Feasibility Study on Power Generation from Waste Plastics with Partial Precombustion Carbon Capture and Conversion
Publication: Journal of Energy Engineering
Volume 141, Issue 2
Abstract
The feasibility of upcycling waste plastics into concurrent production of carbon nanotubes (CNTs) and of a hydrogen-enriched gaseous hydrocarbon stream was shown to be possible in a continuous steady-state steady-flow process. The feedstock was post-consumer (waste) low-density polyethylene (LDPE), which was pyrolyticaly gasified at 800°C, in a flow of nitrogen carrier gas. The evolving gaseous hydrocarbon pyrolyzates were first used as carbon growth agents for CNTs in a reactor, a process that lowered their carbon content and increased their hydrogen content. Thereafter, the unreacted hydrocarbon pyrolyzates and the generated hydrogen were mixed with air and burned. This conversion of solid waste plastics to gaseous fuels allowed thorough mixing with air and, upon ignition, the formation of environmentally benign fuel-lean premixed flames for subsequent power generation purposes. The CNT generation in the reactor took place by chemical vapor deposition (CVD) on untreated stainless steel mesh substrates, which also served as catalysts. Provisions were made for automatic motion and replenishment of the substrate/catalyst for continuous CNT production. The reactor was specifically designed to have a cold-wall configuration, where only the catalyst substrate was heated to a temperature of 800°C, in an otherwise unheated chamber. This cold-wall reactor has significantly lower energy consumption than conventional hot-wall reactors of similar dimensions and throughput. This work is part of an overall study that aims at illustrating the upcycling of common recycled post-consumer plastics simultaneously to gaseous fuels and value-added nanomaterials. Its specific goal was to produce the latter in a newly designed low energy input reactor.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors acknowledge technical help in the design and construction of the cold gas CNT reactor by the Northeastern University undergraduate students Josh Beeman, Greg Duston, and Ryan St. Pierre. Technical support by Rasam Soehilian and Jonathan Doughty is also acknowledged.
References
Aguiar, M. R., Verissimo, C., Ramos, A. C. S., Moshkalev, S. A., and Swart, J. W. (2009). “Synthesis of carbon nanotubes and nanofibers by thermal CVD on and support layers.” J. Nanosci. Nanotechnol., 9(7), 4143–4150.
Alves, J. O., Zhuo, C., Levendis, Y. A., and Tenório, J. A. S. (2011a). “Catalytic conversion of wastes from the bioethanol production into carbon nanomaterials.” Appl. Catal., B, 106(3–4), 433–444.
Alves, J. O., Zhuo, C., Levendis, Y. A., and Tenório, J. A. S. (2011b). “Microstructural analysis of carbon nanomaterials produced from pyrolysis/combustion of styrene-butadiene-rubber (SBR).” Mater. Res., 14(4), 499–504.
Caponero, J., Tenorio, J. A. S., Levendis, Y. A., and Carlson, J. (2005). “Emissions of batch combustion of waste tire chips: The pyrolysis effect.” Combust. Sci. Technol., 177(2), 347–381.
Conesa, J. A., Font, R., Marcilla, A., and Garcia, A. N. (1994). “Pyrolysis of polyethylene in a fluidized bed reactor.” Energy Fuels, 8(6), 1238–1246.
De Volder, M. F. L., Tawfick, S. H., Baughman, R. H., and Hart, A. J. (2013). “Carbon nanotubes: Present and future commercial applications.” Science, 339(6119), 535–539.
Environmental Protection Agency (EPA). (2013). “U.S.A. municipal solid waste generation. Recycling, and disposal in the United States: Facts and figures for 2012.” Washington, DC, 〈http://www.epa.gov/osw/nonhaz/municipal/pubs/2012_msw_fs.pdf〉 (Aug. 4, 2014).
Ergut, A., Levendis, Y. A., Howard, J. B., Richter, H., and Carlson, J. B. (2007). “The effect of equivalence ratio on the soot onset chemistry in one-dimensional, atmospheric pressure, premixed ethylbenzene flames.” Combust. Flame, 151(1–2), 173–195.
Finnie, P., Li-Pook-Than, A., Lefebvre, J., and Austing, D. G. (2006). “Optimization of methane cold wall chemical vapor deposition for the production of single walled carbon nanotubes and devices.” Carbon, 44(15), 3199–3206.
Gonçalves, C. K., Tenório, J. A. S., Levendis, Y. A., and Carlson, J. B. (2007a). “Emissions from the premixed combustion of gasified polyethylene.” Energy Fuels, 22(1), 372–381.
Gonçalves, C. K., Tenório, J. A. S., Levendis, Y. A., and Carlson, J. B. (2007b). “Emissions from premixed combustion of polystyrene.” Energy Fuels, 22(1), 354–362.
Gong, J., et al. (2013a). “Catalytic conversion of linear low density polyethylene into carbon nanomaterials under the combined catalysis of and poly(vinyl chloride).” Chem. Eng. J, 215–216, 339–347.
Gong, J., et al. (2013b). “Effect of the added amount of organically-modified montmorillonite on the catalytic carbonization of polypropylene into cup-stacked carbon nanotubes.” Chem. Eng. J., 225, 798–808.
Gong, J., et al. (2014a). “Striking influence of chain structure of polyethylene on the formation of cup-stacked carbon nanotubes/carbon nanofibers under the combined catalysis of CuBr and NiO.” Appl. Catal., B, 147, 592–601.
Gong, J., et al. (2014b). “Catalytic carbonization of polypropylene into cup-stacked carbon nanotubes with high performances in adsorption of heavy metallic ions and organic dyes.” Chem. Eng. J., 248, 27–40.
Hall, B., Zhuo, C., Levendis, Y. A., and Richter, H. (2011). “Influence of the fuel structure on the flame synthesis of carbon nanomaterials.” Carbon, 49(11), 3412–3423.
Harris, A. T., See, C. H., Liu, J., Dunens, O., and MacKenzie, K. (2008). “Towards the large-scale synthesis of carbon nanotubes in fluidised beds.” J. Nanosci. Nanotechnol., 8(5), 2450–2457.
Jinno, D., Gupta, A. K., and Yoshikawa, K. (2004). “Thermal decomposition characteristics of critical components in solid wastes.” Environ. Eng. Sci., 21(1), 65–72.
Koos, A. A., Dillon, F., Nicholls, R. J., Bulusheva, L., and Grobert, N. (2012). “N-SWCNTs production by aerosol-assisted CVD method.” Chem. Phys. Lett., 538, 108–111.
Kumar, M., and Ando, Y. (2010). “Chemical vapor deposition of carbon nanotubes: A review on growth mechanism and mass production.” J. Nanosci. Nanotechnol., 10(6), 3739–3758.
Kunadian, I., Andrews, R., Menguc, M. P., and Qian, D. (2009). “Multiwalled carbon nanotube deposition profiles within a CVD reactor: An experimental study.” Chem. Eng. Sci., 64(7), 1503–1510.
Kwok, C. T. M., et al. (2010). “Temperature and time dependence study of single-walled carbon nanotube growth by catalytic chemical vapor deposition.” Carbon, 48(4), 1279–1288.
Liu, J., Yuan, L. X., Yang, X. S., Elbert, A., and Harris, A. T. (2011). “Synthesis of vertically aligned carbon nanotube arrays on polyhedral catalysts.” Chem. Commun., 47(22), 6434–6436.
Plastics. (2013). “Plastics—The facts 2013: An analysis of European latest plastics production, demand and waste data, Brussels.” 〈http://www.plasticseurope.org/documents/document/20131018104201-plastics_the_facts_2013.pdf〉 (Aug. 4, 2014).
Plastic Waste Management Institute. (2014). “Plastic products, plastic waste and resource recovery 2012.” Tokyo, Japan, 〈http://www.pwmi.or.jp/ei/siryo/ei/ei_pdf/ei43.pdf〉 (Aug. 4, 2014).
Sano, N., Yamamoto, S., and Tamon, H. (2012). “Uniform synthesis of multi-walled carbon nanotubes in a stainless steel porous block.” Carbon, 50(15), 5628–5630.
Sawaguchi, T., Inami, T., Kuroki, T., and Ikermura, T. (1980). “Studies on thermal degradation of synthetic polymers. 12. Kinetic approach to intensity function concerning pyrolysis condition for polyethylene low polymer.” Ind. Eng. Chem. Process Des. Dev., 19(1), 174–179.
Sawaguchi, T., Suzuki, K., Kuroki, T., and Ikemura, T. (1981). “Studies on thermal degradation of synthetic polymers. XV. Estimation of the product yield on the basis of intensity function for thermal gasification of isotactic and atactic polypropylenes.” J. Appl. Polym. Sci., 26(4), 1267–1274.
Shemwell, B. E., and Levendis, Y. A. (2000). “Particulates generated from combustion of polymers (plastics).” J. Air Waste Manage. Assoc., 50(1), 94–102.
Shi, S. X., et al. (2012). “High yield preparation of carbon nanotube arrays of good quality by CVD.” Chem. Vap. Deposition, 18(7–9), 201–208.
Soheilian, R., Davies, A., Talebi Anaraki, S., Zhuo, C., and Levendis, Y. A. (2013). “Pyrolytic gasification of post-consumer polyolefins to allow for ‘clean’ premixed combustion.” Energy Fuels, 27(8), 4859–4868.
SolidWorks [Computer software]. Waltham, MA, Dassault Systèmes SOLIDWORKS.
Valles, C., Perez-Mendoza, M., Maser, W. K., and Benito, A. M. (2007). “CVD production of double-wall and triple-wall carbon nanotubes.” Diamond Relat. Mater., 16(4–7), 1087–1090.
Villoria, R. G. d., Figueredo, S. L., Hart, A. J., Steiner, S. A., III, Slocum, A. H., and Wardle, B. L. (2009). “High-yield growth of vertically aligned carbon nanotubes on continuously moving substrate.” Nanotechnology, 20(40), 1–8.
Wang, J., Ferreiro, G., Richter, H., Howard, J. B., Levendis, Y. A., and Carlson, J. (2002a). “Comparative study on destruction of polycyclic aromatic hydrocarbons from combustion of waste polystyrene.” Proc. Combust. Inst., 29(2), 2477–2484.
Wang, J., Levendis, Y. A., Richter, H., Howard, J. B., and Carlson, J. (2001). “Polycyclic aromatic hydrocarbon and particulate emissions from two-stage combustion of polystyrene: The effect of the primary furnace temperature.” Environ. Sci. Technol., 35(17), 3541–3552.
Wang, J., Richter, H., Howard, J. B., Levendis, Y. A., and Carlson, J. (2002b). “Polynuclear aromatic hydrocarbon and particulate emissions from two-stage combustion of polystyrene: The effects of the secondary furnace (afterburner) temperature and soot filtration.” Environ. Sci. Technol., 36(4), 797–808.
Wang, Z., Richter, H., Howard, J. B., Jordan, J., Carlson, J., and Levendis, Y. A. (2003a). “Laboratory investigation of the products of the incomplete combustion of waste plastics and techniques for their minimization.” Ind. Eng. Chem. Res., 43(12), 2873–2886.
Wang, Z., Wang, J., Richter, H., Howard, J. B., Carlson, J., and Levendis, Y. A. (2003b). “Comparative study on polycyclic aromatic hydrocarbons, light hydrocarbons, carbon monoxide, and particulate emissions from the combustion of polyethylene, polystyrene, and poly(vinyl chloride).” Energy Fuels, 17(4), 999–1013.
Wen, X., et al. (2014). “Nanosized carbon black combined with Ni2O3 as “universal” catalysts for synergistically catalyzing carbonization of polyolefin wastes to synthesize carbon nanotubes and application for supercapacitors.” Environ. Sci. Technol., 48(7), 4048–4055.
Westerhout, R. W. J., Waanders, J., Kuipers, J. A. M., and van Swaaij, W. P. M. (1998). “Recycling of polyethene and polypropene in a novel bench-scale rotating cone reactor by high-temperature pyrolysis.” Ind. Eng. Chem. Res., 37(6), 2293–2300.
Wheatley, L., Levendis, Y. A., and Vouros, P. (1993). “Exploratory study on the combustion and PAH emissions of selected municipal waste plastics.” Environ. Sci. Technol., 27(13), 2885–2895.
Yi, W. W., and Yang, Q. Q. (2010). “CVD growth of secondary carbon nanotubes and its effect on field electron emission.” Diamond Relat. Mater., 19(7–9), 923–926.
Zhang, Q., Huang, J. Q., Zhao, M. Q., Qian, W. Z., Wang, Y., and Wei, F. (2008). “Radial growth of vertically aligned carbon nanotube arrays from ethylene on ceramic spheres.” Carbon, 46(8), 1152–1158.
Zhao, J., et al. (2012). “Structural improvement of CVD multi-walled carbon nanotubes by a rapid annealing process.” Diamond Relat. Mater., 25, 24–28.
Zhuo, C., Alves, J. O., Tenorio, J. A. S., and Levendis, Y. A. (2012). “Synthesis of carbon nanomaterials through up-cycling agricultural and municipal solid wastes.” Ind. Eng. Chem. Res., 51(7), 2922–2930.
Zhuo, C., Hall, B., Levendis, Y., and Richter, H. (2011). “A novel technology for green(er) manufacturing of CNTs via recycling of waste plastics.” MRS Online Proc. Lib., 1317, in press.
Zhuo, C., Hall, B., Richter, H., and Levendis, Y. (2010). “Synthesis of carbon nanotubes by sequential pyrolysis and combustion of polyethylene.” Carbon, 48(14), 4024–4034.
Zhuo, C., and Levendis, Y. A. (2013). “Upcycling waste plastics into carbon nanomaterials: A review.” J. Appl. Polym. Sci., 131(4), in press.
Zhuo, C., Wang, X., Nowak, W., and Levendis, Y. A. (2014). “Oxidative heat treatment of 316L stainless steel for effective catalytic growth of carbon nanotubes.” Appl. Surf. Sci., 313, 227–236.
Information & Authors
Information
Published In
Journal of Energy Engineering
Volume 141 • Issue 2 • June 2015
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Apr 28, 2014
Accepted: Jul 7, 2014
Published online: Sep 2, 2014
Discussion open until: Feb 2, 2015
Published in print: Jun 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.