Single-Degree-of-Freedom Approach to Incorporate Axial Load Effects on Pressure Impulse Curves for Steel Columns
Publication: Journal of Engineering Mechanics
Volume 141, Issue 1
Abstract
In this paper, the moment-curvature behavior of a steel column under constant axial loading is implemented into a computationally efficient one-dimensional finite-element approach, utilizing Timoshenko beam theory, to determine the dynamic response of steel columns subjected to blasts. Then, a new single-degree-of-freedom (SDOF) approach is provided for determining pressure impulse curves for steel columns under constant axial loading. This SDOF approach relies on the newly defined concept of the reduced resistance-deflection function to accurately simulate the effects and the global instability failure mechanism, which are both caused by the axial load. The aforementioned finite-element approach is then used to thoroughly validate the newly proposed SDOF approach for deriving pressure impulse curves. It is shown that, despite the inherent simplicity of the approach, the newly proposed SDOF approach provides accurate and reliable results.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Joint support for the research presented in this paper was provided by the ARC Discovery Grant DP140103025 and the National Science Foundation of China under Grants 51278326 and 51238007 and is gratefully acknowledged.
References
ASCE. (1997). Design of blast resistant buildings in petrochemical facilities, Reston, VA.
ASCE. (2008). “Blast protection of buildings.” ASCE/SEI 59-11, Reston, VA.
Bathe, K. J. (1996). Finite element procedures, Prentice Hall, Englewood Cliffs, NJ.
Biggs, J. M. (1964). Introduction to structural dynamics, McGraw Hill, New York.
Dragos, J., and Wu, C. (2013). “A new general approach to derive normalised pressure impulse curves.” Int. J. Impact Eng., 62(Dec), 1–12.
Dragos, J., and Wu, C. (2014). “Application of normalized pressure impulse diagrams for vented and unvented confined blasts.” J. Eng. Mech., 593–603.
Dragos, J., Wu, C., Haskett, M., and Oehlers, D. (2013). “Derivation of normalized pressure impulse curves for flexural ultra high performance concrete slabs.” J. Struct. Eng., 875–885.
Fallah, A. S., and Louca, L. A. (2007). “Pressure-impulse diagrams for elastic-plastic-hardening and softening single-degree-of-freedom models subjected to blast loading.” Int. J. Impact Eng., 34(4), 823–842.
Jama, H. H., Bambach, M. R., Nurick, G. N., Grzebieta, R. H., and Zhao, X.-L. (2009). “Numerical modelling of square tubular steel beams subjected to transverse blast loads.” Thin-Walled Struct., 47(12), 1523–1534.
Jones, J., Wu, C., Oehlers, D. J., Whittaker, A. S., Marks, S., and Coppola, R. (2009). “Finite difference analysis of simply supported RC panels for blast effects.” Eng. Struct., 31(12), 2825–2832.
Krauthammer, T., Assadi-Lamouki, A., and Shanaa, H. M. (1993). “Analysis of impulsively loaded reinforced concrete structural elements—I. Theory.” Comput. Struct., 48(5), 851–860.
Krauthammer, T., Astarlioglu, S., Blasko, J., Soh, T. B., and Ng, P. H. (2008). “Pressure–impulse diagrams for the behavior assessment of structural components.” Int. J. Impact Eng., 35(8), 771–783.
Li, Q. M., and Meng, H. (2002a). “Pressure-impulse diagram for blast loads based on dimensional analysis and single-degree-of-freedom model.” J. Eng. Mech., 87–92.
Li, Q. M., and Meng, H. (2002b). “Pulse loading shape effects on pressure–impulse diagram of an elastic–plastic, single-degree-of-freedom structural model.” Int. J. Mech. Sci., 44(9), 1985–1998.
LS-DYNA 970 [Computer software]. Livermore, CA, Livermore Software Technology.
Mutalib, A. A., and Hao, H. (2011). “Development of P-I diagrams for FRP strengthened RC columns.” Int. J. Impact Eng., 38(5), 290–304.
Nassr, A. A., Razaqpur, A. G., Tait, M. J., Campidelli, M., and Foo, S. (2010). “Measured versus predicted response of steel beams under blast load.” Proc., 1st Int. Conf. of Protective Structures, Armour & Protection Science & Technology Centre, Defence Science and Technology Laboratory (DSTL), Ministry of Defence, Wiltshire, U.K.
Nassr, A. A., Razaqpur, A. G., Tait, M. J., Campidelli, M., and Foo, S. (2012). “Experimental performance of steel beams under blast loading.” J. Perform. Constr. Facil., 600–619.
Nassr, A. A., Razaqpur, A. G., Tait, M. J., Campidelli, M., and Foo, S. (2013). “Strength and stability of steel beam columns under blast load.” Int. J. Impact Eng., 55(May), 34–48.
Shi, Y., Hao, H., and Li, Z.-X. (2008). “Numerical derivation of pressure–impulse diagrams for prediction of RC column damage to blast loads.” Int. J. Impact Eng., 35(11), 1213–1227.
Shi, Y., Li, Z.-X., and Hao, H. (2010). “A new method for progressive collapse analysis of RC frames under blast loading.” Eng. Struct., 32(6), 1691–1703.
Timoshenko, S. P., and Gere, J. M. (1961). Theory of elastic stability, McGraw Hill, New York.
Urgessa, G. S., and Maji, A. K. (2010). “Dynamic response of retrofitted masonry walls for blast loading.” J. Eng. Mech., 858–864.
U.S. Department of Defense (DOD). (2008). “Structures to resist the effects of accidental explosions.” UFC 3-340-02, Washington, DC.
Wang, W., Zhang, D., and Lu, F. (2012). “The influence of load pulse shape on pressure-impulse diagrams of one-way RC slabs.” Struct. Eng. Mech., 42(3), 363–381.
Weaver, W., and Timoshenko, S. P. (1990). Vibration problems in engineering, 5th Ed., Wiley, New York.
Ye, Z. Q., and Ma, G. W. (2007). “Effects of foam claddings for structure protection against blast loads.” J. Eng. Mech., 41–47.
Zhou, X. Q., Kuznetsov, V. A., Hao, H., and Waschl, J. (2008). “Numerical prediction of concrete slab response to blast loading.” Int. J. Impact Eng., 35(10), 1186–1200.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Dec 2, 2013
Accepted: May 5, 2014
Published online: May 27, 2014
Published in print: Jan 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.