Long-Term Performance of a Curved Box Girder Viaduct
Publication: Journal of Performance of Constructed Facilities
Volume 35, Issue 1
Abstract
Deformations due to environmental and mechanical loads in curved bridges can lead to fairly complex long-term effects. Instead of the one-dimensional longitudinal movement that occur in straight bridges, in curved bridges two-dimensional movements, i.e., longitudinal and transverse, need to be considered in the design stage and throughout the structure’s life span. Both deformations are related to the curvature and construction materials used in the bridge. Currently, both guided and nonguided bearings commonly are deployed to accommodate the movement and stresses caused by thermal movements in curved bridges. Bearings usually are oriented along the chord from the fixed piers of the bridge in current design practice. However, this traditional orientation is not compatible with bridge movements at each pier, which can induce excessive stresses in both superstructure and substructure. This study monitored and investigated a steel twin-box girder bridge. The fracture-critical bridge analyzed in this study lies on four horizontal and three vertical curves. Guided and nonguided expansion pot bearings are utilized, except on the fixed pier. Extreme temperature changes caused transverse superstructure movements and damage to the bearing guiding system. The monitoring system outfitted on the bridge recorded the temperature distributions as well as the bridge movement. The structural movement behavior due to temperature variation was studied, and the investigation of existing damage showed that both transverse and longitudinal movement were excessive and that the resultant forces transferred from superstructure to substructure were significant. The results indicate that a refined analysis always is required to account for curved bridges’ deformations in order to prevent structural damage.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request (i.e., bridge monitoring data and bridge inspection results).
Acknowledgments
The authors thank the University of Colorado Denver College of Engineering and Applied Sciences, the City and County of Denver, Lisa Wang, Samir Mizyed, Juan Montenegro, and Matthew MacLachlan for their support in this research.
References
AASHTO. 2002. American association of state highway officials. Standard specifications for highway bridges. 17th ed. Washington, DC: AASHTO.
AASHTO. 2014. American association of state highway and transportation officials (LRFD) bridge design specifications. 7th ed. Washington, DC: AASHTO.
Cao, Y., J. Yim, Y. Zhao, and M. L. Wang. 2010. “Temperature effects on cable stayed bridge using health monitoring system: A case study.” Struct. Health Monit. 10 (5): 523–537. https://doi.org/10.1177/1475921710388970.
CCD (City and County of Denver). 2016. West 8th Avenue Viaduct movement and stress study final report. Denver: City and County of Denver.
FHWA (Federal Highway Administration). 2017. “National bridge inventory.” US DOT Website. Accessed June 28, 2017. https://www.fhwa.dot.gov/bridge/nbi.cfm.
Giussani, F. 2009. “The effects of temperature variations on the long-term behavior of composite steel–concrete beams.” Eng. Struct. 31 (10): 2392–2406. https://doi.org/10.1016/j.engstruct.2009.05.014.
Kennedy, J., and M. Soliman. 1987. “Temperature distribution in composite bridges.” J. Struct. Eng. 113 (3): 475–482. https://doi.org/10.1061/(ASCE)0733-9445(1987)113:3(475).
Mizyed, S. 2015. “Structural analysis of cracked concrete piers and proposed rehabilitation using CFRP rods.” M.Sc. thesis, Dept. of Civil Engineering, Univ. of Colorado Denver.
Montenegro, J. D. 2015. “Mind the gap—8th avenue viaduct expansion joints study thesis report.” Master of Science thesis, Dept. of Civil Engineering, Univ. of Colorado at Denver.
Moorty, S., and C. W. Roeder. 1992. “Temperature-dependent bridge movements.” J. Struct. Eng. 118 (4): 1090–1105. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:4(1090).
Reynolds, J. C. 1972. “Thermal stresses and movements in bridges.” M.Sc. thesis, Dept. of Civil Engineering, Univ. of Missouri-Rolla.
Rojas, E. 2014. “Uniform temperature predictions and temperature gradient effects on I-girder and box girder concrete bridges.” M.Sc. thesis, Dept. of Civil and Environmental Engineering, Utah State Univ.
Wang, W. 2015. “Structure analysis and optimal design of curved bridge bearing considering temperature variations.” M.Sc. thesis, Dept. of Civil Engineering, Univ. of Colorado Denver.
Zhou, L., Y. Xia, J. M. W. Brownjohn, and K. Y. Koo. 2015. “Temperature analysis of a long-span suspension bridge based on field monitoring and numerical simulation.” J. Bridge Eng. 21 (1): 04015027. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000786.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Jun 15, 2020
Accepted: Aug 26, 2020
Published online: Nov 19, 2020
Published in print: Feb 1, 2021
Discussion open until: Apr 19, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.