Modeling of Partially Shrouded Impellers’ Effect on Operating Efficiency and Flow Range of Centrifugal Compressor
Publication: Journal of Energy Engineering
Volume 142, Issue 4
Abstract
The centrifugal impeller is one of the most critical aerodynamic parts of centrifugal compressors. The previous experimental investigation demonstrated that the fully shrouded impeller is better in terms of efficiency whereas the unshrouded configuration is typical for wide flow range. To compromise between the high efficiency and wide flow range requirements, partially shrouded impellers have been developed, attaining reductions in the efficiency loss due to tip clearance while keeping a sufficient surge margin. However, the selection of the optimum shrouded percentage is influenced by several variables including stage efficiency, pressure losses coefficient, manufacturing cost, required power cost, resonance frequency, and stable operating range influenced. Hence, an optimization is required to compromise between these parameters to ensure better performance. This paper will introduce a new empirical approach to model the effect of shrouded percentage on these parameters which will help to specify the optimum configuration at an early preliminary design stage based on the sort of the application and according to the expected variation in the operating conditions. This model has been examined at high and very low flow coefficients and Mach numbers operating conditions, and the obtained parameters are compared with the computational fluid dynamics (CFD) simulation results and the recorded measured data in order to emphasize the validity of the new method. The conducted comparison revealed a good agreement between the obtained parameters by the new model and those derived numerically and experimentally with a maximum deviation of around . One of the main features of the developed method over the CFD approach is the fact that it does not require deep knowledge about the stage geometrical features; thus, it can be used in the early preliminary design process. Moreover, the included optimization emphasizes the need for a compromise decision in order to select the impeller configuration.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The first author would like to thank Petroleum Development Oman Company and Cranfield University for supporting this study.
References
Al-Busaidi, W., and Pilidis, P. (2015). “A new method for reliable performance prediction of multi-stage industrial centrifugal compressors based on stage stacking technique: Part II—New integrated model verification.” Appl. Therm. Eng., 90(1), 927–936.
Aungier, R. H. (1995). “Mean streamline aerodynamic performance analysis of centrifugal compressors.” J. Turbomach., 117(3), 360–366.
Casey, M., and Robinson, C. (2013). “A method to estimate the performance map of a centrifugal compressor stage.” J. Turbomach., 135(2), 021034.
Eckert, B., and Schnell, E. (1961). Axial- und Radial-Kompressoren, 2nd Ed., Springer, Heidelberg, 192–357.
Hao, K. Y., Wang, W. M., Shi, Y. Q., and Wang, S. S. (2011). “Effects of shroud curvature on the performance of centrifugal compressor blade.” Advanced Engineering Forum, Vol. 2, Trans Tech Publications, Switzerland, 700–705.
Lüdtke, K. H. (2004). Process centrifugal compressors, basics, function, operation, design, application, 1st Ed., Springer, Berlin.
Pampreen, R. C. (1973). “Small turbomachinery compressor and fan aerodynamics.” J. Eng. Gas Turbines Power, 95(3), 251–256.
Pfleiderer, C. (1961). Die Kreisel Pumpen, 5th Ed., Springer, Heidelberg.
Redlich, O., and Kwong, J. N. S. (1949). “On the thermodynamics of solutions. V: An equation of state. Fugacities of gaseous solutions.” Chem. Rev., 44(1), 233–244.
Sable, M. J., and Ramgir, M. S. (2006). Gas turbines and jet propulsion, 1st Ed., Technical Publications, Pune, India.
Senoo, Y., and Ishida, M. (1986). “Pressure loss due to the tip clearance of impeller blades in centrifugal and axial blowers.” J. Eng. Gas Turbines Power, 108(1), 32–37.
Seralathan, S., and Chowdhury, D. R. (2013). “Modification of centrifugal impeller and effect of impeller extended shrouds on centrifugal compressor performance.” Procedia Eng., 64(1), 1119–1128.
Sitaram, N., and Swamy, S. M. (2012). “Performance improvement of a centrifugal compressor by passive means.” Int. J. Rotating Mach., 2012, 9.
Sorokes, J. M. (2013). “Selecting a centrifugal compressor.” CEP Magazine, American Institute of Chemical Engineers (AIChE) and Dresser-Rand, New York.
Tang, J. (2006). “Computational analysis and optimization of real gas flow in small centrifugal compressors.” Acta Universitatis Lappeenrantaensis, 253, Lappeenranta Univ. of Technology, Lappeenranta, Finland.
Tang, J., Turunen-Saaresti, T., and Larjola, J. (2008). “Use of partially shrouded impeller in a small centrifugal compressor.” J. Therm. Sci., 17(1), 21–27.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Oct 2, 2015
Accepted: Dec 11, 2015
Published online: Feb 26, 2016
Discussion open until: Jul 26, 2016
Published in print: Dec 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.