Creep Consideration Effect on Meso-Scale Modeling of Concrete Hydration Process and Consequences on the Mechanical Behavior
Publication: Journal of Engineering Mechanics
Volume 139, Issue 12
Abstract
At an early age, hydration of cement leads to a reduction in volume (caused by Le Chatelier contraction) that induces autogenous shrinkage. In addition, hydration is an exothermic reaction, and an increase in temperature occurs (followed by a decrease). Because autogenous shrinkage arises only in cement paste, and because the coefficient of thermal expansion may be different between cement paste and aggregates, strain incompatibilities lead to an internal self-equilibrated state of stress. Depending especially on the concrete mix, initial cracking may occur at the cement-paste scale leading to a modification of the global concrete behavior. In this paper, finite-element simulations using a mesoscopic mesh are performed to access to the internal stresses and damage state resulting from the hydration process. Calculations take into account the autogenous shrinkage of the cement paste and the differential thermal behavior between cement paste and aggregates. The influences of basic creep strains, thermal boundary conditions, and concrete mix (by a simplified approach) are studied, and it is shown that for ordinary concrete, hydration leads to a slight reduction in elastic stiffness and tensile strength when creep is taken into account. However, for high-performance concrete, a significant reduction in the elastic stiffness and tensile strength is expected (with respect to the potential tensile strength) even if creep is taken into account.
Get full access to this article
View all available purchase options and get full access to this article.
References
Bažant, Z. P., and Kaplan, M. F. (1996). Concrete at high temperatures: Material properties and mathematical models, Pearson Education, Boston.
Bažant, Z. P., and Prasannan, S. (1989). “Solidification theory for concrete creep. I: Formulation.” J. Eng. Mech., 115(8), 1691–1703.
Benboudjema, F., and Torrenti, J.-M. (2008). “Early-age behavior of concrete nuclear containments.” Nucl. Eng. Des., 238(10), 2495–2506.
Bentz, D. (1997). “Three-dimensional computer simulation of portland cement hydration and microstructure development.” J. Am. Ceram. Soc., 80(1), 3–21.
Bisschop, J., and Van Mier, J. G. M. (2002). “Effect of aggregates on drying shrinkage microcracking in cement-based composites.” Mater. Struct., 35(8), 453–461.
Briffaut, M., Benboudjema, F., Torrenti, J.-M., and Nahas, G. (2011). “Numerical analysis of the thermal active restrained shrinkage ring test to study the early age behavior of massive concrete structures.” Eng. Struct., 33(4), 1390–1401.
Briffaut, M., Benboudjema, F., Torrenti, J.-M. and Nahas, G. (2012a). “Concrete early age basic creep: Experiments and tests of rheological modelling approaches.” Constr. Build. Mater., Vol. 36, 373–380.
Briffaut, M., Benboudjema, F., Torrenti, J.-M., and Nahas, G. (2012b). “Effects of early-age thermal behavior on damage risks in massive concrete structures.” Eur. J. Environ. Civil Eng., 16(5), 589–605.
Cervera, M., and Chiumenti, M. (2006). “Mesh objective tensile cracking via a local continuum damage model and a crack tracking technique.” Comput. Methods Appl. Mech. Eng., 196(1–3), 304–320.
de Larrard, T., Benboudjema, F., Colliat, J.-B., Torrenti, J.-M., and Deleruyelle, F. (2010). “Uncertainty propagation on damage evolution of a concrete structure submitted to coupled leaching and creep.” Eur. J. Environ. Civil Eng., 14(6–7), 891–921.
De Sa, C., Benboudjema, F., and Sicard, J. (2013). “Separation of damage mechanisms in concrete at high temperature.” Proc., 3rd Int. Symp. GeoProc'2008: Thermo-Hydromechanical and Chemical Coupling in Geomaterials and Applications, J.-F. Shao and N. Burlion, eds., John Wiley & Sons, Hoboken, NJ.
De Sa, C., Benboudjema, F., Thiery, M., and Sicard, J. (2008). “Analysis of microcracking induced by differential drying shrinkage.” Cement Concr. Compos., 30(10), 947–956.
De Schutter, G. (1999). “Degree of hydration based Kelvin model for the basic creep of early age concrete.” Mater. Struct., 32(4), 260–265.
De Schutter, G., and Taerwe, L. (1996). “Degree of hydration-based description of mechanical properties of early age concrete.” Mater. Struct., 29(6), 335–344.
De Schutter, G., and Taerwe, L. (1997). “Fracture energy of concrete at early ages.” Mater. Struct., 30(2), 67–71.
Fichant, S., La Borderie, C., and Pijaudiet-Cabot, G. (1999). “Isotropic and anisotropic description of damage in concrete structures.” Mech. Cohes.-Frict. Mater., 4(4), 339–359.
Garboczi, E. J., and Bentz, D. P. (1997). “Analytical formulas for interfacial transition zone properties.” Adv. Cement Based Mater., 6(3), 99–108.
Gawin, D., Pesavento, F., and Schrefler, B. A. (2006a). “Hygro-thermo-chemo-mechanical modelling of concrete at early ages and beyond. I: Hydration and hygro-thermal phenomena.” Int. J. Numer. Methods Eng., 67(3), 299–331.
Gawin, D., Pesavento, F., and Schrefler, B. A. (2006b). “Hygro-thermo-chemo-mechanical modelling of concrete at early ages and beyond. Part II: Shrinkage and creep of concrete.” Int. J. Numer. Methods Eng., 67(3), 332–363.
Grasberger, S., and Meschke, G. (2004). “Thermo-hygro-mechanical degradation of concrete: From coupled 3D material modelling to durability oriented multifield structural analyses. Mater. Struct., 37(4), 244–256.
Grassl, P., and Pearce, C. (2010). “Mesoscale approach to modeling concrete subjected to thermomechanical loading.” J. Eng. Mech., 136(3), 322–328.
Grassl, P., Wong, H. S., and Buenfeld, N. R. (2010). “Influence of aggregate size and volume fraction on shrinkage induced micro-cracking of concrete and mortar.” Cement Concr. Res., 40(1), 85–93.
Grondin, F., Dumontet, H., Ben Hamida, A., and Boussa, H. (2011). “Micromechanical contributions to the behavior of cement-based materials: Two-scale modelling of cement paste and concrete in tension at high temperatures.” Cement Concr. Compos., 33(3), 424–435.
Hager, I. (2004). “Comportement à haute température des bétons à haute performance - évolution des principales propriétés mécaniques.” Ph.D. thesis, l’Ecole Nationale des Ponts et Chaussées, Paris (in French).
Heinfling, G. (1997). “Contribution à la modélisation numerique du comportement du béton et des structures en béton armé sous sollicitations thermo-mécaniques à hautes températures.” Ph.D. thesis, Institut National des Sciences Appliquées de Lyon, Villeurbanne, France (in French).
Helmuth, R. A., and Turk, D. H. (1966). “Elastic moduli of hardened portland cement and tricalcium silicate pastes: Effect of porosity.” Proc., Symp. on Structure of Portland Cement Paste and Concrete, Vol. 90, Highway Research Board, Washington, DC, 135–144.
Hilaire, A., Benboudjema, F., Darquennes, A., and Berthaud, Y. (2012). “Modeling basic creep in concrete at early-age in compression and tension.” Proc., Conf. on Numerical Modeling Strategies for Sustainable Concrete Structures, Institute of Science and Technology for Transport, Spatial Planning, Development and Networks, Versailles, France.
Hobbs, D. W. (1974). “Influence of aggregate restraint on the shrinkage of concrete.” ACI J., 71(9), 445–450.
Hubert, F.-X., Burlion, N., and Shao, J. F. (2003). “Drying of concrete: Modelling of a hydric damage.” Mater. Struct., 36(1), 12–21.
Idiart, A., Bisschop, J., Caballero, A., and Lura, P. (2012). “A numerical and experimental study of aggregate-induced shrinkage cracking in cementitious composites.” Cement Concr. Res., 42(2), 272–281.
Ithurralde, G. (1989). “La perméabilité vue par le maître d'ouvrage.” Rep. Prepared for the Colloque Béton á Hautes Performances, Ecole Normal Supérieure, Paris (in French).
Lackner, R., and Mang, H. A. (2004). “Chemoplastic material model for the simulation of early-age cracking: From the constitutive law to numerical analyses of massive concrete structures.” Cement Concr. Compos., 26(5), 551–562.
Lagier, F., Jourdain, X., De Sa, C., Benboudjema, F., and Colliat, J. B. (2011). “Numerical strategies for prediction of drying cracks in heterogeneous materials: Comparison upon experimental results.” Eng. Struct., 33(3), 920–931.
Laplante, P., and Boulay, C. (1994). “Evolution du coefficient de dilatation thermique du béton en fonction de sa maturité aux tout premiers âges.” Mater. Struct., 27(10), 596–605 (in French).
Leite, J. P. B., Slovik, V., and Apel, J. (2007). “Computational model of mesoscopic structure of concrete for simulation of fracture processes.” Comp. Struct., 85(17–18), 1293–1303.
Leite, J. P. B., Slovik, V., and Mihashi, H. (2004). “Computer simulation of fracture processes of concrete using mesolevel models of lattice structures.” Cement Concr. Res., 34(6), 1025–1033.
Matallah, M., La Borderie, C., and Maurel, O. (2010). “A practical method to estimate crack openings in concrete structures.” Int. J. Numer. Anal. Methods Geomech., 34(15), 1615–1633.
Mazars, J. (1986). “A description of micro and macroscale damage of concrete structures.” Eng. Fract. Mech., 25(5–6), 729–737.
Mazzotti, C., and Savoia, M. (2003). “Nonlinear creep damage model for concrete under uniaxial compression.” J. Eng. Mech., 219(9), 1065–1075.
Mori, T., and Tanaka, K. (1973). “Average stress in matrix and average elastic energy of materials with misfitting inclusions.” Acta Metall., 21(5), 571–574.
Mounanga, P., Baroghel-Bouny, V., Loukili, A., and Khelidj, A. (2006). “Autogenous deformations of cement pastes. I: Temperature effects at early age and micro–macro correlations.” Cement Concr. Res., 36(1), 110–122.
Nguyen, T. D., Lawrence, C., La Borderie, C., Matallah, M., and Nahas, G. (2010). “A mesoscopic model for a better understanding of the transition from diffuse damage to localized damage.” Eur. J. Environ. Civil Eng., 14(6–7), 751–776.
Omar, M., Loukili, A., Pijaudier-Cabot, G., and Le Pape, Y. (2009). “Creep-damage coupled effects: Experimental investigation on bending beams with various sizes.” J. Mater. Civ. Eng., 21(2), 65–72.
Pichler, B., and Hellmich, C. (2011). “Upscaling quasi-brittle strength of cement paste and mortar: A multi-scale engineering mechanics model.” Cement Concr. Res., 41(5), 467–476.
Pichler, B., Hellmich, C., and Eberhardsteiner, J. (2009). “Spherical and acicular representation of hydrates in a micromechanical model for cement paste: Prediction of early-age elasticity and strength.” Acta Mech., 203(3–4), 137–162.
Pijaudier-Cabot, G., and Bažant, Z. P. (1987). “Nonlocal damage theory.” J. Eng. Mech., 113(10), 1512–1533.
Reviron, N. (2009). “Study of creep of concrete in tension: Application to nuclear pressurized water containment.” Ph.D. thesis, ENS Cachan, LMT, Paris (in French).
Rots, J. G. (1988). “Computational modeling of concrete fracture.” Ph.D. dissertation, Delft Univ. of Technology, Delft, Netherlands.
Sanahuja, J., Dormieux, L., and Chanvillard, G. (2007). “Modelling elasticity of a hydrating cement paste.” Cement Concr. Res., 37(10), 1427–1439.
Schlangen, E., Leegwater, G., and Koenders, E. A. B. (2006). “Modelling of autogenous shrinkage of concrete based on paste measurements.” Proc., 2nd Int. Symp. on Advances in Concrete through Science and Engineering, J. Marchand, B. Bissonnette, R. Gagné, M. Jolin, and F. Paradis, eds., RILEM Publications SARL, 207–224.
Smith, M. R., et al. (2001). Aggregates: Sand, gravel and crushed rock aggregates for construction purposes, 3rd Ed., Geological Society of London, London.
Stefan, L., Benboudjema, F., Torrenti, J. M., and Bissonnette, B. (2010). “Prediction of elastic properties of cement pastes at early ages.” Comput. Mater. Sci., 47(3), 775–784.
Taplin, J. M. (1959). “A method of following the hydration reaction in portland cement paste.” Aust. J. Appl. Sci., 10(3), 329–345.
Torrenti, J. M., Nguyen, V. H., Colina, H., Le Maou, F., Benboudjema, F., and Deleruyelle, F. (2008). “Coupling between leaching and creep of concrete.” Cement Concr. Res., 38(6), 816–821.
Ulm, F.-J., and Coussy, O. (1998). “Couplings in early-age concrete: From material modelling to structural design.” Int. J. Solids Struct., 35(31–32), 4295–4311.
Yssorche-Cubaines, M. P., and Ollivier, J. P. (1999). “La microfissuration d’autodessiccation et la durabilité des BHP et BTHP.” Mater. Struct., 32(1), 14–21.
Information & Authors
Information
Published In
Journal of Engineering Mechanics
Volume 139 • Issue 12 • December 2013
Pages: 1808 - 1817
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Aug 28, 2012
Accepted: Feb 13, 2013
Published online: Feb 15, 2013
Published in print: Dec 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.