Load Transfer and Recovery Length in Parallel Wires of Suspension Bridge Cables
Publication: Journal of Engineering Mechanics
Volume 137, Issue 4
Abstract
A new simplified contact model aimed at capturing the load transfer and recovery length in parallel steel wires, commonly used in main cables of suspension bridges, is presented. The approach is based on placing elastic–perfectly plastic spring elements at the contact region between the objects. These springs have varying stiffness (Model I) or yielding (Model II) depending on their proximity to the clamping loads. Their stiffness or yielding is highest when they are closer to this force, and it decays when they are farther away from the clamp. This decayed behavior is assigned according to Boussinesq’s well-known solution to a point load (applied on a half space). Both models converge quickly compared with a full contact model and recover Coulomb friction law on a two-dimensional (2D) benchmark problem. Moreover, when the same properties are chosen for all springs (disregarding Boussinesq solutions), the models reduce to the classical shear-lag model, which for high clamping (point) loads gives inaccurate results. The spring models are validated experimentally on a seven-wire tightened strand. In this case study, the outer wires are axially pulled, whereas the middle wire, slightly shorter than the outer wires, experiences no direct applied axial load. However, because the strand is radially fastened at several locations, the axial load is transferred to the inner wire by an interfriction mechanism between the wires. The strains at the center points of the outer and inner wires are measured via neutron diffraction for different clamping loads, showing that the inner wire is capable of recovering most of the load.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers wish to thank Dr. Bojidar Yanev of the New York City DOT for intriguing discussions and excellent suggestions on the modeling and analysis of this problem.
References
ABAQUS [Computer software]. Version 6.8, Hibbitt, Karlson and Sorensen, Pawtucket, RI.
Barton, S. C., Vermaas, G. W., Duby, P. F., West, A. C., and Betti, R. (2000). “Accelerated corrosion and embrittlement of high-strength bridge wire.” J. Mech. Civ. Eng., 12(1), 33–38.
Betti, R., and Yanev, B. (1999). “Conditions of suspension bridge cables: The New York City case study.” Transportation Research Record 1654, Transportation Research Board, Washington, DC, 12, 105–112.
Chien, C., and Costello, G. A. (1985). “Effective length of a fractured wire in wire rope.” J. Eng. Mech., 111(7), 952–961.
Costello, G. (1990). Theory of wire rope, Springer, New York.
Cox, H. L. (1952). “The elasticity and strength of paper and other fibrous materials.” Br. J. Appl. Phys., 3, 72–79.
Gjelsvik, A. (1991). “Development length for single wire in suspension bridge cable.” J. Struct. Eng., 117(4), 1189–1200.
Goland, M., and Reissner, E. (1944). “Stresses in cemented joints.” J. Appl. Mech., 11, A17–A27.
Huang, X. L., and Vinogradov, O. G. (1996a). “Dry friction losses in axially loaded cables.” Struct. Eng. Mech., 4(3), 330–344.
Huang, X. L., and Vinogradov, O. G. (1996b). “Extension of a cable in the presence of dry friction.” Struct. Eng. Mech., 4(3), 313–329.
Labrosse, M., Nawrocki, A., and Conway, T. (2000). “Frictional dissipation in axially loaded simple straight strands.” J. Eng. Mech., 126(6), 641–646.
Murray, C. E., Yan, H. F., Noyan, I. C., Cai, Z., and Lai, B. (2002). “Finite-size effects in thin-film composites.” Philos. Mag. A, 82(16), 3087–3117.
Murray, C. E., Yan, H. F., Noyan, I. C., Cai, Z., and Lai, B. (2005). “High-resolution strain mapping in heteroepitaxial thin-film features.” J. Appl. Phys., 98(1), 013504.
Nawrocki, A., and Labrosse, M. (2000). “A finite element model for simple straight wire rope strands.” Comput. Struct., 77(4), 345–349.
Noyan, I. C., Brügger, A., Betti, R., and Clausen, B. (2009). “Measurement of strain/load transfer in parallel seven-wire strands with neutron diffraction.” Exp. Mech., 50(2), 265–272.
Raoof, M. (1991). “Wire recovery length in helical strand under axial-fatigue loading.” Int. J. Fatigue, 13(2), 127–132.
Raoof, M., and Huang, Y. P. (1992). “Wire recovery length in suspension bridge cable.” J. Struct. Eng., 118(12), 3255–3267.
Raoof, M., and Kraincanic, I. (1998). “Determination of wire recovery length in steel cables.” Comput. Struct., 68(5), 445–459.
Taya, M., and Arsenault, R. J. (1987). “A comparison between a shear lag type model and an eshelby type model in predicting the mechanical properties of a short fiber composite.” Scr. Metall., 21, 349–354.
Timoshenko, S., and Goodier, J. (1970). Theory of elasticity, 2nd Ed., McGraw-Hill, New York.
Timoshenko, S., and Krieger, S. W. (1959). Theory of plates and shells, 2nd Ed., McGraw-Hill, New York.
Utting, W. S., and Jones, N. (1987a). “The response of wire rope strands to axial tensile loads—Part I. Experimental results and theoretical predictions.” Int. J. Mech. Sci., 29(9), 605–619.
Utting, W. S., and Jones, N. (1987b). “The response of wire rope strands to axial tensile loads—Part II. Comparison of experimental results and theoretical predictions.” Int. J. Mech. Sci., 29(9), 621–636.
Volkersen, O. (1938). “Die nietkraftverteilung in zugbeanspruchten nietverbindungen mit konstanten laschen-querschnitten.” Luftfahrtforschung, 15, 4147 (in German).
Wriggers, P. (2006). Computational contact mechanics, 2nd Ed., Springer, New York.
Xavier, C. L., and de la Vallée Poussin, J. (2000). “Environmental deterioration effects in bridge wires.” Research program on environmental and stress deterioration of wires in cables of suspension bridges, Columbia Univ., New York.
Yuwei, S., Deodatis, G., and Betti, R. (2007). “Random field-based approach for strength evaluation of suspension bridge cables.” J. Struct. Eng., 133(12), 1690–1699.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Aug 2, 2009
Accepted: Aug 30, 2010
Published online: Sep 10, 2010
Published in print: Apr 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.