Microplane Model M7 for Plain Concrete. II: Calibration and Verification
Publication: Journal of Engineering Mechanics
Volume 139, Issue 12
Abstract
The microplane material model for concrete, formulated mathematically in the companion paper, is calibrated by material test data from all the typical laboratory tests taken from the literature. Then, the model is verified by finite-element simulations of data for some characteristic tests with highly nonuniform strain fields. The scaling properties of model M7 are determined. With the volumetric stress effect taken from the previous load step, the M7 numerical algorithm is explicit, delivering in each load step the stress tensor from the strain tensor with no iterative loop. This makes the model robust and suitable for large-scale finite-element computations. There are five free, easily adjustable material parameters, which make it possible to match the given compressive strength, the corresponding strain, the given hydrostatic compression curve, and certain triaxial aspects. In addition, there are many fixed, hard-to-adjust parameters, which can be taken to be the same for all concretes. The optimum values of material parameters are determined by fitting a particularly broad range of test results, including the important tests of compression-tension load cycles, mixed-mode fracture, tension-shear failure of double-edge-notched specimens, and vertex effect when axial compression is followed by torsion. Because of the lack of information on the material characteristic length or fracture energy, which can be obtained only by size effect tests on the same concrete, and on the precise boundary conditions and precise gauge locations, the finite-element fitting of the present test data can hardly be expected to give better results than single-point simulations of specimens with approximately homogeneous strain states within the gauge length. Nevertheless, tensile test data with severe localization are delocalized on the basis of assumed material length. Model M7 is shown to fit a considerably broader range of test data than the preceding models M1–M6.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support under grant W911NF-09-1-0043/P00003 from the U.S. Army Research Office, Durham, North Carolina, to Northwestern University is gratefully acknowledged, and so is additional support for theoretical studies of the microplane model granted to Northwestern University through Daejeon University by the Agency for Defense Development (ADD), Korea.
References
ABAQUS 6.11 [Computer software]. Vélizy-Villacoublay, France, Dassault Systèmes.
Balmer, G. G. (1949). “Shearing strength of concrete under high triaxial stress computation of Mohr’s envelope as a curve.” Rep. No. SP-23, Structural Research Laboratory, Bureau of Reclamation, U.S. Dept. of the Interior, Denver.
Bažant, Z., and Yu, Q. (2011). “Size effect testing of cohesive fracture parameters and non-uniqueness of work-of-fracture method.” J. Eng. Mech., 137(8), 580–588.
Bažant, Z. P., Bishop, F. C., and Chang, T.-P. (1986). “Confined compression tests of cement paste and concrete up to 300 ksi.” J. Am. Concr. Inst., 33(4), 553–560.
Bažant, Z. P., and Caner, F. C. (2005). “Microplane model M5 with kinematic and static constraints for concrete fracture and anelasticity. II. Computation.” J. Eng. Mech., 131(1), 41–47.
Bažant, Z. P., and Cedolin, L. (1991). Stability of structures: Elastic, damage theories, Oxford University Press, New York.
Bažant, Z. P., and Oh, B.-H. (1983). “Crack band theory for fracture of concrete.” Matér. Struct., 16(3), 155–177.
Bažant, Z. P., and Oh, B.-H. (1986). “Efficient numerical integration on the surface of a sphere.” Z. Angew. Math. Mech., 66(1), 37–49.
Bažant, Z. P., Xiang, Y., Adley, M. D., Prat, P. C., and Akers, S. A. (1996). “Microplane model for concrete. II. Data delocalization and verification.” J. Eng. Mech., 122(3), 255–262.
Bresler, B., and Pister, K. S. (1958). “Strength of concrete under combined stresses.” J. Am. Concr. Inst., 551(9), 321–345.
Brocca, M., and Bažant, Z. P. (2000). “Microplane constitutive model and metal plasticity.” Appl. Mech. Rev., 53(10), 265–281.
Budianski, B. (1959). “A reassessment of deformation theories of plasticity.” J. Appl. Mech., 26(2), 259–264.
Caner, F., Bažant, Z., and Červenka, J. (2002). “Vertex effect in strain-softening concrete at rotating principal axes.” J. Eng. Mech., 128(1), 24–33.
Caner, F. C., and Bažant, Z. P. (2013). “Microplane model M7 for plain concrete. I: Formulation.” J. Eng. Mech., 139(12), 1714–1723.
Chern, J.-C., Yang, H.-J., and Chen, H.-W. (1992). “Behavior of steel fiber-reinforced concrete in multiaxial loading.” ACI Mater. J., 89(1), 32–40.
Cusatis, G., Bažant, Z. P., and Cedolin, L. (2003). “Confinement–shear lattice model for concrete damage in tension and compression: I. Theory.” J. Eng. Mech., 129(12), 1439–1448.
Cusatis, G., Mencarelli, A., Pelessone, D., and Baylot, J. T. (2011a). “Lattice discrete particle model (LDPM) for failure behavior of concrete. II: Calibration and validation.” Cement Concr. Compos., 33(9), 891–905.
Cusatis, G., Pelessone, D., and Mencarelli, A. (2011b). “Lattice discrete particle model (LDPM) for failure behavior of concrete. I: Theory.” Cement Concr. Compos., 33(9), 881–890.
Gálvez, J., Elices, M., Guinea, G., and Planas, J. (1998). “Mixed mode fracture of concrete under proportional and nonproportional loading.” Int. J. Fract., 94(3), 267–284.
Gasser, T. C., and Holzapfel, G. A. (2006). “3D crack propagation in unreinforced concrete: A two-step algorithm for tracking 3D crack paths.” Comput. Methods Appl. Mech. Eng., 195(37–40), 5198–5219.
Gerard, G., and Becker, H. (1957). “Handbook of structural stability: Part I. Buckling of flat plates.” NACA Technical Note 3781, National Advisory Committee for Aeronautics, Washington, DC.
Green, S. J., and Swanson, S. R. (1973). “Static constitutive relations for concrete.” Rep. No. AFWL-TR-72-2, Air Force Weapons Laboratory, Kirtland Air Force Base, Albuquerque, NM.
Jirásek, M., and Zimmermann, T. (1998). “Analysis of rotating crack model.” J. Eng. Mech., 124(8), 842–851.
Kupfer, H., Hilsdorf, H. K., and Rüsch, H. (1969). “Behavior of concrete under biaxial stresses.” J. Am. Concr. Inst., 66(8), 656–666.
Launay, P., and Gachon, H. (1971). “Strain and ultimate strength of concrete under triaxial stress.” Proc., 1st Int. Conf. on Structural Mechanics in Reactor Technology (SMiRT1), T. Jaeger, ed., Commission of European Communities, Brussels, Belgium.
Li, F., and Li, Z. (2000). “Continuum damage mechanics based modeling of fiber-reinforced concrete in tension.” Int. J. Solids Struct., 38(5), 777–793.
Li, Z., Li, F., Chang, T.-Y.-P., and Mai, Y.-W. (1998). “Uniaxial tensile behavior of concrete reinforced with randomly distributed short fibers.” ACI Mater. J., 95(5), 564–574.
Nooru-Mohamed, M. (1992). “Mixed mode fracture of concrete: An experimental approach.” Ph.D. thesis, Delft Univ. of Technology, Delft, Netherlands.
Petersson, P. E. (1981). “Crack growth and development of fracture zones in plain concrete and similar materials.” Rep. No. TVBM 1006, Lund Institute of Technology, Lund, Sweden.
Pivonka, P., Ožbolt, J., Lackner, R., and Mang, H. A. (2004). “Comparative studies of 3D-constitutive models for concrete: Application to mixed-mode fracture.” Int. J. Numer. Methods Eng., 60(2), 549–570.
Reinhardt, H. W., and Cornelissen, H. A. W. (1984). “Post-peak cyclic behavior of concrete in uniaxial tensile and alternating tensile and compressive loading.” Cement Concr. Res., 14(2), 263–270.
Sinha, B. P., Gerstle, K. H., and Tulin, L. G. (1964). “Stress-strain relations for concrete under cyclic loading.” J. Am. Concr. Inst., 62(2), 195–210.
van Mier, J. G. M. (1984). “Strain-softening of concrete under multiaxial loading conditions.” Ph.D. thesis, Die Technische Hogeschool Eindhoven, Eindhoven, Netherlands.
van Mier, J. G. M. (1986a). “Multiaxial strain-softening of concrete. I: Fracture.” Mater. Struct., 19(3), 179–190.
van Mier, J. G. M. (1986b). “Multiaxial strain-softening of concrete. II: Load histories.” Mater. Struct., 19(3), 190–200.
Yin, W. S., Su, E. C. M., Mansur, M. A., and Hsu, T. T. C. (1989). “Biaxial tests of plain and fiber concrete.” ACI Mater. J., 86(3), 236–243.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 23, 2012
Accepted: Nov 16, 2012
Published online: Nov 20, 2012
Published in print: Dec 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.