Modeling Adsorption Isotherm for Defluoridation by Calcined : State-of-the-Art Technique
Publication: Journal of Environmental Engineering
Volume 144, Issue 2
Abstract
The calcined layered double hydroxide (LDH) was synthesized by a coprecipitation method and was applied for the adsorptive removal of fluoride from the aqueous solution. The isotherm experiments were conducted in the various initial fluoride concentration ranges. The estimation of isotherm parameters from the various isotherm models as well as the adequacy of these models exhibited the significant variation in the different concentration ranges. A generalized isotherm model was employed based on the Langmuir and Freundlich isotherms. The proposed model segregates the adsorption from the other influencing factors. The model was applied in different concentration ranges and provides maximum adsorption capacity as 351.066, 364.868, and in the concentration ranges of 0–10, 0–100, and . However, the same was found as 8.964, , and from the Langmuir isotherm. The significant variation of the isotherm parameters in the different concentration ranges clearly indicates an ambiguity in this field. The proposed model overcomes the drawback associated with the estimation of the isotherm parameters and can be applied as a generalized model to demonstrate the adsorption equilibrium.
Get full access to this article
View all available purchase options and get full access to this article.
References
Allen, S. J., McKay, G., and Porter, J. F. (2004). “Adsorption isotherm models for basic dye adsorption by peat in single and binary component systems.” J. Colloid Interface Sci., 280(2), 322–333.
Altundoǧan, H. S., Altundoǧan, S., Tümen, F., and Bildik, M. (2000). “Arsenic removal from aqueous solutions by adsorption on red mud.” Waste Manage., 20(8), 761–767.
Atkins, P., and de Paula, J. (2006). Atkins’ physical chemistry, Oxford University Press, Oxford, U.K.
Ayoob, S., and Gupta, A. K. (2006). “Fluoride in drinking water: A review on the status and stress effects.” Crit. Rev. Environ. Sci. Technol., 36(6), 433–487.
Ayoob, S., and Gupta, A. K. (2007). “Sorptive response profile of an adsorbent in the defluoridation of drinking water.” Chem. Eng. J., 133(1–3), 273–281.
Ayoob, S., and Gupta, A. K. (2008). “Insights into isotherm making in the sorptive removal of fluoride from drinking water.” J. Hazard. Mater., 152(3), 976–985.
Ayoob, S., and Gupta, A. K. (2009). “Performance evaluation of alumina cement granules in removing fluoride from natural and synthetic waters.” Chem. Eng. J., 150(2), 485–491.
Ayoob, S., Gupta, A. K., and Bhat, V. T. (2008). “A conceptual overview on sustainable technologies for the defluoridation of drinking water.” Crit. Rev. Environ. Sci. Technol., 38(6), 401–470.
Batistella, L., et al. (2011). “Evaluation of acid activation under the adsorption capacity of double layered hydroxides of type for fluoride removal from aqueous medium.” Ind. Eng. Chem. Res., 50(11), 6871–6876.
Bhatnagar, A., Kumar, E., and Sillanpää, M. (2011). “Fluoride removal from water by adsorption—A review.” Chem. Eng. J., 171(3), 811–840.
Brunson, L. R., and Sabatini, D. A. (2015). “Role of surface area and surface chemistry during an investigation of eucalyptus wood char for fluoride adsorption from drinking water.” J. Environ. Eng., 4014060.
Brunson, L. R., and Sabatini, D. A. (2016). “Methods for optimizing activated materials for removing fluoride from drinking water sources.” J. Environ. Eng., 4015078.
Cai, P., et al. (2012). “Competitive adsorption characteristics of fluoride and phosphate on calcined layered double hydroxides.” J. Hazard. Mater., 213–214, 100–108.
Cape, J. N., Fowler, D., and Davison, A. (2003). “Ecological effects of sulfur dioxide, fluorides, and minor air pollutants: Recent trends and research needs.” Environ. Int., 29(2–3), 201–211.
Carr, R., Comer, J., Ginsberg, M. D., and Aksimentiev, A. (2011). “Microscopic perspective on the adsorption isotherm of a heterogeneous surface.” J. Phys. Chem. Lett., 2(14), 1804–1807.
Cavani, F., Trifirò, F., and Vaccari, A. (1991). “Hydrotalcite-type anionic clays: Preparation, properties and applications.” Catal. Today, 11(2), 173–301.
Craig, L., Stillings, L. L., Decker, D. L., and Thomas, J. M. (2015). “Comparing activated alumina with indigenous laterite and bauxite as potential sorbents for removing fluoride from drinking water in Ghana.” Appl. Geochem., 56, 50–66.
Davis, C. W., and Di Toro, D. M. (2015). “Modeling nonlinear adsorption to carbon with a single chemical parameter: A lognormal langmuir isotherm.” Environ. Sci. Technol., 49(13), 7810–7817.
Du, J., Sabatini, D. A., and Butler, E. C. (2016). “Preparation, characterization, and regeneration of aluminum (hydr)oxide-amended molecular sieves for fluoride removal from drinking water.” J. Environ. Eng., 4016043.
Du, J., Sabatini, D. A., and Butler, E. C. (2017). “Evaluation of aluminum hydroxide-amended zeolites in fluoride removal: Column filtration and regeneration.” J. Environ. Eng., 4016092.
Dubinin, M. M., and Radushkevich, L. V. (1947). “The equation of the characteristic curve of the activated charcoal.” Proc., Academy of Sciences of the USSR, Physical Chemistry Section, Vol. 55, Scientific Research Publishing, Wuhan, China, 331–337.
Foo, K. Y., and Hameed, B. H. (2010). “Insights into the modeling of adsorption isotherm systems.” Chem. Eng. J., 156(1), 2–10.
Freundlich, H. M. F. (1906). “Over the adsorption in solution.” J. Phys. Chem., 57, 385–471.
Ghosal, P. S., and Gupta, A. K. (2015). “An insight into thermodynamics of adsorptive removal of fluoride by calcined layered double hydroxide.” RSC Adv., 5(128), 105889–105900.
Ghosal, P. S., and Gupta, A. K. (2016). “Enhanced efficiency of ANN using non-linear regression for modeling adsorptive removal of fluoride by calcined .” J. Mol. Liq., 222, 564–570.
Ghosal, P. S., and Gupta, A. K. (2017a). “Determination of thermodynamic parameters from Langmuir isotherm constant-revisited.” J. Mol. Liq., 225, 137–146.
Ghosal, P. S., and Gupta, A. K. (2017b). “Development of a generalized adsorption isotherm model at solid-liquid interface: A novel approach.” J. Mol. Liq., 240, 21–24.
Ghosal, P. S., Gupta, A. K., and Ayoob, S. (2015). “Effect of formation pH, molar ratio and calcination temperature on the synthesis of an anionic clay based adsorbent targeting defluoridation.” Appl. Clay Sci., 116–117, 120–128.
Ghosh, D., Sinha, M. K., and Purkait, M. K. (2013). “A comparative analysis of low-cost ceramic membrane preparation for effective fl uoride removal using hybrid technique.” Desalination, 327, 2–13.
Gupta, A. K., and Ayoob, S. (2016). Fluoride in drinking water: Status, issues, and solutions, CRC Press, New York.
Gupta, A. K., Ghosal, P. S., and Srivastava, S. K. (2016). “Modeling and optimization of defluoridation by calcined using response surface methodology and artificial neural network combined with experimental design.” J. Hazard. Toxic Radioact. Waste, 4016024.
He, J., Wei, M., Li, B., Kang, Y., Evans, D. G., and Duan, X. (2006). “Preparation of layered double hydroxides.” Structure and bonding, X. Duan and D. G. Evans, eds., Springer, Berlin, 89–119.
Hill, A. V. (1910). “The possible effects of the aggregation of the molecules of haemoglobin on its dissociation curves.” J. Physiol. (London), 40, iv–vii.
Horsfall, M., Jr., and Spiff, I. (2005). “Equilibrium sorption study of , and in aqueous solutions by fluted pumpkin (Telfairia occidentalis Hook f) waste biomass.” Acta Chim. Slov., 52, 174–181.
Hou, D., Wang, J., Zhao, C., Wang, B., Luan, Z., and Sun, X. (2010). “Fluoride removal from brackish groundwater by direct contact membrane distillation.” J. Environ. Sci., 22(12), 1860–1867.
Kang, D., et al. (2013). “Performance and mechanism of Mg/Fe layered double hydroxides for fluoride and arsenate removal from aqueous solution.” Chem. Eng. J., 228, 731–740.
Khan, A., Ataullah, R., and Al-Haddad, A. (1997). “Equilibrium adsorption studies of some aromatic pollutants from dilute aqueous solutions on activated carbon at different temperatures.” J. Colloid Interface Sci., 194(1), 154–165.
Koble, R. A., and Corrigan, T. E. (1952). “Adsorption isotherms for pure hydrocarbons.” Ind. Eng. Chem., 44(2), 383–387.
Kundu, S., and Gupta, A. K. (2006). “Arsenic adsorption onto iron oxide-coated cement (IOCC): Regression analysis of equilibrium data with several isotherm models and their optimization.” Chem. Eng. J., 122(1–2), 93–106.
Langmuir, I. (1916). “The constitution and fundamental properties of solids and liquids.” J. Am. Chem. Soc., 38(11), 2221–2295.
Limousin, G., Gaudet, J.-P., Charlet, L., Szenknect, S., Barthès, V., and Krimissa, M. (2007). “Sorption isotherms: A review on physical bases, modeling and measurement.” Appl. Geochem., 22(2), 249–275.
Liu, C.-C., and Liu, J. C. (2015). “Coupled precipitation-ultrafiltration for treatment of high fluoride-content wastewater.” J. Taiwan Inst. Chem. Eng., 58, 259–263.
Liu, Y. (2009). “Is the free energy change of adsorption correctly calculated?” J. Chem. Eng. Data, 54(7), 1981–1985.
Lv, L., He, J., Wei, M., Evans, D. G., and Zhou, Z. (2007). “Treatment of high fluoride concentration water by – layered double hydroxides: Kinetic and equilibrium studies.” Water Res., 41(7), 1534–1542.
Maiti, A., Basu, J. K., and De, S. (2011). “Chemical treated laterite as promising fluoride adsorbent for aqueous system and kinetic modeling.” Desalination, 265(1–3), 28–36.
Mandal, S., and Mayadevi, S. (2008). “Adsorption of fluoride ions by Zn-Al layered double hydroxides.” Appl. Clay Sci., 40(1–4), 54–62.
Mandal, S., and Mayadevi, S. (2009). “Defluoridation of water using as-synthesized Zn/Al/Cl anionic clay adsorbent: Equilibrium and regeneration studies.” J. Hazard. Mater., 167(1–3), 873–878.
Mandal, S., Tripathy, S., Padhi, T., Sahu, M. K., and Patel, R. K. (2013). “Removal efficiency of fluoride by novel Mg-Cr-Cl layered double hydroxide by batch process from water.” J. Environ. Sci., 25(5), 993–1000.
MATLAB version 7.10.0 [Computer software]. MathWorks, Natick, MA.
Medellin-Castillo, N. A., Leyva-Ramos, R., Padilla-Ortega, E., Perez, R. O., Flores-Cano, J. V., and Berber-Mendoza, M. S. (2014). “Adsorption capacity of bone char for removing fluoride from water solution. Role of hydroxyapatite content, adsorption mechanism and competing anions.” J. Ind. Eng. Chem., 20(6), 4014–4021.
Mlilo, T. B., Brunson, L. R., and Sabatini, D. A. (2010). “Arsenic and fluoride removal using simple materials.” J. Environ. Eng., 391–398.
Nechifor, G., Pascu, D. E., Neagu, M. P., Traistaru, G., and Albu, P. (2015). “Comparative study of Timken and Flory-Huggins isotherms for adsorption of phosphate anion on membranes.” UPB Sci. Bull. Ser. B Chem. Mater. Sci., 77(2), 63–72.
Palahouane, B., Drouiche, N., Aoudj, S., and Bensadok, K. (2015). “Cost-effective electrocoagulation process for the remediation of fluoride from pretreated photovoltaic wastewater.” J. Ind. Eng. Chem., 22, 127–131.
Redlich, O., and Peterson, D. L. (1959). “A useful adsorption isotherm.” J. Phys. Chem., 63(6), 1024.
Sandoval, M. A., Fuentes, R., Nava, J. L., and Rodríguez, I. (2014). “Fluoride removal from drinking water by electrocoagulation in a continuous filter press reactor coupled to a flocculator and clarifier.” Sep. Purif. Technol., 134, 163–170.
Sawyer, C. N., McCarty, P. L., and Parkin, G. F. (2002). Chemistry for environmental engineering and science, McGraw-Hill Education, New York.
Shen, J., and Schäfer, A. I. (2015). “Factors affecting fluoride and natural organic matter (NOM) removal from natural waters in Tanzania by nanofiltration/reverse osmosis.” Sci. Total Environ., 527–528, 520–529.
Sips, R. (1948). “Combined form of Langmuir and Freundlich equations.” J. Chem. Phys., 16(5), 490–495.
Tempkin, M. I., and Pyzhev, V. (1940). “Kinetics of ammonia synthesis on promoted iron catalyst.” Acta Phys. Chim. USSR, 12, 327–356.
Theiss, F. L., Couperthwaite, S. J., Ayoko, G. A., and Frost, R. L. (2014). “A review of the removal of anions and oxyanions of the halogen elements from aqueous solution by layered double hydroxides.” J. Colloid Interface Sci., 417, 356–368.
Tor, A. (2007). “Removal of fluoride from water using anion-exchange membrane under Donnan dialysis condition.” J. Hazard. Mater., 141(3), 814–818.
Toth, J. (1971). “State equations of the solid gas interface layer.” Acta Chem. Acad. Hung., 69, 311–317.
Vijayaraghavan, K., Padmesh, T. V. N., Palanivelu, K., and Velan, M. (2006). “Biosorption of nickel(II) ions onto Sargassum wightii: Application of two-parameter and three-parameter isotherm models.” J. Hazard. Mater., 133(1–3), 304–308.
Wan, D., Liu, Y., Xiao, S., Chen, J., and Zhang, J. (2015). “Uptake fluoride from water by caclined hydrotalcite: Mg/Al ratio effect on its structure, electrical affinity and adsorptive property.” Colloids Surf. A, 469, 307–314.
WHO (World Health Organization). (2011). Guidelines for drinking-water quality, 4th Ed., Geneva.
Yakub, I., and Soboyejo, W. (2013). “Adsorption of fluoride from water using sintered clay-hydroxyapatite composites.” J. Environ. Eng, 995–1003.
Zhang, T., Li, Q., Xiao, H., Lu, H., and Zhou, Y. (2012). “Synthesis of Li-Al layered double hydroxides (LDHs) for efficient fluoride removal.” Ind. Eng. Chem. Res., 51(35), 11490–11498.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Mar 28, 2017
Accepted: Jul 26, 2017
Published online: Nov 29, 2017
Published in print: Feb 1, 2018
Discussion open until: Apr 29, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.