Early Age Cracking Control in Semimassive Walls of RC Tanks by Internal Cooling
Publication: Journal of Performance of Constructed Facilities
Volume 35, Issue 4
Abstract
Semimassive tanks must satisfy the requirement of watertightness, so all attempts to reduce early-age imposed strains lead to considerable financial savings. The impact of a cooling pipe system (CPS) on a reinforced concrete (RC) tank wall where early-age cracks developed during construction has been analyzed. It has been proven that for RC tanks, the factor that contributes most to tensile stresses in the semimassive walls is the mean temperature of the maturing concrete. The second most influential factor is derived from self-stresses, and the least influential factor is the stress gradient. The calculations of self-stresses indicate that the use of a CPS leads to the formation of favorable compressive rather than tensile stresses in the central part of the wall. Most importantly, a CPS in RC tank walls significantly reduces the width of cracks that result from the cumulative effect of early-age and long-term imposed strains. The performed analysis provides a basis for the effective design of a CPS in RC tank semimassive walls.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
References
Aleksandrovski, S. V. 1966. Calculations of concrete and reinforced concrete structures subjected to temperature and humidity changes (including creep). Moskwa: Strojizdat.
Azenha, M., R. Lameiras, C. de Sousa, and J. Barros. 2014. “Application of air cooled pipes for reduction of early age cracking risk in a massive RC wall.” Eng. Struct. 62–63 (Mar): 148–163. https://doi.org/10.1016/j.engstruct.2014.01.018.
Bamforth, P. B. 2018. Control of cracking caused by restrained deformation in concrete. London: Construction Industry Research and Information Association.
Bofang, Z. 2014. Thermal stresses and temperature control of mass concrete. Oxford, UK: Butterworth-Heinemann.
CEN (European Committee for Standardization). 2004. Design of concrete structures: General rules and rules for buildings, part 1.1. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2006. Design of concrete structures: Liquid retaining and containment structures, part 3. Brussels, Belgium: CEN.
Chen, S., P. Su, and I. Shahrour. 2011. “Composite element algorithm for the thermal analysis of mass concrete.” Int. J. Numer. Methods Heat Fluid Flow 21 (4): 434–447. https://doi.org/10.1108/09615531111123100.
Fairbairn, E. M. R., and M. Azenha. 2019. Thermal cracking of massive concrete structures. State-of-the-art report of the RILEM Technical Committee 254-CMS. New York: Springer.
Flaga, K. 2004. Shrinkage stress and reinforcement in concrete structure. Monograph 295. Cracow, Poland: Cracow Univ. of Technology.
Hamfler, H. 1988. Berechnung von Temperatur-, Feuchte- und Verschie- bungsfeldern in erhärtenden Betonbauteilen nach der Methode der Finite Elemente” [Calculation of temperature, humidity and displacement in hardening concrete elements using the finite element method]. [In German.] Hannover, Germany: Institut für Massivbau.
Hauser, G., C. Kempkes, and B. W. Olesen. 2000. “Computer simulation of hydronic heating/cooling system with embedded pipes.” In Proc., ASHRAE Winter Meeting, American Society of Heating, Refrigerating and Air Conditioning Engineers, 702–710. Dallas: American Society of Heating, Refrigerating and Air Conditioning Engineers.
Hong, Y. X., W. Chen, J. Lin, and J. Gong. 2017. “Thermal field in water pipe cooling concrete hydrostructures simulated with singular boundary method.” Water Sci. Eng. 10 (2): 107–114. https://doi.org/10.1016/j.wse.2017.06.004.
Jędrzejewska, A., F. Kanavaris, M. Zych, D. Schlicke, and M. Azenha. 2020. “Experiences on early age cracking of wall-on-slab concrete structures.” In Vol. 27 of Structures, 2520–2549. London: Elsevier. https://doi.org/10.1016/j.istruc.2020.06.013.
JSCE (Japan Society of Civil Engineers). 2011. Guidelines for concrete. No. 15: Standard specifications for concrete structures. Design. Tokyo, Japan: JSCE.
Kanavaris, F., et al. 2021. “Enhanced massivity index based on evidence from case studies: Towards a robust pre-design assessment of early-age thermal cracking risk and practical recommendations.” Constr. Build. Mater. 271 (Feb): 121570. https://doi.org/10.1016/j.conbuildmat.2020.121570.
Knoppik-Wróbel, A. 2015. “Analysis of early-age thermal-shrinkage stresses in reinforced concrete walls.” Ph.D. thesis, Faculty of Civil Engineering, Silesian Univ. of Technology.
Kogan, E. A. 1980. “Stress relaxation in concrete of massive hydraulic structures.” Hydrotech. Constr. 14 (9): 916–920. https://doi.org/10.1007/BF02305447.
Li, C., and Y. Li. 2017. “Optimization of cooling pipes inside mass concrete bridge pile cap.” In Proc., 2nd World Conf. on Humanities and Social Sciences (WCHSS), 25–30. London: Francis Academic Press.
Liu, X., C. Zhang, X. Chang, W. Zhou, Y. Cheng, and Y. Duan. 2015. “Precise simulation analysis of the thermal field in mass concrete with a pipe water cooling system.” Appl. Therm. Eng. 78 (5): 449–459. https://doi.org/10.1016/j.applthermaleng.2014.12.050.
Myers, T. G., N. D. Fowkes, and Y. Ballim. 2009. “Modeling the cooling of concrete by piped water.” J. Eng. Mech. 135 (12): 1375–1383. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000046.
Nguyen, C. T., and N. A. Aniskin. 2019. “Temperature regime during the construction massive concrete with pipe cooling.” Mag. Civ. Eng. 89 (5): 156–166. https://doi.org/10.18720/MCE.89.13.
Nguyen, T.-C., T. P. Huynh, and V. L. Tang. 2019. “Prevention of crack formation in massive concrete at an early age by cooling pipe system.” Asian J. Civ. Eng. 20 (8): 1101–1107. https://doi.org/10.1007/s42107-019-00175-5.
Qiu, Y., and G. Zhang. 2017. “Stress and damage in concrete induced by pipe cooling at mesoscopic scale.” Adv. Mech. Eng. 9 (2): 1–17. https://doi.org/10.1177/1687814017690509.
Rostásy, F. S., and M. Krauß. 2003. Frühe Risse in massigen Betonbauteilen—Ingenieurmodelle für die Planung von Gegenmaßnahmen” [Early cracks in massive concrete elements—Engineering models for planning countermeasures]. [In German.] Berlin: Beton- und Stahlbetonbau, Ernst & Sohn. https://doi.org/10.1002/best.200301130.
Seruga, A., and M. Zych. 2015. “Thermal cracking of the cylindrical tank under construction. I: Case study.” J. Perform. Constr. Facil. 29 (4): 04014100. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000581.
Van Breugel, K. 1996. Betonconstructies onder Temperatuur-en Krimpvervormingen—Theorie en Praktijk. Delft, Netherlands: TU Delft.
Voigt, T. 1994. “Frosteinwirkung auf mineralische Deponieabdichtungen” Heft 47 [Impact of frost on the tightness of the mineral landfills]. [In German.] Berlin: Diss TU Braunschweig.
Zych, M. 2008. “Numerical analysis of cracking in hardening concrete of RC tank’s wall.” Tech. Trans. 20 (105): 227–249.
Zych, M. 2011. “Analysis of RC tank’s walls during early hardening period of concrete.” Ph.D. thesis, Division of Structural Engineering, Cracow Univ. of Technology.
Zych, M. 2015. “Case study of concrete mechanical properties development based on heat temperature measurements.” Cem. Lime Concr. 6: 383–392.
Zych, M. 2019. “A new model for crack control in reinforced concrete tank walls—Part I: Analytical investigation.” ACI Struct. J. 116 (3): 85–94. https://doi.org/10.14359/51713317.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Jul 28, 2020
Accepted: Dec 29, 2020
Published online: Apr 20, 2021
Published in print: Aug 1, 2021
Discussion open until: Sep 20, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.