Combined Impact of -Butanol Additive and Spark Timing on Combustion and Efficiency of a GDI Engine
Publication: Journal of Energy Engineering
Volume 145, Issue 5
Abstract
The influence of -butanol additive and spark timing on the combustion process was studied in a gasoline direct injection (GDI) engine, as well as fuel efficiency and relevant performance indicators. Three concentrations of -butanol blended fuels (i.e., Bu15, Bu30, and Bu50) were used as tested fuels and compared to regular gasoline at low and high loads. The results indicate that increasing the -butanol concentration or advanced spark timing can increase the combustion pressure and temperature, improve the burning rate, and reduce combustion duration. Moreover, brake thermal efficiency (BTE) increases with rising -butanol concentration, but its change with spark timing is affected by -butanol concentration. At the low load, the highest BTE with regular gasoline and Bu15 occurs between varying spark timing with advanced spark timing, while BTE reduces persistently for Bu30 and Bu50. At the high load, furthermore, BTE increases for all the tested fuels with advanced spark timing. However, increasing -butanol concentration or advanced spark timing may increase knock tendency. To summarize, varying spark timing or -butanol concentration can affect the combustion process and fuel efficiency distinctly depending on fuel properties and engine loads. Spark timing should be adjusted to achieve better fuel efficiency for high concentration of -butanol blended fuels.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was funded by the National Natural Science Foundation of China (Grant No. 51006032), the Fundamental Research Funds for the Central Universities, Hunan University and Key Laboratory of Shaanxi Province for Development and Application of New Transportation Energy (Grant No. 300102229512).
References
Chen, B. L., X. L. Liu, H. F. Liu, H. Wang, D. C. Kyritsis, and M. F. Yao. 2017a. “Soot reduction effects of the addition of four butanol isomers on partially premixed flames of diesel surrogates.” Combust. Flame 177 (Mar): 123–136. https://doi.org/10.1016/j.combustflame.2016.12.012.
Chen, Z., J. P. Liu, Z. Y. Han, B. Du, and Y. Liu. 2013. “Study on performance and emissions of a passenger-car diesel engine fueled with butanol-diesel blends.” Energy 55 (1): 638–646. https://doi.org/10.1016/j.energy.2013.03.054.
Chen, Z., B. Y. Xu, F. Zhang, and J. P. Liu. 2017b. “Quantitative research on thermodynamic process and efficiency of a LNG heavy-duty engine with high compression ratio and hydrogen enrichment.” Appl. Therm. Eng. 125 (Oct): 1103–1113. https://doi.org/10.1016/j.applthermaleng.2017.07.102.
Chen, Z., F. Yang, S. Xue, Z. K. Wu, and J. P. Liu. 2015. “Impact of higher n-butanol addition on combustion and performance of GDI engine in stoichiometric combustion.” Energy Convers. Manage. 106 (Dec): 385–392. https://doi.org/10.1016/j.enconman.2015.09.051.
Chen, Z., Y. Q. Zhang, X. T. Wei, Q. C. Zhang, and Z. K. Wu. 2017c. “Thermodynamic process and performance of high n-butanol/gasoline blends fired in a GDI production engine running wide-open throttle (WOT).” Energy Convers. Manage. 152 (Nov): 57–64. https://doi.org/10.1016/j.enconman.2017.09.037.
Dhamodaran, G., G. S. Esakkimuthu, Y. K. Pochareddy, and H. Sivasubramanian. 2017. “Investigation of n-butanol as fuel in a four-cylinder MPFI SI engine.” Energy 125 (Apr): 726–735. https://doi.org/10.1016/j.energy.2017.02.134.
Dürre, P. 2011. “Fermentative production of butanol—The academic perspective.” Curr. Opin. Biotechnol. 22 (3): 331–336. https://doi.org/10.1016/j.copbio.2011.04.010.
Elfasakhany, A. 2016. “Experimental study of dual n-butanol and iso-butanol additives on spark-ignition engine performance and emissions.” Fuel 163 (Jan): 166–174. https://doi.org/10.1016/j.fuel.2015.09.059.
Elfasakhany, A. 2017. “Investigations on performance and pollutant emissions of spark-ignition engines fueled with n-butanol–, isobutanol–, ethanol–, methanol–, and acetone–gasoline blends: A comparative study.” Renewable Sustainable Energy Rev. 71 (May): 404–413. https://doi.org/10.1016/j.rser.2016.12.070.
Feng, H. Q., D. J. Liu, X. X. Yang, M. An, and W. W. Zhang. 2016. “Availability analysis of using iso-octane/n-butanol blends in spark-ignition engines.” Renewable Energy 96 (Oct): 281–294. https://doi.org/10.1016/j.renene.2016.04.081.
Fournier, S., G. Simon, and P. Seers. 2016. “Evaluation of low concentrations of ethanol, butanol, BE, and ABE blended with gasoline in a direct-injection, spark-ignition engine.” Fuel 181 (Oct): 396–407. https://doi.org/10.1016/j.fuel.2016.04.135.
García, V., J. Päkkilä, H. Ojamo, E. Muurinen, and R. L. Keiski. 2011. “Challenges in biobutanol production: How to improve the efficiency?” Renewable Sustainable Energy Rev. 15 (2): 964–980. https://doi.org/10.1016/j.rser.2010.11.008.
Green, E. M. 2011. “Fermentative production of butanol—The industrial perspective.” Curr. Opin. Biotechnol. 22 (3): 337–343. https://doi.org/10.1016/j.copbio.2011.02.004.
Han, X. Y., Z. Y. Yang, M. P. Wang, J. Tjong, and M. Zheng. 2017. “Clean combustion of n-butanol as a next generation biofuel for diesel engines.” Appl. Energy 198 (Jul): 347–359. https://doi.org/10.1016/j.apenergy.2016.12.059.
Hergueta, C., M. Bogarra, A. Tsolakis, A. Essa, and J. M. Herreros. 2017. “Butanol-gasoline blend and exhaust gas recirculation, impact on GDI engine emissions.” Fuel 208 (Nov): 662–672. https://doi.org/10.1016/j.fuel.2017.07.022.
Heywood, J. B. 1998. Internal combustion engine fundamentals. New York: McGraw-Hill.
Huang, H. Z., Q. S. Liu, Q. X. Wang, C. Z. Zhou, and C. L. Mo. 2016. “Experimental investigation of particle emissions under different EGR ratios on a diesel engine fueled by blends of diesel/gasoline/n-butanol.” Energy Convers. Manage. 121 (Aug): 212–223. https://doi.org/10.1016/j.enconman.2016.05.034.
Imdadul, H. K., H. H. Masjuki, M. A. Kalam, N. W. Zulkifli, and M. Kamruzzaman. 2017. “Evaluation of oxygenated n-butanol-biodiesel blends along with ethyl hexyl nitrate as cetane improver on diesel engine attributes.” J. Cleaner Prod. 141 (Jan): 928–939. https://doi.org/10.1016/j.jclepro.2016.09.140.
Irimescu, A., L. Marchitto, S. S. Merola, C. Tornatore, and G. Valentino. 2015. “Combustion process investigations in an optically accessible DISI engine fuelled with n-butanol during part load operation.” Renewable Energy 77 (May): 363–376. https://doi.org/10.1016/j.renene.2014.12.029.
Jin, C., M. F. Yao, H. F. Liu, C. F. Lee, and J. Ji. 2011. “Progress in the production and application of n-butanol as a biofuel.” Renewable Sustainable Energy Rev. 15 (8): 4080–4106. https://doi.org/10.1016/j.rser.2011.06.001.
Kumar, M., and K. Gayen. 2011. “Developments in biobutanol production: New insights.” Appl. Energy 88 (6): 1999–2012. https://doi.org/10.1016/j.apenergy.2010.12.055.
Lattimore, T., J. M. Herrerosa, H. M. Xu, and S. J. Shuai. 2016. “Investigation of compression ratio and fuel effect on combustion and PM emissions in a DISI engine.” Fuel 169 (Apr): 68–78. https://doi.org/10.1016/j.fuel.2015.10.044.
Li, Y., J. K. Gong, Y. W. Deng, W. H. Yuan, and J. Fu. 2017. “Experimental comparative study on combustion, performance and emissions characteristics of methanol, ethanol and butanol in a spark ignition engine.” Appl. Therm. Eng. 115 (Mar): 53–63. https://doi.org/10.1016/j.applthermaleng.2016.12.037.
Liang, B., Y. S. Ge, J. N. Tan, X. K. Han, and L. P. Gao. 2013. “Comparison of PM emissions from a gasoline direct injected (GDI) vehicle and a port fuel injected (PFI) vehicle measured by electrical low-pressure impactor (ELPI) with two fuels: Gasoline and M15 methanol gasoline.” J. Aerosol Sci. 57 (5): 22–31. https://doi.org/10.1016/j.jaerosci.2012.11.008.
Liu, H. F., P. Zhang, X. L. Liu, B. L. Chen, C. Geng, B. Li, H. Wang, Z. S. Li, and M. F. Yao. 2018. “Laser diagnostics and chemical kinetic analysis of PAHs and soot in co-flow partially premixed flames using diesel surrogate and oxygenated additives of n-butanol and DMF.” Combust. Flame 188 (Feb): 129–141. https://doi.org/10.1016/j.combustflame.2017.09.025.
Mack, J. H., D. Schuler, R. H. Butt, and R. W. Dibble. 2016. “Experimental investigation of butanol isomer combustion in homogeneous charge compression ignition (HCCI) engines.” Appl. Energy 165 (12): 612–626. https://doi.org/10.1016/j.apenergy.2015.12.105.
Moxey, B. G., A. Cairns, and H. Zhao. 2016. “A comparison of butanol and ethanol flame development in an optical spark ignition engine.” Fuel 170 (Apr): 27–38. https://doi.org/10.1016/j.fuel.2015.12.008.
Park, C., S. Lee, and U. Yi. 2016. “Effects of engine operating conditions on particle emissions of lean-burn gasoline direct-injection engine.” Energy 115 (Nov): 1148–1155. https://doi.org/10.1016/j.energy.2016.09.051.
Satsangi, D. P., and N. Tiwari. 2018. “Experimental investigation on combustion, noise, vibrations, performance and emissions characteristics of diesel/n-butanol blends driven genset engine.” Fuel 221 (Jun): 44–60. https://doi.org/10.1016/j.fuel.2018.02.060.
Sharudin, H., N. R. Abdullah, G. Najafi, R. Mamat, and H. H. Masjuki. 2017. “Investigation of the effects of iso-butanol additives on spark ignition.” Appl. Therm. Eng. 114 (Mar): 593–600. https://doi.org/10.1016/j.applthermaleng.2016.12.017.
Szwaja, S., and J. D. Naber. 2010. “Combustion of n-butanol in a spark-ignition IC engine.” Fuel 89 (7): 1573–1582. https://doi.org/10.1016/j.fuel.2009.08.043.
Tornatore, C., L. Marchitto, G. Valentino, F. E. Corcione, and S. S. Merola. 2012. “Optical diagnostics of the combustion process in a PFI SI boosted engine fueled with butanol-gasoline blend.” Energy 45 (1): 277–287. https://doi.org/10.1016/j.energy.2012.03.006.
Venugopal, T., and A. Ramesh. 2014. “Experimental studies on the effect of injection timing in a SI engine using dual injection of n-butanol and gasoline in the intake port.” Fuel 115 (1): 295–305. https://doi.org/10.1016/j.fuel.2013.07.013.
Wang, Y., X. M. Yu, Y. K. Ding, Y. D. Du, and Z. Chen. 2018. “Experimental comparative study on combustion and particle emission of n-butanol and gasoline adopting different injection approaches in a spark engine equipped with dual-injection system.” Fuel 211 (Jan): 837–849. https://doi.org/10.1016/j.fuel.2017.09.108.
Wei, H. Q., D. Q. Feng, J. Y. Pan, A. F. Shao, and M. Z. Pan. 2017. “Knock characteristics of SI engine fueled with n-butanol in combination with different EGR rate.” Energy 118 (Jan): 190–196. https://doi.org/10.1016/j.energy.2016.11.134.
Wei, H. Q., D. Q. Feng, M. Z. Pan, J. Y. Pan, and X. K. Rao. 2016. “Experimental investigation on the knocking combustion characteristics of n-butanol gasoline blends in a DISI engine.” Appl. Energy 175 (Aug): 346–355. https://doi.org/10.1016/j.apenergy.2016.05.029.
Zhang, B., C. W. Ji, and S. F. Wang. 2017. “Investigation on the lean combustion performance of a hydrogen-enriched n-butanol engine.” Energy Convers. Manage. 136 (Mar): 36–43. https://doi.org/10.1016/j.enconman.2016.12.065.
Zhang, Z. J., T. Y. Wang, M. Jia, Q. Wei, and X. Z. Meng. 2014. “Combustion and particle number emissions of a direct injection spark ignition engine operating on ethanol/gasoline and n-butanol/gasoline blends with exhaust gas recirculation.” Fuel 130 (6): 177–188. https://doi.org/10.1016/j.fuel.2014.04.052.
Zhao, F., M. C. Lai, and D. L. Harrington. 1999. “Automotive spark-ignited direct-injection gasoline engines.” Prog. Energy Combust. Sci. 25 (5): 437–562. https://doi.org/10.1016/S0360-1285(99)00004-0.
Zheng, Z. Q., X. F. Wang, X. F. Zhong, B. Hu, and H. F. Liu. 2016. “Experimental study on the combustion and emissions fueling biodiesel/n-butanol, biodiesel/ethanol and biodiesel/2, 5-dimethylfuran on a diesel engine.” Energy 115 (Nov): 539–549. https://doi.org/10.1016/j.energy.2016.09.054.
Information & Authors
Information
Published In
Journal of Energy Engineering
Volume 145 • Issue 5 • October 2019
Copyright
©2019 American Society of Civil Engineers.
History
Received: Aug 10, 2018
Accepted: Feb 6, 2019
Published online: Jul 19, 2019
Published in print: Oct 1, 2019
Discussion open until: Dec 19, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.