Reliability Assessment of Damaged RC Moment-Resisting Frame against Progressive Collapse under Static Loading Conditions
Publication: Journal of Engineering Mechanics
Volume 139, Issue 1
Abstract
Prevention of structures against progressive collapse has become a concern of increasing significance and the alternative load path method (ALPM) is the extensively acknowledged approach in this area of research. With the basis of ALPM and by amalgamation of the Monte Carlo simulation method and an iterative algorithm, a new approach is developed in this paper to assess the reliability of ductile RC frame structures when subjected to one column failure. This paper focuses on the construction and solution of the performance function of the damaged structure under static service loadings. With this intention, three types of critical zones are identified and an optimum model is presented to determine the possible failure modes for each zone. By employing the virtual work principle and critical collapse mechanism criterion, the performance function is established in terms of minimum internal virtual work and external virtual work done by service loadings. Three equations containing the interaction between the axial forces and bending strength of structural members are evolved to calculate this function, and by solving these equations from the top floor to the floor of the failed column the performance of the damaged structure can be appraised.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASCE. (1995). “Minimum design loads for buildings and other structures.” ASCE 7-95, New York.
ASCE. (2002). “Minimum design loads for buildings and other structures.” ASCE 7-02, New York.
Biggs, J. M. (1964). Introduction to structural dynamics, McGraw Hill, New York.
Comité Euro-International du Béton (CEB). (1993). “CEB-FIP Model Code 1990.” CEB Bulletin d’Information No. 213/213, Lausanne, Switzerland.
Department of Defense (DoD). (2001). DoD interim antiterrorism/force protection construction standards—Progressive collapse design guidance, DoD, Washington, DC.
Ellingwood, B., and Dusenberry, D. (2005). “Building design for abnormal loads and progressive collapse.” Comput. Aided Civ. Infrastruct. Eng., 20(3), 194–205.
European Committee for Standardization (CEN). (1996). “Design of concrete structures.” Eurocode 2, Brussels, Belgium.
General Services Administration (GSA). (2000). Progressive collapse analysis and design guidelines for new federal office buildings and major modernization projects, GSA, Washington, DC.
Huang, Z. W. (2008). “Reliability assessment of damaged ductile RC frame structures against progressive collapse in close-in detonation conditions.” Ph.D. thesis, Nanyang Technological Univ., Singapore.
Israel, M., Ellingwood, B., and Corotis, R. (1987). “Reliability-based code formulations for reinforced concrete buildings.” J. Struct. Div., 113(10), 2235–2252.
Kaewkulchai, G. (2003). “Dynamic progressive collapse of frame structures.” Ph.D. dissertation, Univ. of Texas at Austin, Austin, TX.
Kaewkulchai, G., and Williamson, E. B. (2006). “Modeling the impact of failed members for progressive collapse analysis of frame structures.” J. Perform. Constr. Facil., 20(4), 375–383.
MacGregor, J. G., Mirza, S. A., and Ellingwood, B. (1983). “Statistical analysis of resistance of reinforced and prestressed concrete members.” ACI J., 80(3), 167–176.
Marjanishvili, S. M. (2004). “Progressive analysis procedure for progressive collapse.” J. Perform. Constr. Facil., 18(2), 79–85.
May, G. C., and Smith, P. D. (1995). Blast effects on buildings: Design of buildings to optimize resistance to blast loading, Thomas Telford, New York.
Mirza, S. A., Hatzinikolas, M., and MacGregor, J. G. (1979). “Statistical description of strength of concrete.” J. Struct. Div., 105(6), 1021–1037.
Mirza, S. A., and MacGregor, J. G. (1979). “Variations in dimensions of reinforced concrete members.” J. Struct. Div., 105(4), 751–766.
Newmark, N. M. (1972). “External blast.” Proc., Int. Conf. on the Planning and Design of Tall Buildings, Vol. Ib, Lehigh Univ., Bethlehem, PA, 661–676.
Pretlove, A. J., Ramsden, M., and Atkins, A. G. (1991). “Dynamic effects in progressive failure of structures.” Int. J. Impact Eng., 11(4), 539–546.
Sasani, M., Kazemi, A., Sagiroglu, S. G., and Forest, S. (2011). “Progressive collapse of an actual 11-story structure subjected to severe initial damage.” J. Struct. Eng., 137(9), 893–902.
Sucuoğlu, H., Cıtıpıtıoğlu, E., and Altin, S. (1994). “Resistance mechanisms in RC building frames subjected to column failure.” J. Struct. Eng., 120(3), 765–782.
U.S. Department of the Army (USDA). (1986). “Fundamental of protective design for conventional weapons.” TM 5-855-1, Washington, DC.
U.S. Department of the Army (USDA). (1990). “Structures to resist the effects of accidental explosions. Vol. IV. Reinforced concrete design.” TM5-1300, Washington, DC.
Val, D., Bljuger, F., and Yankelevsky, D. (1997a). “Reliability assessment of damaged RC framed structures”. J. Struct. Eng., 123(7), 889–895.
Val, D., Bljuger, F., and Yankelevsky, D. (1997b). “Reliability evaluation in nonlinear analysis of reinforced concrete structures.” Struct. Safety, 19(2), 203–217.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 22, 2010
Accepted: Apr 18, 2012
Published online: Apr 20, 2012
Published in print: Jan 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.