Numerical Study of the Mechanical Behavior of Nonpersistent Jointed Rock Masses
Publication: International Journal of Geomechanics
Volume 16, Issue 1
Abstract
Estimating the mechanical properties of nonpersistent jointed rock masses is one of the most challenging problems in practical rock engineering due to the complex interaction of rock joints and intact-rock bridges. In this paper, the effect of joint geometrical parameters of nonpersistent rock mass on uniaxial compressive strength (UCS) and the deformation modulus was studied by using the discrete-element particle flow code PFC3D. In this numerical approach, the intact material is represented by an assembly of spherical particles bonded together at their contact points, and the joint interface is explicitly simulated by slip surfaces that are applied at contacts between the particles lying on the opposite sides of the joint interface. The failure process is simulated by the breakage of bonds between particles. A previous study of the authors has shown that this approach is capable of reproducing the mechanical behavior of nonpersistent jointed rock masses by a comparative study against physical experiments. In this study, the effect of joint geometrical parameters, including joint-orientation angle, spacing, persistency degree, step angle, and aperture, on the UCS and the deformation modulus was studied. To reduce the number of experiments and also gain a sound understanding of the effect of each parameter, experiments were designed using a well-established experiment design technique. Five failure modes were observed in the experiments, including intact failure, step path, block rotation, semiblock generation, and planar failure. It was found that the initiation and propagation of tensile cracks have a controlling effect on the observed failure modes. The and of jointed samples were analyzed using analysis of variance. It was found that joint-orientation angle, spacing, and persistency have a significant effect on both and and that joint-orientation angle has the greatest effect on the mechanical behavior of a rock mass.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors acknowledge Dr. Glenn Sharrock, Dr. Loren Lorig, Dr. Matthew Pierce, Dr. Xavier Garcia, and Dr. Diego Mas Ivars from Itasca Consulting Group for their invaluable technical support and comments.
References
Akram, M. S. (2010). “Physical and numerical investigation of conglomeratic rocks.” Ph.D. thesis, Univ. of New South Wales, Sydney, Australia.
Amadei, B., and Goodman, R. E. (1981). “A 3D constitutive relation for fractured rock masses.” Proc., Int. Symp. Mech. Behav. Struct. Media, Elsevier Scientific, Ottawa, 249–268.
Aydin, G., Karakurt, I., and Aydiner, K. (2013). “Prediction of the cut depth of granitic rocks machined by abrasive waterjet (AWJ).” Rock Mech. Rock Eng., 46(5), 1223–1235.
Bahaaddini, M., Hagan, P. C., Mitra, R., and Hebblewhite, B. K. (2014a). “Parametric study of smooth joint parameters on the shear behaviour of rock joints.” Rock Mech. Rock Eng., in press.
Bahaaddini, M., Hagan, P. C., Mitra, R., and Hebblewhite, B. K. (2014b). “Scale effect on the shear behaviour of rock joints based on a numerical study.” Eng. Geol., 181, 212–223 (Oct. 1, 2014).
Bahaaddini, M., Sharrock, G., and Hebblewhite, B. K. (2011a). “A comparison of physical and numerical experiments on artificial jointed rock masses using PFC3D.” Proc., 2nd Int. FLAC/DEM Symp., Itasca, Melbourne, VIC, Australia, 321–330.
Bahaaddini, M., Sharrock, G., and Hebblewhite, B. K. (2011b). “Synthetic rock mass modelling of a rock mass with non-persistent joints.” Proc., 35th APCOM Symp., Australasian Institute of Mining and Metallurgy (AusIMM), Wollongong, NSW, Australia, 615–624.
Bahaaddini, M., Sharrock, G., and Hebblewhite, B. K. (2013a). “Numerical direct shear tests to model the shear behaviour of rock joints.” Comput. Geotech., 51, 101–115.
Bahaaddini, M., Sharrock, G., and Hebblewhite, B. K. (2013b). “Numerical investigation of the effect of joint geometrical parameters on the mechanical properties of a non-persistent jointed rock mass under uniaxial compression.” Comput. Geotech., 49, 206–225.
Cording, E. J., and Jamil, S. M. (1994). “Slide geometries on rock slopes and walls.” Proc., 4th South Am. Congr. Rock Mech. ISRM, Santiago, Chile, 199–221.
Cundall, P. A. (2000). “Numerical experiments on rough joints in shear using a bonded particle model.” Proc., Aspects of Tectonic Faulting, Springer, Berlin, 1–9.
Devore, J. L. (2008). Probability and statistics for engineering and the sciences, Thomson Learning, Duxbury, MA.
Fakhimi, A., Riedel, J. J., and Labuz, J. F. (2006). “Shear banding in sandstone: Physical and numerical studies.” Int. J. Geomech., 185–194.
Huang, H., and Detournay, E. (2008). “Intrinsic length scales in tool-rock interaction.” Int. J. Geomech., 39–44.
Itasca Consulting Group. (2008). PFC3D manual, version 4.0, Itasca, Minneapolis.
Jade, S., and Sitharam, T. (2003). “Characterization of strength and deformation of jointed rock mass based on statistical analysis.” Int. J. Geomech., 43–54.
Jamil, S. M. (1992). “Strength of non-persistent rock joints.” Ph.D. thesis, Univ. of Illinois, Urbana, IL.
Jennings, J. E. (1970). “A mathematical theory for the calculation of the stability of open cast mines.” Proc., Symp. on Theor. Background to the Plann. of Open Pit Mines, A. A. Balkema, Johannesburg, 87–102.
Kim, B. H., Kaiser, P. K., and Grasselli, G. (2007). “Influence of persistence on behaviour of fractured rock masses.” Rock physics and geomechanics in the study of reservoirs and repositories, Geological Society, London, 161–173.
Lee, H., and Jeon, S. (2011). “An experimental and numerical study of fracture coalescence in pre-cracked specimens under uniaxial compression.” Int. J. Solids Struct., 48(6), 979–999.
Lobo-Guerrero, S., Vallejo, L., and Vesga, L. (2006). “Visualization of crushing evolution in granular materials under compression using DEM.” Int. J. Geomech., 195–200.
Mas Ivars, D. (2010). “Bonded particle model for jointed rock mass.” Ph.D. thesis, Univ. of KTH, Sweden 〈http://www.diva-portal.org/smash/record.jsf?pid=diva2%3A300557&dswid=-2764〉 (Mar. 29, 2015).
Mas Ivars, D., Pierce, M. E., Darcel, C., Reyes-Montes, J., Potyondy, D. O., Young, R. P., and Cundall, P. A. (2011). “The synthetic rock mass approach for jointed rock mass modelling.” Int. J. Rock Mech. Min. Sci., 48(2), 219–244.
Mendenhall, W., and Sincich, T. L. (1994). Statistics for engineering and the sciences, Prentice-Hall, Englewood Cliffs, NJ.
Mughieda, O. (1997). “Failure mechanisms and strength of non-persistent rock joints.” Ph.D. thesis, Univ. of Illinois, Urbana, IL.
Mughieda, O., and Alzo’ubi, A. K. (2004). “Fracture mechanisms of offset rock joints: A laboratory investigation.” Geotech. Geol. Eng., 22(4), 545–562.
Nemat-Nasser, S., and Horii, H. (1982). “Compression-induced nonplanar crack extension with application to splitting, exfoliation, and rockburst.” J. Geophys. Res., 87(B8), 6805–6821.
O’Sullivan, C. (2011). “Particle-based discrete element modeling: Geomechanics perspective.” Int. J. Geomech., 449–464.
Pierce, M., Cundall, P., Potyondy, D., and Mas Ivars, D. (2007). “A synthetic rock mass model for jointed rock.” Proc., 1st Canada-U.S. Rock Mech. Symp., Taylor & Francis, Vancouver, BC, Canada.
Potyondy, D. O., and Cundall, P. A. (2004). “A bonded-particle model for rock.” Int. J. Rock Mech. Min. Sci., 41(8), 1329–1364.
Prudencio, M. (2009). “Study of the strength and failure mode of rock mass with non-persistent joints.” Ph.D. thesis, Catholic Univ. of Chile, Santiago, Chile.
Prudencio, M., and Van-Sint-Jan, M. (2007). “Strength and failure modes of rock mass models with non-persistent joints.” Int. J. Rock Mech. Min. Sci., 44(6), 890–902.
Reyes, O., and Einstein, H. H. (1991). “Failure mechanisms of fractured rock-A fracture coalescence model.” Proc., 7th Int. Congr. Rock Mech., A. A. Balkema, Aachen, Germany, 333–340.
Ross, P. J. (1996). Taguchi techniques for quality engineering: Loss function, orthogonal experiments, parameter and tolerance design, McGraw-Hill Professional, NY.
Sharrock, G. B., Akram, M. S., and Mitra, R. (2009). “Application of synthetic rock mass modeling to estimate the strength of jointed sandstone.” Proc., 43rd U.S. Rock Mech. Symp. & 4th U.S.: Canada Rock Mech. Symp., American Rock Mechanics Association, Asheville, NC.
Shen, B., Stephansson, O., Einstein, H., and Ghahreman, B. (1995). “Coalescence of fractures under shear stresses in experiments.” J. Geophys. Res., 100(B4), 5975–5990.
Taguchi, G., and Konishi, S. (1987). Taguchi methods orthogonal arrays and linear graphs: Tools for quality engineering, American Supplier Institute, Dearborn, MI.
Tang, C. A., Lin, P., Wong, R. H. C., and Chau, K. T. (2001). “Analysis of crack coalescence in rock-like materials containing three flaws-Part II: Numerical approach.” Int. J. Rock Mech. Min. Sci., 38(7), 925–939.
Trivedi, A. (2013). “Estimating in situ deformation of rock masses using a hardening parameter and RQD.” Int. J. Geomech., 348–364.
Ulusay, R., and Hudson, J. A. (2007). The complete ISRM suggested methods for rock characterization, testing and monitoring: 1974–200, International Society of Rock Mechanics, Ankara, Turkey.
Van-Sint-Jan, M., and Prudencio, M. (2003). “Strength of model rock masses with discontinuous joints.” Proc., 11th Congr. Int. Soc. Rock Mech., South Africa Institute of Mining and Metallurgy, Johannesburg, South Africa, 1275–1279.
Wang, T. T., and Huang, T. H. (2009). “A constitutive model for the deformation of a rock mass containing sets of ubiquitous joints.” Int. J. Rock Mech. Min. Sci., 46(3), 521–530.
Wasantha, P. L. P., and Ranjith, P. G. (2013). “The Taguchi approach to the evaluation of the influence of different testing conditions on the mechanical properties of rock.” Environ. Earth Sci., 72(1), 1–11.
Wong, R. H. C., Chau, K. T., Tang, C. A., and Lin, P. (2001). “Analysis of crack coalescence in rock-like materials containing three flaws-Part I: Experimental approach.” Int. J. Rock Mech. Min. Sci., 38(7), 909–924.
Yang, S. Q., Yang, D. S., Jing, H. W., Li, Y. H., and Wang, S. Y. (2012). “An experimental study of the fracture coalescence behaviour of brittle sandstone specimens containing three fissures.” Rock Mech. Rock Eng., 45(4), 563–582.
Yang, W. H., and Tarng, Y. S. (1998). “Design optimization of cutting parameters for turning operations based on the Taguchi method.” J. Mater. Process. Technol., 84(1–3), 122–129.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 16 • Issue 1 • February 2016
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Apr 11, 2014
Accepted: Feb 21, 2015
Published online: Jun 18, 2015
Discussion open until: Nov 18, 2015
Published in print: Feb 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.