Buckling Analysis of Eccentrically Stiffened Functionally Graded Toroidal Shell Segments under Mechanical Load
Publication: Journal of Engineering Mechanics
Volume 142, Issue 1
Abstract
An analytical approach is presented to investigate the linear buckling of eccentrically stiffened functionally graded thin toroidal shell segments subjected to axial compression, lateral pressure, and hydrostatic pressure. On the basis of classical thin shell theory, the smeared stiffener technique and the adjacent equilibrium criterion, the governing equations of buckling of eccentrically stiffened functionally graded toroidal shell segments are derived. The functionally graded toroidal shell segments with simply supported edges are reinforced by a ring and stringer stiffener system on an external surface. The resulting equations in the case of compressive and pressure loads are solved directly. The obtained results show the effects of stiffeners and input factors on the buckling behavior of these structures. In this paper, the results are also compared with the solutions published in the literature for the specific cases of a toroidal shell.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded by the Vietnam National Foundation for Science and Technology Development (NAFOSTED) under Grant 107.02-2013.25.
References
Bich, D. H, Phuong, N. T., and Tung, H. V. (2012). “Buckling of functionally graded conical panels under mechanical loads.” Compos. Struct., 94(4), 1379–1384.
Bich, D. H., Dung, D. V., Nam, V. H., and Phuong, N. T. (2013). “Nonlinear static and dynamic buckling analysis of imperfect eccentrically stiffened functionally graded circular cylindrical thin shells under axial compression.” Int. J. Mech. Sci., 74, 190–200.
Brush, D. O., and Almroth, B. O. (1975). Buckling of bars, plates and shells, McGraw-Hill, New York.
Dung, D. V., and Hoa, L. K. (2013). “Research on nonlinear torsional buckling and post-buckling of eccentrically stiffened functionally graded thin circular cylindrical shells.” Compos. Part B, 51, 300–309.
Huang, H., and Han, Q. (2008). “Buckling of imperfect functionally graded cylindrical shells under axial compression.” Eur. J. Mech. A/Solids, 27(6), 1026–1036.
Huang, H., and Han, Q. (2010). “Nonlinear dyamic buckling of functionally graded cylindrical shells subjected to time-dependent axial load.” Compos. Struct., 92(2), 593–598.
Hutchinson, J. W. (1967). “Initial post-buckling behavior of toroidal shell segments.” J. Solid Struct., 3(1), 97–115.
Karman, T. V., and Tsien, H. S. (1941). “The buckling of thin cylindrical shells under axial compression.” J. Aeronaut. Sci., 8(8), 303–312.
Li, S. R., and Batra, R. C. (2006). “Buckling of axially compressed thin cylindrical shells with functioncally graded middle layer.” Thin-Walled Struct., 44(10), 1039–1047.
McElman, J. A. (1967). Eccentrically stiffened shallow shells of double curvature, NASA, Washington, DC.
Phuong, N. T., and Bich, D. H. (2013). “Buckling analysis of eccentrically stiffened functionally graded circular cylindrical thin shells under mechanical load.” J. Math. Phys., 29(2), 55–72.
Shen, H. S. (2002). “Postbuckling analysis of axially-loaded functionally graded cylindrical shells in thermal enviroments.” Compos. Sci. Technol., 62(7–8), 977–987.
Shen, H. S. (2013). “Thermal postbuckling of shear deformable FGM cylindrical shells surrounded by an elastic medium.” J. Eng. Mech., 979–991.
Shen, H. S., and Leung, A. (2003). “Postbuckling of pressure-loaded functionally graded cylindrical panels in thermal environments.” J. Eng. Mech., 414–425.
Shen, H. S., and Noda, N. (2007). “Postbuckling of pressure-loaded FGM hybrid cylindrical shells in thermal environments.” Compos. Struct., 77(4), 546–560.
Sofiyev, A. H. (2010). “Buckling analysis of FGM circular shells under combined loads and resting on the Pasternak type elastic foundation.” Mech. Res. Commun., 37(6), 539–544.
Stein, M. (1964). “The influence of prebuckling deformations and stresses on the buckling of perfect cylinders.”, NASA, Washington, DC.
Stein, M., and McElman, J. A. (1965). “Buckling of segments of toroidal shells.” Am. Inst. Aeronaut. Astronaut. J., 3(9), 1704–1709.
Weaver, P. M. (2000). “Design of laminated composite cylindrical shells under axial compression.” Compos. Part B, 31(8), 669–679.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Dec 23, 2014
Accepted: Apr 6, 2015
Published online: May 26, 2015
Discussion open until: Oct 26, 2015
Published in print: Jan 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.