Buckling Behavior of Corroded Four-Sided Simply Supported Plates with Longitudinal Stress Gradients
Publication: Journal of Engineering Mechanics
Volume 148, Issue 10
Abstract
This paper mainly investigated the buckling behavior of corroded four-sided simply supported plates with longitudinal stress gradients. The effect of corrosion surface topography on the buckling behavior of the four-sided simply supported plate was investigated by reverse reconstruction. The eigenvalue buckling analysis was also carried out to reveal the influence of corrosion depth, area, and location on the buckling load of simply supported plates. Based on the analysis, the theoretical formula of the buckling load of corroded four-sided simply supported plates with longitudinal stress gradients was established by the energy method. The results showed that the first order buckling mode of corroded plates was asymmetric and the highest peak was located in the weak section. The stress state led the corrosion parameters to have different effects on the buckling load of four-sided simply supported plates. The corrosion location had little effect on the buckling load of four-sided simply supported plates under uniform pressure. However, for the plate under nonuniform pressure, the closer the distance between the corrosion location and the compression zone of plate, the smaller the buckling load was. The perforation changed the force mechanism of the plate, and the noncorroded part surrounding the opening hole formed a new three-sided simply supported plate, leading to an increase in the buckling load. Finally, on the basis of the response surface method, the key parameters governing the local buckling were identified, leading to an easy-to-use formula to determine the buckling load.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This paper is supported by the National Natural Science Foundation of China (Grants No. 52108292), and China Postdoctoral Science Foundation (Grant No. 2021M703508). The supports are highly acknowledged. The authors also would like to express gratitude to the reviewers for their comments.
References
Albrecht, P., and T. T. Hall. 2003. “Atmospheric corrosion resistance of structural steels.” J. Mater. Civ. Eng. 15 (1): 2–24. https://doi.org/10.1061/(ASCE)0899-1561(2003)15:1(2).
Beaulieu, L. V., F. Legeron, and S. Langlois. 2010. “Compression strength of corroded steel angle members.” J. Constr. Steel Res. 66 (11): 1366–1373. https://doi.org/10.1016/j.jcsr.2010.05.006.
CEN (European Committee for Standardization). 2003. Eurocode 3: Design of steel structures, part 1-1: General rules and rules for buildings. Brussels: CEN.
Chen, J. 2014. Stability of steel structures theory and design. 6th ed. Beijing: China Science Press.
Dunbar, T. E., N. Pegg, F. Taheri, and L. Jiang. 2004. “A computational investigation of the effects of localized corrosion on plates and stiffened panels.” Mar. Struct. 17 (5): 385–402. https://doi.org/10.1016/j.marstruc.2004.08.012.
Goto, Y., and N. Kawanishi. 2004. “Analysis to predict long-term mechanical performance of steel structures with histories of corrosion and repair.” J. Struct. Eng. 130 (10): 1578–1585. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:10(1578).
Guo, X. Y., J. F. Kang, and J. S. Zhu. 2018. “3D cellular automata-based numerical simulation of atmospheric corrosion process on weathering steel.” J. Mater. Civ. Eng. 30 (11): 04018296. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002502.
Huang, Y., Y. Zhang, G. Liu, and Q. Zhang. 2010. “Ultimate strength assessment of hull structural plate with pitting corrosion damnification under biaxial compression.” Ocean Eng. 37 (17–18): 1503–1512. https://doi.org/10.1016/j.oceaneng.2010.08.001.
Jiang, X. L., and C. G. Soares. 2009. “Nonlinear FEM analysis of pitted mild steel square plate subjected to in-plane compression.” J. Ship Mech. 13 (3): 398–405.
Khedmati, M. R., M. M. Roshanali, and Z. Nouri. 2011. “Strength of steel plates with both-sides randomly distributed with corrosion wastage under uniaxial compression.” Thin Walled Struct. 49 (2): 325–342. https://doi.org/10.1016/j.tws.2010.10.002.
Lanzo, A. D., G. Garcea, and R. Casciaro. 1995. “Asymptotic post-buckling analysis of rectangular plates by HC finite elements.” Int. J. Numer. Methods Eng. 38 (14): 2325–2345. https://doi.org/10.1002/nme.1620381403.
Miura, S., M. Murase, T. Okamoto, D. D. Tung, and E. Iwasaki. 2017. “Corrosion behavior and applicability of weathering steel in Vietnam.” J. Mater. Civ. Eng. 29 (4): 04016264. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001817.
Moen, C. D., and B. W. Schafer. 2009. “Elastic buckling of thin plates with holes in compression or bending.” Thin Walled Struct. 47 (12): 1597–1607. https://doi.org/10.1016/j.tws.2009.05.001.
Nakai, T., H. Matsushita, and N. Yamamoto. 2006. “Effect of pitting corrosion on the ultimate strength of steel plates subjected to in-plane compression and bending.” J. Mar. Sci. Tech. 11 (1): 52–64. https://doi.org/10.1007/s00773-005-0203-4.
Nakai, T., H. Matsushita, N. Yamamoto, and H. Araib. 2004. “Effect of pitting corrosion on local strength of hold frames of bulk carriers (1st report).” Mar. struct. 17 (5): 403–432. https://doi.org/10.1016/j.marstruc.2004.10.001.
Ok, D., Y. Pu, and A. Incecik. 2007a. “Artificial neural networks and their application to assessment of ultimate strength of plates with pitting corrosion.” Ocean Eng. 34 (17–18): 2222–2230. https://doi.org/10.1016/j.oceaneng.2007.06.007.
Ok, D., Y. Pu, and A. Incecik. 2007b. “Computation of ultimate strength of locally corroded unstiffened plates under uniaxial compression.” Mar. Struct. 20 (1–2): 100–114. https://doi.org/10.1016/j.marstruc.2007.02.003.
Paik, J. K., J. M. Lee, and M. J. Ko. 2003. “Ultimate compressive strength of plate elements with pit corrosion wastage.” Proc. Inst. Mech. Eng., Part M: J. Eng. Marit. Environ. 217 (4): 185–200. https://doi.org/10.1177/147509020321700402.
Rahgozar, R. 2009. “Remaining capacity assessment of corrosion damaged beams using minimum curves.” J. Constr. Steel Res. 65 (2): 299–307. https://doi.org/10.1016/j.jcsr.2008.02.004.
Timoshenko, S. P., and J. M. Gere. 1961. Theory of elastic stability. 2nd ed., 493–525. New York: McGraw-Hill.
Zhang, Y., Y. Huang, and Y. Wei. 2017. “Ultimate strength experiment of hull structural plate with pitting corrosion damage under unaxial compression.” Ocean Eng. 130 (Jan): 103–114. https://doi.org/10.1016/j.oceaneng.2016.11.065.
Zhang, Y., Y. Huang, Q. Zhang, and G. Liu. 2016. “Ultimate strength of hull structural plate with pitting corrosion damnification under combined loading.” Ocean Eng. 116 (Apr): 273–285. https://doi.org/10.1016/j.oceaneng.2016.02.039.
Zhang, Z. X., S. H. Xu, and R. Li. 2020a. “Comparative investigation of the effect of corrosion on the mechanical properties of different parts of thin-walled steel.” Thin Walled Struct. 146 (Jan): 26–40. https://doi.org/10.1016/j.tws.2019.106450.
Zhang, Z. X., S. H. Xu, Y. D. Wang, B. Nie, and T. Wei. 2020b. “Local and post-buckling behavior of corroded axially-compressed steel columns” Thin Walled Struct. 157 (Dec): 107108. https://doi.org/10.1016/j.tws.2020.107108.
Ziemian, R. D. 2010. Guide to stability design criteria for metal structures. 6th ed. New York: Wiley.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Jan 31, 2022
Accepted: May 24, 2022
Published online: Jul 28, 2022
Published in print: Oct 1, 2022
Discussion open until: Dec 28, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.