Plane-Strain Crack Problem in Transversely Isotropic Solids for Hydraulic Fracturing Applications
Publication: Journal of Engineering Mechanics
Volume 140, Issue 12
Abstract
This paper aims at understanding and predicting how pressurized cracks propagate in anisotropic brittle solids, a situation frequently encountered in hydraulic fracturing. Special attention is paid to transverse isotropy, often used to model shale. Although the theory of linear elastic fracture mechanics of anisotropic solids is well established at present, this paper shows that the application of Muskhelishvili’s formalism to Lekhnitskii’s anisotropic complex potentials provides a powerful tool to extend the validity of the classical tools of isotropic fluid-driven crack models to the anisotropic case, provided that the appropriate elastic constants are used. These elastic constants are identified and derived in closed form for transversely isotropic solids. The constants are shown to be directly related to quantities easily measured in a laboratory at macroscopic scale through indentation tests and acoustic measurements. Moreover, several crack-kinking criteria are compared. Contrary to the isotropic case, the crack-kinking criteria are not consistent among themselves, even in the case of a pure pressure loading. The orientation at which it is easier to propagate an already existing crack is sought. A critical crack length, below which this crack orientation is the one of minimal stiffness felt by the crack, is identified.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was funded by the X-Shale Hub: The Science and Engineering of Gas Shale, a collaboration among Shell, Schlumberger, and the Massachusetts Institute of Technology. The authors are grateful to Brice Lecampion from Schlumberger for his helpful advice.
References
Ayari, M., and Ye, Z. (1995). “Maximum strain theory for mixed mode crack propagation in anisotropic solids.” Eng. Fract. Mech., 52(3), 389–400.
Azhdari, A. (1996). “Energy-release rate and crack kinking in anisotropic brittle solids.” J. Mech. Phys. Solids, 44(6), 929–951.
Azhdari, A., and Nemat-Nasser, S. (1996). “Hoop stress intensity factor and crackkinking in anisotropic brittle solids.” Int. J. Solids Struct., 33(14), 2023–2037.
Azhdari, A., Nemat-Nasser, S., and Rome, J. (1998). “Experimental observations and computational modeling of fracturing in an anisotropic brittle crystal (sapphire).” Int. J. Fract., 94(3), 251–266.
Azhdari, A., Obata, M., and Nemat-Nasser, S. (2000). “Alternative solution methods for crack problems in plane anisotropic elasticity, with examples).” Int. J. Solids Struct., 37(44), 6433–6478.
Barnett, D., and Asaro, R. (1972). “The fracture mechanics of slit-like cracks in anisotropic elastic media.” J. Mech. Phys. Solids, 20(6), 353–366.
Brady, B., Elbel, J., Mack, M., Morales, H., Nolte, K., and Poe, B. (1992). “Cracking rock: Progress in fracture treatment design.” Oilfield Rev., 4(4), 4–17.
Bunger, A. P., Detournay, E., and Garagash, D. I. (2005). “Toughness-dominated hydraulic fracture with leak-off.” Int. J. Fract., 134(2), 175–190.
Carloni, C., Piva, A., and Viola, E. (2004). “Biaxial load effect on crack initiation for orthotropic materials.” Meccanica, 39(4), 331–344.
Cotterell, B., and Rice, J. (1980). “Slightly curved or kinked cracks.” Int. J. Fract., 16(2), 155–169.
Delafargue, A., and Ulm, F.-J. (2004). “Explicit approximations of the indentation modulus of elastically orthotropic solids for conical indenters.” Int. J. Solids Struct., 41(26), 7351–7360.
Desroches, J., et al. (1994). “The crack tip region in hydraulic fracturing.” Proc. R. Soc. Lond. A, 447(1929), 39–48.
Detournay, E. (2004). “Propagation regimes of fluid-driven fractures in impermeable rocks.” Int. J. Geomech., 35–45.
England, A., and Green, A. (1963). “Some two-dimensional punch and crack problems in classical elasticity.” Proc. Cambridge Philos. Soc., 59(2), 489–500.
Faal, R., and Fariborz, S. (2007). “Stress analysis of orthotropic planes weakened by cracks.” Appl. Math. Modell., 31(6), 1133–1148.
Garagash, D. I. (2006). “Plane-strain propagation of a fluid-driven fracture during injection and shut-in: Asymptotics of large toughness.” Eng. Fract. Mech., 73(4), 456–481.
Garagash, D. I., and Detournay, E. (2005). “Plane-strain propagation of a fluid-driven fracture: Small toughness solution.” J. Appl. Mech., 72(6), 916–928.
Geertsma, J., and de Klerk, F. (1969). “A rapid method of predicting width and extent of hydraulically induced fractures.” J. Pet. Technol., 21(12), 1571–1581.
Griffith, A. (1921). “The phenomena of rupture and flow in solids.” Philos. Trans. R. Soc. Lond. A, 221(582–593), 163–198.
Guyon, É., Hulin, J., and Petit, L. (2001). Hydrodynamique physique, EDP Sciences, Les Ulis, France (in French).
Hoenig, A. (1982). “Near-tip behavior of a crack in a plane anisotropic elastic body.” Eng. Fract. Mech., 16(3), 393–403.
Hu, J., and Garagash, D. I. (2010). “Plane-strain propagation of a fluid-driven crack in a permeable rock with fracture toughness.” J. Eng. Mech., 1152–1166.
Irwin, G. (1958). “Fracture.” Handbuche der physik, S. Flügge, ed., Vol. VI, Springer, Berlin, 551–590.
Laubie, H. (2013). “Linear elastic fracture mechanics in anisotropic solids: Application to fluid-driven crack propagation.” Master’s thesis, Massachusetts Institute of Technology, Cambridge, MA.
Leblond, J.-B. (2003). Mécanique de la rupture fragile et ductile, Lavoisier, Paris (in French).
Lekhnitskii, S. (1981). Theory of elasticity of an anisotropic elastic body, Mir Publishers, Moscow.
Muskhelishvili, N. (1953). Some basic problems of the mathematical theory of elasticity, Noordhoff, Groningen, Netherlands.
Nobile, L., Piva, A., and Viola, E. (2004). “On the inclined crack problem in an orthotropic medium under biaxial loading.” Eng. Fract. Mech., 71(4–6), 529–546.
Obata, M., and Nemat-Nasser, S. (1989). “Branched cracks in anisotropic elastic solids.” J. Appl. Mech., 56(4), 858–864.
Ortega, A., Ulm, F.-J., and Abousleiman, Y. (2009). “The nanogranular acoustic signature of shale.” Geophysics, 74(3), D65–D84.
Sih, G., Paris, P., and Irwin, G. R. (1965). “On cracks in rectilinearly anisotropic bodies.” Int. J. Fract., 1(3), 189–203.
Sneddon, I. (1946). “The distribution of stress in the neighbourhood of a crack in an elastic solid.” Proc. R. Soc. Lond. A, 187(1009), 229–260.
Sneddon, I., and Lowengrub, M. (1969). Crack problems in the classical theory of elasticity, Wiley, New York.
Spence, D., and Turcotte, D. (1985). “Magma-driven propagation of cracks.” J. Geophys. Res., 90(B1), 575–580.
Thomsen, L. (1986). “Weak elastic anisotropy.” Geophysics, 51(10), 1954–1966.
U.S. Energy Information Administration. (2012). “Annual energy outlook 2012.” Rep. No. DOE/EIA-0383(2012), U.S. Dept. of Energy, Washington, DC.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jul 23, 2013
Accepted: Apr 4, 2014
Published online: May 9, 2014
Discussion open until: Oct 9, 2014
Published in print: Dec 1, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.