Rigid Spread Footings Resting on Soil Subjected to Axial Load and Biaxial Bending. II: Design Aids
Publication: International Journal of Geomechanics
Volume 13, Issue 2
Abstract
Design aids (nomograms) for rectangular and symmetrical trapezoidal rigid spread footings are developed using a method previously developed by the writers in a companion paper. The nomograms can be used by designers to directly determine their maximum axial load and biaxial moment capacities without exceeding the bearing capacity of the supporting soil. Three different types of pressure distribution at the soil-footing interface are considered: uniform, linear, and parabolic. The results obtained can then be compared with the biaxial moment-axial load interaction diagrams of the attached concrete walls or columns. This allows the structural designer to determine the vulnerability and likelihood of exceeding the bearing capacity of the supporting soil. Four examples are presented that show the effectiveness and simplicity of the proposed nomograms in the analysis of isolated rectangular and trapezoidal rigid spread footings resting on soil.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research presented in this paper was carried out at the National University of Colombia, School of Mines at Medellín. The writers want to express their appreciation to DIME for the financial support and to Dr. J. Paul Smith-Pardo and Mauricio Areiza-Hurtado, members of the Structural Stability Group of the National University of Colombia, for their suggestions.
References
Algin, H. M. (2000). “Stresses from linearly distributed pressures over rectangular areas.” Int. J. Numer. Anal. Methods Geomech., 24(8), 681–692.
Algin, H. M. (2007). “Practical formula for dimensioning a rectangular footing.” Eng. Structures, 2(6)9, 1128–1134.
Bouassida, M., Jellali, B., and Porbaha, A. (2009). “Limit analysis of rigid foundations on floating columns.” Int. J. Geomech., 9(3), 89–101.
Bowles, J. E. (1977). Foundation analysis and design, 3rd Ed., McGraw Hill, New York.
Das, B. M. (2009). Shallow foundations, 2nd Ed., CRC Press, Boca Raton, FL.
Gourvenec, S., Randolph, M. F., and Kingsnorth, O. (2006). “Undrained bearing capacity of square and rectangular footings.” Int. J. Geomech., 6(3), 147–157.
Gurfinkel, G. (1970). “Analysis of footings subjected to biaxial bending.” J. Struct. Div., 96(6), 1049–1059.
Hackman, M. (1977). “Bearing pressures on bridge footings.” Civ. Engrg., (11), 37–39.
Highter, W. H., and Anders, J. C. (1985).”Dimensioning footings subjected to eccentric loads.” J. Geotech. Engrg., 111(5), 659–665.
Houlsby, G. T., and Cassidy, M. J. (2002). “A plasticity model for the behaviour of footing on sand under combined loading.” Geotechnique, 53(2), 117–129.
Irles, R., and Irles, F. (1994). “Explicit stresses under rectangular footings.” J. Geotech. Engrg., 120(2), 444–450.
Jarquio, R. (2005). “Steel reinforcement for rectangular footing with biaxial bending.” Proc., Int. Conf. on Application of Codes, Design and Regulations, Institute of Civil Engineers, London, 609–616.
Jarquio, R, and Jarquio, V. (1983). “Design footing area with biaxial bending.” J. Geotech. Engrg., 109(10), 1337–1341.
Jarquio, R, and Jarquio, V. (1984). “Vertical stress formulas for triangular loading.” J. Geotech. Engrg., 110(1), 73–78.
Kramrisch, F. (1985). “Footings.” Chapter 5, Handbook of concrete engineering, 2nd Ed., M. Fintel, ed., Van Nostrand Reinhold Company, New York, 111–134.
Kumar, J., and Ghosh, P. (2007). “Ultimate bearing capacity of two interfering rough strip footings.” Int. J. Geomech., 7(1), 53–63.
Plock, H. J. (1963). “Fast way to find pressure under footings.” Eng. News Rec., 25, 50–51.
Rayhani, M. H. T., and El Naggar, M. H. (2008). “Numerical modeling of seismic response of rigid foundation on soft soil.” Int. J. Geomech., 8(6), 336–346.
Rodriguez, J. A., and Aristizabal-Ochoa, J. D. (1999). “Biaxial interaction diagrams for short R/C columns of any cross section.” J. Struct. Div., 125(6), 672–683.
Rodriguez-Gutierrez, J. A., and Aristizabal-Ochoa, J. D. (2013). “Rigid spread footings resting on soil subjected to axial load and biaxial bending. I: Simplified analytical method,” Int. J. Geomech., 13(2), 109–119.
Rozvany, G. I. N, and Adidam, S. R. (1971).“On circular footing slabs.” Building Sci., 6(2), 41–44.
Smith-Pardo, J. P. (2004). “Wall-frame structures with vulnerable foundations.” Ph.D. thesis, Purdue Univ., West Lafayette, IN.
Smith-Pardo, J. P. (2008). “Reinforced concrete walls with vulnerable foundations.” J. Geotech. Geoenviron. Eng., 134(2), 257–261.
Smith-Pardo, J. P., and Bobet, A. (2007). “Behavior of rigid footings on gravel under axial load and moment.” J. Geotech. Geoenviron. Eng., 133(10), 1203–1215.
Vitone, D. M., and Valsangkar, A. J. (1986a). “Rectangular foundations subjected to biaxial bending.” Civ. Engrg Pract. Design Eng., 9(5), 799–814.
Vitone, D. M., and Valsangkar, A. J. (1986b). “Stresses from loads over rectangular areas.” J. Geotech. Engrg., 112(10), 961–964.
Yamamoto, N., Randolph, M. F., and Einav, I. (2008). “Simple formulas for the response of shallow foundations on compressible sands.” Int. J. Geomech., 8(4), 230–239.
Zweig, A. (1966). “Eccentrically loaded trapezoidal or round footings.” J. Struct. Div., 92(1), 161–168.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jul 21, 2011
Accepted: Jan 30, 2012
Published online: Feb 2, 2012
Published in print: Apr 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.