Experimental Study of the New Bayonet Heat Exchanger
Publication: Journal of Energy Engineering
Volume 142, Issue 1
Abstract
An experimental study is conducted to investigate the heat transfer and the pressure drop properties of a single-phase flow in a bayonet tube heat exchanger. A bayonet tube heat exchanger has only one circulating fluid, i.e., tap water. The circulating fluid is supplied at an ambient temperature (cold medium) and, as a result, it will be heated by an electrical heater (heat source). The bayonet tube heat exchanger is a two-pass heat exchanger. Different experiments were performed to show the relationships and the effects of different parameters such as the Reynolds number, friction factor, Nusselt number, overall heat transfer coefficient, and effectiveness on the purposed heat exchanger. To enhance the heat transfer rates, a helical tape is installed in the annulus between the inner and outer tube. The flow is considered as turbulent in both the plain tube and the helical tape. The recorded Nusselt number for heat exchanger with the helical tape is about 35.6% higher than that without helical tape. In addition, the helical tape increased the effectiveness by approximately 30.2%.
Get full access to this article
View all available purchase options and get full access to this article.
References
ANSYS [Computer software]. Canonsburg, PA, Ansys.
Aquaro, D., Donatini, F., and Pieve, M. (2006). “Numerical and analytical analyses of a high temperature heat exchanger.” ASME 8th Biennial Conf. on Engineering Systems Design and Analysis, Vol. 4, Fatigue and Fracture, Heat Transfer, Internal Combustion Engines, Manufacturing, and Technology and Society, Torino, Italy.
Jolly, A. J., O’Doherty, T., and Bates, C. J. (1998). “A computer model for solving the thermal energy exchange in an ultra-high temperature heat exchanger. Part A: Computational theory.” Appl. Therm. Eng. 18(12), 1263–1276.
Kline, S. J., and McClintock, F. A. (1953). “Describing uncertainties in single-sample experiments.” Mech. Eng. 75(1), 3–8.
Lin, M., Wang, Q. W., and Guo, Z. X. (2012). “A simple method for predicting bulk temperature from tube wall temperature with uniform outside wall heat flux.” Int. Commun. Heat Mass Transfer, 39(5), 582–586.
Lock, G. S. H. (1992). The tubular thermosyphon, Oxford University Press, New York.
Ma, T., Zeng, M., Ji, Y. P., and Wang, Q. W. (2011a). “CFD optimization of gas-side flow channel configuration inside a high temperature bayonet tube heat exchanger with inner and outer fins.” ASME J. Eng. Gas Turbines Power, 133(12), 122–130.
Ma, T., Zeng, M., Ji, Y. P., and Wang, Q. W. (2011b). “Investigation of a novel bayonet tube high temperature heat exchanger with inner and outer fins.” Int. J. Hydrogen Energy, 36(5), 3757–3768.
Ma, T., Chen, Y. T., Zeng, M., and Wang, Q. W. (2012). “Stress analysis of internally finned bayonet tube in a high temperature heat exchanger.” Appl. Therm. Eng., 43, 101–108.
Minhas, H., and Lock, G. S. H. (1997). “Forced convection in an air-filled bayonet tube during the laminar-turbulent transition.” Heat Mass Transfer, 40(8), 1885–1894.
Nagarajan, V., Ponyavin, V., Chen, Y. T., Vernon, M. E., Pickard, P., and Hechanov, A. E. (2008). “Numerical study of sulfur trioxide decomposition in bayonet type heat exchanger and chemical decomposer with porous media zone and different packed bed designs.” Int. J. Hydrogen Energy, 33(22), 6445–6455.
Nagarajan, V., Ponyavin, V., Chen, Y. T., Vernon, M. E., Pickard, P., and Hechanov, A. E. (2009). “CFD modeling and experimental validation of sulfur trioxide decomposition in bayonet type heat exchanger and chemical decomposer for different packed bed designs.” Int. J. Hydrogen Energy, 34(6), 2543–2557.
O’Doherty, T., Jolly, A. J., and Bates, C. J. (2001a). “Analysis of a bayonet tube heat exchanger.” Appl. Therm. Eng., 21(1), 1–18.
O’Doherty, T., Jolly, A. J., and Bates, C. J. (2001b). “Optimization of heat transfer enhancement devices in a bayonet tube heat exchanger.” Appl. Therm. Eng., 21(1), 19–36.
Syed, K. S., Iqbal, Z., and Ishaq, M. (2011). “Optimal configuration of finned annulus in a double pipe with fully developed laminar flow.” Appl. Therm. Eng., 31(8–9), 1435–1446.
Ting, M., Zeng, M., Ji, Y. P., and Wang, Q. W. (2011) “CFD optimization of gas-side flowchannel configuration inside a high temperature bayonet tube heatexchanger with inner and outer fins.” J. Eng. Gas Turbines Power, 133, 853–861.
Wang, Q. W., Lin, M., and Zeng, M. (2009). “Effect of lateral fin profiles on turbulent flow and heat transfer performance of internally finned tubes.” Appl. Therm. Eng., 29(14–15), 3006–3013.
Zeng, M., Ma, T., Sundén, B., Trabia, M. B., and Wang, Q. (2013). “Effect of lateral fin profiles on stress performance of internally finned tubes in a high temperature heat exchanger.” Appl. Them. Eng., 50(1), 886–895.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Aug 28, 2014
Accepted: Mar 18, 2015
Published online: May 12, 2015
Discussion open until: Oct 12, 2015
Published in print: Mar 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.