Elastoplastic Dilatant Interface Model for Cyclic Bond-Slip Behavior of Reinforcing Bars
Publication: Journal of Engineering Mechanics
Volume 142, Issue 2
Abstract
This paper presents a new interface model to simulate the cyclic bond-slip behavior of steel reinforcing bars embedded in concrete. A multi-surface plasticity formulation is used to model two major inelastic deformation mechanisms occurring in bond slip. One is the crushing and shearing of the concrete between the bar ribs, and the other is the sliding between the concrete and bar surfaces. These two mechanisms are represented by different yield surfaces and nonassociated flow rules. The flow rules account for the shear dilatation of the interface induced by the wedging action of the bar ribs and crushed concrete particles. The interface model has been implemented in a finite element analysis program and has been validated with experimental data. The model is easy to calibrate and is able to reproduce the bond-slip behavior of bars under a wide range of confinement situations, including bar pullout and concrete splitting failures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors wish to thank Fundacio La Caixa and Fundacion Caja Madrid for providing graduate fellowships to the first author for his doctoral studies at the University of California at San Diego, during which the research presented in this paper was conducted. However, opinions expressed in this paper are those of the authors and do not necessarily reflect those of the sponsors.
References
ABAQUS version 6.10 [Computer software]. Providence, RI, Dassault Systèmes.
ACI (American Concrete Institute). (2003). “Bond and development of straight reinforcing bars in tension.”, Farmington Hills, MI.
ACI (American Concrete Institute). (2011). “Building code requirements for structural concrete (ACI 318-11) and commentary.” Farmington Hills, MI.
Caballero, A., Willam, K. J., and Carol, I. (2008). “Consistent tangent formulation for 3D interface modeling of cracking/fracture in quasi-brittle materials.” Comput. Methods Appl. Mech. Eng., 197(33–40), 2804–2822.
Carol, I., Prat, P. C., and Lopez, C. M. (1997). “Normal/shear cracking model: application to discrete crack analysis.” J. Eng. Mech., 765–773.
Cox, J. V., and Herrmann, L. R. (1998). “Development of a plasticity bond model for steel reinforcement.” Mech. Cohesive-Frict. Mater., 3(2), 155–180.
Cox, J. V., and Herrmann, L. R. (1999). “Validation of a plasticity bond model for steel reinforcement.” Mech. Cohesive-Frict. Mater., 4(4), 361–389.
FIB (Fédération Internationale du Béton). (2000). “fib bulletin 10: Bond of reinforcement in concrete.”, Lausanne, Switzerland.
Herrmann, L. R., and Cox, J. V. (1994). “Development of a plasticity bond model for reinforced concrete.”, Naval Facilities Engineering Service Center, Port Hueneme, CA.
Koutromanos, I., and Shing, P. B. (2012). “Cohesive crack model to simulate cyclic response of concrete and masonry structures.” ACI Struct. J., 109(3), 349–358.
Lee, J., and Fenves, G. L. (1998). “Plastic-damage model for cyclic loading of concrete structures.” J. Eng. Mech., 892–900.
Lotfi, H. R., and Shing, P. B. (1994). “Interface model applied to fracture of masonry structures.” J. Struct. Eng., 63–80.
Lubliner, J., Oliver, J., Oller, S., and Oñate, E. (1989). “A plastic-damage model for concrete.” Int. J. Solids Struct., 25(3), 299–326.
Lundgren, K. (2000). “Pull-out tests of steel-encased specimens subjected to reversed cyclic loading.” Mater. Struct., 33(7), 450–456.
Lundgren, K., and Gylltoft, K. (2000). “A model for the bond between concrete and reinforcement.” Mag. Concr. Res., 52(1), 53–63.
Lundgren, K., and Magnusson, J. (2001). “Three-dimensional modeling of anchorage zones in reinforced concrete.” J. Eng. Mech., 693–699.
Malvar, J. (1992). “Bond of reinforcement under controlled confinement.” ACI Mater. J., 89(6), 593–601.
Metelli, G., and Plizzari, G. A. (2014). “Influence of the relative rib area on bond behavior.” Mag. Concr. Res., 66(6), 277–294.
Murcia-Delso, J. (2013). “Bond-slip behavior and development of bridge column longitudinal reinforcing bars in enlarged pile shafts.” Ph.D. dissertation, Dept. of Structural Engineering, Univ. of California, San Diego, CA.
Murcia-Delso, J., Stavridis, A., and Shing, P. B. (2013). “Bond strength and cyclic bond deterioration of large-diameter bars.” ACI Struct. J., 110(4), 659–669.
Ortiz, M., and Popov, E. P. (1985). “Accuracy and stability of integration algorithms for elastoplastic constitutive relations.” Int. J. Numer. Methods Eng., 21(9), 1561–1576.
Puntel, E., Bolzon, G., and Saouma, V. E. (2006). “Fracture mechanics based model for joints under cyclic loading.” J. Eng. Mech., 1151–1159.
Serpieri, R., and Alfano, G. (2011). “Bond-slip analysis via a thermodynamically consistent interface model combining interlocking, damage and friction.” Int. J. Numer. Methods Eng., 85(2), 164–186.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Aug 4, 2014
Accepted: Jul 16, 2015
Published online: Sep 2, 2015
Published in print: Feb 1, 2016
Discussion open until: Feb 2, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.