Optimization of Frame Structures with Kinematical Indeterminacy for Optimum Folding
Publication: Journal of Engineering Mechanics
Volume 145, Issue 9
Abstract
The principle of folding analysis of frame structures with kinematical indeterminacy is widely used in the field of engineering. However, the design process of the efficient configuration for spatial structures in three-dimensional space is still a crucial problem. This paper presents a new methodology for finding the optimal folding strategy for frame structures, which is established on the basis of the generalized inverse theory and genetic algorithm (GA). Foldable structures are generated by inserting additional hinges into the appropriate locations of the spatial structures. Several numerical examples of spatial frame structures are analyzed using the proposed method. The results demonstrate that the proposed method is able to obtain the optimal foldable structures that have both high folding efficiency and a relatively simple folding mechanism. The characteristics of the obtained optimal results are discussed. The feasibility of this approach is demonstrated by the application of finding the optimal results of the spatial structures with several fundamental geometries.
Get full access to this article
View all available purchase options and get full access to this article.
References
Adriaenssens, S., P. Block, D. Veenendaal, and C. Williams. 2014. Shell structures for architecture form finding and optimization. London: Routledge.
Carpentieri, G., R. E. Skelton, and F. Fraternali. 2017. “A minimal mass deployable structure for solar energy harvesting on water canals.” Struct. Multidiscip. Optim. 55 (2): 449–458. https://doi.org/10.1007/s00158-016-1503-5.
Chahat, N., R. E. Hodges, J. Sauder, M. Thomson, and Y. Rahmat-Samii. 2017. “The deep-space network telecommunication CubeSat antenna: Using the deployable Ka-band mesh reflector antenna.” IEEE Antennas Propag. Mag. 59 (2): 31–38. https://doi.org/10.1109/MAP.2017.2655576.
Chen, Y., Z. You, and T. Tarnai. 2005. “Threefold-symmetric Bricard linkages for deployable structures.” Int. J. Solids Struct. 42 (8): 2287–2301. https://doi.org/10.1016/j.ijsolstr.2004.09.014.
Dai, L., F. Guan, and J. K. Guest. 2014. “Structural optimization and model fabrication of a double-ring deployable antenna truss.” Acta Astronaut. 94 (2): 843–851. https://doi.org/10.1016/j.actaastro.2013.10.002.
Ding, W., Q. Ruan, and Y.-A. Yao. 2016. “Design and locomotion analysis of a novel deformable mobile robot with two spatial reconfigurable platforms and three kinematic chains.” Proc. Inst. Mech. Eng. Part C: J. Mech. Eng. Sci. 231 (8): 1481–1499. https://doi.org/10.1177/0954406216641453.
Dinh, T. D., A. Rezaei, T. Linthout, M. Mollaert, D. Van Hemelrijck, and W. Van Paepegem. 2017. “A computational compensation method for fabric panels of tensioned membrane structures using a shape optimization method based on gradientless algorithms.” Int. J. Solids Struct. 112 (May): 16–24. https://doi.org/10.1016/j.ijsolstr.2017.02.026.
Goldberg, D. E., and J. H. Holland. 1988. “Genetic algorithms and machine learning.” Mach. Learn. 3 (2): 95–99. https://doi.org/10.1023/A:1022602019183.
Hangai, Y., and K. Kawaguchi. 1991. Shape analysis—Generalized inverses and applications. Tokyo: Baifukan Press.
Herath, M. T., S. Natarajan, B. G. Prusty, and N. S. John. 2015. “Isogeometric analysis and genetic algorithm for shape-adaptive composite marine propellers.” Comput. Methods Appl. Mech. Eng. 284 (Feb): 835–860. https://doi.org/10.1016/j.cma.2014.10.028.
Holland, J. H. 1975. Adaptation in natural and artificial systems. Ann Arbor, MI: University of Michigan Press.
Kading, B. M., J. Straub, and D. J. Whalen. 2014. “A novel deployable array architecture for micro to full sized satellites.” In Proc., AIAA SPACE 2014 Conf. and Exposition. Reston, VA: American Institute of Aeronautics and Astronautics.
Kawaguchi, K., Y. Hangai, and K. Miyazaki. 1993. “The dynamic analysis of kinematically indeterminate frameworks.” In Proc., IASS-MSU Symp., 569–576. Madrid, Spain: International Association for Shell and Spatial Structures.
Kawaguchi, K., K. Nabana, and Y. Hangai. 1996. “Considerations for folding analysis for frame structure.” In Mobile and Rapidly Assembled Structures II, Proc., 2nd Int. Conf. on Mobile and Rapidly Assembled Structures, 383–394. Southampton, UK: WIT Press.
Kawaguchi, M. 1991. “Design problems of long span spatial structures.” Eng. Struct. 13 (2): 144–163. https://doi.org/10.1016/0141-0296(91)90048-H.
Kawaguchi, M., and M. Abe. 2002. “On some characteristics of pantadome system.” In Proc., Lightweight Structures in Civil Engineering, 51–57. Madrid, Spain: International Association for Shell and Spatial Structures.
Lázaro, C., A. Domingo, M. Kawaguchi, A. Candenas, and F. Palacios. 2007. “Renovation of the bullring arena of Xàtiva (Spain).” In Proc., Structural Architecture: Proc., IASS Symp. Madrid, Spain: International Association for Shell and Spatial Structures.
Liu, X., M. Wu, X. Ma, and H. Fang. 2017. “Design and analysis of a cable network system for a deployable reflector.” J. Spacecraft Rockets 54 (5): 1005–1014. https://doi.org/10.2514/1.A33712.
Mallikarachchi, H. M. Y. C., and S. Pellegrino. 2014. “Design of ultrathin composite self-deployable booms.” J. Spacecraft Rockets 51 (6): 1811–1821. https://doi.org/10.2514/1.A32815.
Montemurro, M., H. Nasser, Y. Koutsawa, S. Belouettar, A. Vincenti, and P. Vannucci. 2012. “Identification of electromechanical properties of piezoelectric structures through evolutionary optimisation techniques.” Int. J. Solids Struct. 49 (13): 1884–1892. https://doi.org/10.1016/j.ijsolstr.2012.03.031.
Ohsaki, M., S. Tsuda, and Y. Miyazu. 2016. “Design of linkage mechanisms of partially rigid frames using limit analysis with quadratic yield functions.” Int. J. Solids Struct. 88–89 (Jun): 68–78. https://doi.org/10.1016/j.ijsolstr.2016.03.023.
Oliveira, L. L., A. A. Freitas, and R. Tinós. 2018. “Multi-objective genetic algorithms in the study of the genetic code’s adaptability.” Inf. Sci. 425 (Jan): 48–61. https://doi.org/10.1016/j.ins.2017.10.022.
Pellegrino, S. 2001. Deployable structures. New York: Springer.
Presbitero, A., V. Krzhizhanovskaya, E. Mancini, R. Brands, and P. Sloot. 2016. “Immune system model calibration by genetic algorithm.” Procedia Comput. Sci. 101: 161–171. https://doi.org/10.1016/j.procs.2016.11.020.
Santoni, F., F. Piergentili, S. Donati, M. Perelli, A. Negri, and M. Marino. 2014. “An innovative deployable solar panel system for Cubesats.” Acta Astronaut. 95 (Feb–Mar): 210–217. https://doi.org/10.1016/j.actaastro.2013.11.011.
Soykasap, Ö. 2009. “Deployment analysis of a self-deployable composite boom.” Compos. Struct. 89 (3): 374–381. https://doi.org/10.1016/j.compstruct.2008.08.012.
Tibert, A. G., and S. Pellegrino. 2002. “Deployable tensegrity reflectors for small satellites.” J. Spacecraft Rockets 39 (5): 701–709. https://doi.org/10.2514/2.3867.
Wierzbicki, T., and W. Abramowicz. 1983. “On the crushing mechanics of thin-walled structures.” J. Appl. Mech. 50 (4a): 727–734. https://doi.org/10.1115/1.3167137.
Xiang, P., and A. Nishitani. 2015. “Optimum design of tuned mass damper floor system integrated into bending-shear type building based on , , and stability maximization criteria.” Struct. Control and Health Monit. 22 (6): 919–938. https://doi.org/10.1002/stc.1725.
You, Z., and N. Cole. 2006. “Self-locking bi-stable deployable booms.” In Proc., 47th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conf. Reston, VA: American Institute of Aeronautics and Astronautics.
Zhang, P., and J. Feng. 2017. “Initial prestress design and optimization of tensegrity systems based on symmetry and stiffness.” Int. J. Solids Struct. 106–107 (Feb): 68–90. https://doi.org/10.1016/j.ijsolstr.2016.11.030.
Zhang, T., M. Wu, and F. Guan. 2016. “Deployment study on a single-layer deployable truss structure driven by elastic components.” J. Int. Assoc. Shell Spatial Struct. 57 (4): 285–294. https://doi.org/10.20898/j.iass.2016.190.855.
Zlatanov, S., D. Lu, X. Ding, M. Zoppi, and S. D. Guest. 2015. “A network of type III Bricard linkages.” In Proc., ASME 2015 Int. Design Engineering Technical Conf. and Computers and Information in Engineering Conf. New York: ASME.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Apr 17, 2018
Accepted: Feb 11, 2019
Published online: Jul 11, 2019
Published in print: Sep 1, 2019
Discussion open until: Dec 11, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.