Thermoelastic Modeling of Layered Composites Considering Bending and Shearing Effects
Publication: Journal of Engineering Mechanics
Volume 147, Issue 7
Abstract
Composite materials and structures often exhibit thermal stresses and deformations due to their thermal expansion mismatch. For a layered laminate, the stress transfer mechanism involves both bending and interfacial shearing, which have been evaluated by Stoney’s equation and shear lag models, respectively. However, the two theories cannot consider both effects simultaneously due to their distinct assumptions. Because bending and shearing effects coexist in the physical problem, higher accuracy and fidelity can be achieved by considering both mechanisms. This paper presents an analytical formulation to solve this boundary value problem by constructing two separate trial functions from Navier’s equation. The analytical solution was proposed with an assumption of a perfectly bonded interface, and the corresponding coefficients were determined with the principle of stationary potential energy. The proposed model was applied to thermomechanical analysis of thin-film photovoltaic cells on smart window blinds, and good agreement was achieved between the theoretical prediction and finite-element results. A parametric study was also conducted to guide the design of solar window blinds and general bilayered composites.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some data, models, or codes that support the findings of this study are available from the corresponding author upon reasonable request, including the finite-element model and results, as well as the numerical data for comparisons with other previous models.
Acknowledgments
This work is sponsored by the National Science Foundation IIP #1738802 and CMMI#1762891, whose support is gratefully acknowledged.
References
Anbusagar, N. R. R., K. Palanikumar, and P. K. Giridharan. 2015. “Study of sandwich effect on nanoclay modified polyester resin GFR face sheet laminates.” Compos. Struct. 125 (Jul): 336–342. https://doi.org/10.1016/j.compstruct.2015.02.016.
Bogy, D. B. 1968. “Edge-bonded dissimilar orthogonal elastic wedges under normal and shear loading.” J. Appl. Mech. 35 (3): 460–466. https://doi.org/10.1115/1.3601236.
Chen, F. L., X. He, P. A. Prieto-Muñoz, and H. M. Yin. 2015. “Opening-mode fractures of a brittle coating bonded to an elasto-plastic substrate.” Int. J. Plast. 67 (Apr): 171–191. https://doi.org/10.1016/j.ijplas.2014.10.007.
Corkovic, S., R. W. Whatmore, and Q. Zhang. 2008. “Development of residual stress in sol-gel derived films: An experimental study.” J. Appl. Phys. 103 (8): 084101. https://doi.org/10.1063/1.2890142.
Feng, X., Y. Huang, H. Jiang, D. Ngo, and A. J. Rosakis. 2006. “The effect of thin film/substrate radii on the Stoney formula for thin film/substrate subjected to nonuniform axisymmetric misfit strain and temperature.” J. Mech. Mater. Struct. 1 (6): 1041–1053. https://doi.org/10.2140/jomms.2006.1.1041.
Freund, L. B., J. A. Floro, and E. Chason. 1999. “Extensions of the Stoney formula for substrate curvature to configurations with thin substrates or large deformations.” Appl. Phys. Lett. 74 (14): 1987–1989. https://doi.org/10.1063/1.123722.
Guo, L., and S. P. DeWeerth. 2010. “High-density stretchable electronics: Toward an integrated multilayer composite.” Adv. Mater. 22 (36): 4030–4033. https://doi.org/10.1002/adma.201000515.
Haftbaradaran, H., S. K. Soni, B. W. Sheldon, X. Xiao, and H. Gao. 2012. “Modified Stoney equation for patterned thin film electrodes on substrates in the presence of interfacial sliding.” J. Appl. Mech. 79 (3): 031018. https://doi.org/10.1115/1.4005900.
Hou, S., C. Shu, S. Zhao, T. Liu, X. Han, and Q. Li. 2015. “Experimental and numerical studies on multi-layered corrugated sandwich panels under crushing loading.” Compos. Struct. 126 (Aug): 371–385. https://doi.org/10.1016/j.compstruct.2015.02.039.
Huang, S., and X. Zhang. 2006. “Extension of the Stoney formula for film–substrate systems with gradient stress for MEMS applications.” J. Micromech. Microeng. 16 (2): 382–389. https://doi.org/10.1088/0960-1317/16/2/024.
Kim, S.-E., H.-T. Thai, and J. Lee. 2009. “A two variable refined plate theory for laminated composite plates.” Compos. Struct. 89 (2): 197–205. https://doi.org/10.1016/j.compstruct.2008.07.017.
Lee, Y. Y., E. W. M. Lee, and C. F. Ng. 2005. “Sound absorption of a finite flexible micro-perforated panel backed by an air cavity.” J. Sound Vib. 287 (1): 227–243. https://doi.org/10.1016/j.jsv.2004.11.024.
Li, L.-A., R.-J. Li, S.-B. Wang, Z.-Y. Wang, T. Li, and C.-W. Li. 2018. “Stress analysis of film-on-substrate structure under tensile loads.” Mech. Mater. 120 (May): 1–14. https://doi.org/10.1016/j.mechmat.2018.02.003.
Lin, Q., F. Chen, and H. Yin. 2017. “Experimental and theoretical investigation of the thermo-mechanical deformation of a functionally graded panel.” Eng. Struct. 138 (May): 17–26. https://doi.org/10.1016/j.engstruct.2017.01.062.
Lin, Q., Y. Zhang, A. Van Mieghem, Y.-C. Chen, N. Yu, Y. Yang, and H. Yin. 2020. “Design and experiment of a sun-powered smart building envelope with automatic control.” Energy Build. 223 (Sep): 110173. https://doi.org/10.1016/j.enbuild.2020.110173.
MacDonald, W. A., M. K. Looney, D. MacKerron, R. Eveson, R. Adam, K. Hashimoto, and K. Rakos. 2007. “Latest advances in substrates for flexible electronics.” J. Soc. Inf. Disp. 15 (12): 1075–1083. https://doi.org/10.1889/1.2825093.
Nairn, J. A., and D. A. Mendels. 2001. “On the use of planar shear-lag methods for stress-transfer analysis of multilayered composites.” Mech. Mater. 33 (6): 335–362. https://doi.org/10.1016/S0167-6636(01)00056-4.
Prieto-Muñoz, P. A., H. M. Yin, and W. G. Buttlar. 2013. “Two-dimensional stress analysis of low-temperature cracking in asphalt overlay/substrate systems.” J. Mater. Civ. Eng. 25 (9): 1228–1238. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000716.
Razeghi, M. 2002. “Short-wavelength solar-blind detectors-status, prospects, and markets.” Proc. IEEE 90 (6): 1006–1014. https://doi.org/10.1109/JPROC.2002.1021565.
Roy, R., D. K. Agrawal, and H. A. McKinstry. 1989. “Very low thermal expansion coefficient materials.” Annu. Rev. Mater. Sci. 19 (1): 59–81. https://doi.org/10.1146/annurev.ms.19.080189.000423.
Stoney, G. G. 1909. “The tension of metallic films deposited by electrolysis.” Proc. R. Soc. London, Ser. A 82 (553): 172–175. https://doi.org/10.1098/rspa.1909.0021.
Suhir, E. 1988. “An approximate analysis of stresses in multilayered elastic thin films.” J. Appl. Mech. 55 (1): 143–148. https://doi.org/10.1115/1.3173620.
Sumitomo, T., H. Huang, L. Zhou, and J. Shimizu. 2011. “Nanogrinding of multi-layered thin film amorphous Si solar panels.” Int. J. Mach. Tools Manuf. 51 (10): 797–805. https://doi.org/10.1016/j.ijmachtools.2011.07.001.
Timm, D. H., B. B. Guzina, and V. R. Voller. 2003. “Prediction of thermal crack spacing.” Int. J. Solids Struct. 40 (1): 125–142. https://doi.org/10.1016/S0020-7683(02)00496-1.
Yang, D. J., Z. F. Yuan, P. H. Lee, and H. M. Yin. 2012. “Simulation and experimental validation of heat transfer in a novel hybrid solar panel.” Int. J. Heat Mass Transfer 55 (4): 1076–1082. https://doi.org/10.1016/j.ijheatmasstransfer.2011.10.003.
Yang, Q., B. Zheng, K. Zhang, and J. Zhu. 2013. “Analytical solution of a bilayer functionally graded cantilever beam with concentrated loads.” Arch. Appl. Mech. 83 (3): 455–466. https://doi.org/10.1007/s00419-012-0693-6.
Yim, W. M., and R. J. Paff. 1974. “Thermal expansion of AlN, sapphire, and silicon.” J. Appl. Phys. 45 (3): 1456–1457. https://doi.org/10.1063/1.1663432.
Yin, H. M., W. G. Buttlar, and G. H. Paulino. 2007. “Simplified solution for periodic thermal discontinuities in asphalt overlays bonded to rigid pavements.” J. Transp. Eng. 133 (1): 39–46. https://doi.org/10.1061/(ASCE)0733-947X(2007)133:1(39).
Yin, H. M., and P. A. Prieto-Muñoz. 2013. “Stress transfer through fully bonded interface of layered materials.” Mech. Mater. 62 (Aug): 69–79. https://doi.org/10.1016/j.mechmat.2013.03.007.
Yin, H. M., D. J. Yang, G. Kelly, and J. Garant. 2013. “Design and performance of a novel building integrated PV/thermal system for energy efficiency of buildings.” Sol. Energy 87 (Jan): 184–195. https://doi.org/10.1016/j.solener.2012.10.022.
Zhao, Z. B., J. Hershberger, S. M. Yalisove, and J. C. Bilello. 2002. “Determination of residual stress in thin films: A comparative study of X-ray topography versus laser curvature method.” Thin Solid Films 415 (1): 21–31. https://doi.org/10.1016/S0040-6090(02)00489-3.
Zulkifli, R., J. Mohd Nor, M. F. Mat Tahir, A. R. Ismail, and M. Nuawi. 2008. “Acoustic properties of multi-layer coir fibres sound absorption panel.” J. Appl. Sci. 8 (20): 3709–3714. https://doi.org/10.3923/jas.2008.3709.3714.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Jul 1, 2020
Accepted: Feb 17, 2021
Published online: Apr 26, 2021
Published in print: Jul 1, 2021
Discussion open until: Sep 26, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Chunlin Wu, Liangliang Zhang, Huiming Yin, Stress Concentration of a Microvoid Embedded in a Bilayered Material Considering the Boundary Effects, Journal of Engineering Mechanics, 10.1061/JENMDT.EMENG-6779, 149, 2, (2023).
- Huiming Yin, Mehdi Zadshir, Frank Pao, Fundamentals of BIPVT design and integration, Building Integrated Photovoltaic Thermal Systems, 10.1016/B978-0-12-821064-2.00003-1, (45-129), (2022).