 37(1–2), 285–296.
Hoek, E., and Brown, E. T. (1980). “Empirical strength criterion for rock masses.” J. Geotech. Engng. Div., 106(GT9), 1013–1035.
Hoek, E., and Brown, E. T. (1997). “Practical estimates of rock mass strength.” Int. J. Rock Mech. Min. Sci., 34(8), 1165–1186.
Hoek, E., Carranza-Torres C., and Corkum B. (2002). “Hoek–Brown failure criterion–2002 edition.” Proc., 5th North American Rock Mechanics Symp. and 17th Tunneling. Assoc. of Canada Conf.: NARMS-TAC 2002, Mining Innovation and Technology, 2002 Ed., Hammah et al., eds., Toronto, 267–273.
Jiang, H., Wang, X. W., and Xie, Y. L. (2011). “New strength criteria for rocks under polyaxial compression.” Can. Geotech. J., 48(8), 1233–1245.
Jiang, H., and Xie, Y. (2011). “A note on the Mohr–Coulomb and Drucker–Prager strength criteria.” Mech. Res. Commun., 38(4), 309–314.
Jiang, H., and Xie, Y. L. (2012). “A new three-dimensional Hoek-Brown strength criterion.” Acta Mech. Sin., 28(2), 393–406.
Jiang, H., and Zhao, J. D. (2015). “A simple three-dimensional failure criterion for rocks based on the Hoek-Brown criterion.” Rock Mech. Rock Eng., 48(5), 1807–1819.
Lee, Y. K., Pietruszczak, S., and Choi, B. H. (2012). “Failure criteria for rocks based on smooth approximations to Mohr–Coulomb and Hoek–Brown failure functions.” Int. J. Rock Mech. Min. Sci., 56, 146–160.
LSTC (Livermore Software Technology Corporation). (2014). Keyword user’s manual Vol. II Material Models, LS-DYNA R7.1, Livermore, CA.
MATLAB [Computer software]. The MathWorks, Natick, MA.
Mogi, K. (1971). “Fracture and flow of rocks under high triaxial compression.” J Geophys. Res., 76(5), 1255–1269.
Mogi, K. (2007). Experimental rock mechanics, Taylor & Francis, London.
Ottosen, N. S. (1977). “A failure criterion for concrete.” J. Eng. Mech., 103(4), 527–535.
Pan, X. D., and Hudson, J. A. (1988). “A simplified three dimensional Hoek–Brown yield criterion.” Rock Mech. Power Plants, 95–103.
Rubin, M. (1991). “Simple, convenient isotropic failure surface.” J. Eng. Mech., 348–569.
Takahashi, M., and Koide, H. (1989). “Effect of the intermediate principal stress on strength and deformation behavior of sedimentary rocks at the depth shallower than 2000 m.” Rock at great depth, V. Maury and D. Fourmaintraux, eds., A.A. Balkema, Rotterdam, Netherlands, 19–26.
Willam, K. J., and Warnke, E. P. (1975). “Constitutive model for the triaxial behavior of concrete.” Proceedings of the International Association for Bridge and Structure Engineering, Seminar on Concrete Structure Subjected to Triaxial Stresses, Istituto Sperimentale Modelli e Strutture (ISMES), Bergamo, Italy, 1–30.
Zhang, L. (2008). “A generalized three-dimensional Hoek–Brown strength criterion.” Rock Mech. Rock Eng., 41(6), 893–915.
Zhang, L., and Zhu, H. (2007). “Three-dimensional Hoek–Brown strength criterion for rocks.” J. Geotech. Geoenviron. Eng., 1128–1135.
Information & Authors
Information
Published In
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Oct 27, 2015
Accepted: Dec 15, 2016
Published online: Feb 16, 2017
Discussion open until: Jul 16, 2017
Published in print: Aug 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.