Conception and Evaluation of a Novel Type of Support in Loess Tunnels
Publication: Journal of Performance of Constructed Facilities
Volume 35, Issue 1
Abstract
The limited efficiency of current supports has led to serious support system problems in loess tunnel construction, which are mainly noted in arch distortion, shotcrete cracking, surface subsidence, and even total structural failure. A novel type of support, called the steel-concrete composite support system (SCCS), is proposed in the present study via an in-depth analysis of support failure cases in China’s loess tunnels. Additionally, it places emphasis on the enhancement of the primary lining, which consists of three bearing layers: (1) the arch layer, (2) the reinforcing skeleton layer, and (3) the concrete packed layer. The new type of support can provide greater supporting capacity by closing the excavated space immediately after the new arch has been installed, and it can then be strengthened by grouting and the installation of molded concrete. The hyperstatic reaction method (HRM) model and three-dimensional numerical model were established using ANSYS software, and the results demonstrate that the SCCS outperformed the conventional support system in terms of both structural safety and load-bearing capacity. It was also found to achieve superior practical worthiness with flexibility and efficiency during the tunneling process, which indicates that the new support system is much more reliable for bearing more variable loads and dealing with severe deformation in loess tunnel construction.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
This study was supported by the National Natural Science Foundation of China (Grant Nos. 51978064 and 52008028) and the Fundamental Research Funds for the Central Universities, CHD (Grant Nos. 300102210112 and 300102210530).
References
Bae, G. J., H. S. Shin, C. Sicilia, Y. G. Choi, and J. J. Lim. 2005. “Homogenization framework for three-dimensional elastoplastic finite element analysis of a grouted pipe-roofing reinforcement method for tunneling.” Int. J. Numer. Anal. Methods Geomech. 29 (1): 1–24. https://doi.org/10.1002/nag.402.
Carranza-Torres, C., and C. Fairhurst. 2000. “Application of the convergence-confinement method of tunnel design to rock masses that satisfy the Hoek-Brown failure criterion.” Tunnelling Underground Space Technol. 15 (2): 187–213. https://doi.org/10.1016/S0886-7798(00)00046-8.
Chang, S. B., and S. M. Zhang. 2007. Engineering geology manual. [In Chinese.] 4th ed. Beijing: China Architecture & Building Press.
CNS (Chinese National Standard). 2018. Specifications for design of highway tunnels. JTG 3370.1-2018. Beijing: China Communications Press.
Dai, X. H., and L. Dennis. 2010. “Numerical modelling of the axial compressive behaviour of short concrete-filled elliptical steel columns.” J. Constr. Steel Res. 66 (7): 931–942. https://doi.org/10.1016/j.jcsr.2010.02.003.
Do, N. A., D. Dias, P. Oreste, and I. Djeran-Maigre. 2014. “A new numerical approach to the hyperstatic reaction method for segmental tunnel linings.” Int. J. Numer. Anal. Methods Geomech. 38 (15): 1617–1632. https://doi.org/10.1002/nag.2277.
Gong, B., Y. J. Jiang, and L. J. Chen. 2019. “Feasibility investigation of the mechanical behavior of methane hydrate-bearing specimens using the multiple failure method.” J. Nat. Gas Sci. Eng. 69 (Sep): 102915. https://doi.org/10.1016/j.jngse.2019.102915.
Gong, B., Y. J. Jiang, P. Yan, and S. H. Zhang. 2020. “Discrete element numerical simulation of mechanical properties of methane hydrate-bearing specimen considering deposit angles.” J. Nat. Gas Sci. Eng. 76 (Apr): 103182. https://doi.org/10.1016/j.jngse.2020.103182.
Han, L. H., W. Li, and R. Bjorhovde. 2014. “Developments and advanced applications of concrete-filled steel tubular (CFST) structures: Members.” J. Constr. Steel Res. 100 (Sep): 211–228. https://doi.org/10.1016/j.jcsr.2014.04.016.
Han, L. H., G. H. Yao, and Z. Tao. 2007. “Performance of concrete-filled thin-walled steel tubes under pure torsion.” Thin-Walled Struct. 45 (1): 24–36. https://doi.org/10.1016/j.tws.2007.01.008.
Hill, R. 1963. “Elastic properties of reinforced solids: Some theoretical principles.” J. Mech. Phys. Solids 11 (5): 357–372. https://doi.org/10.1016/0022-5096(63)90036-X.
Huang, C. S., Y. K. Yeh, G. Y. Liu, H. T. Hu, K. C. Tsai, Y. T. Weng, S. H. Wang, and M. H. Wu. 2002. “Axial load behavior of stiffened concrete-filled steel columns.” J. Struct. Eng. 128 (9): 1222–1230. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:9(1222).
Huang, W. P., Q. Yuan, Y. L. Tan, J. Wang, G. L. Liu, G. L. Qu, and C. Li. 2018. “An innovative support technology employing a concrete-filled steel tubular structure for a 1000-m-deep roadway in a high in situ stress field.” Tunnelling Underground Space Technol. 73 (Mar): 26–36. https://doi.org/10.1016/j.tust.2017.11.007.
Jiang, M., J. Sima, Y. Cui, H. Hu, C. Zhou, and H. Lei. 2017. “Experimental investigation of the deformation characteristics of natural loess under the stress paths in shield tunnel excavation.” Int. J. Geomech. 17 (9): 04017079. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000972.
Jiang, M. J., F. G. Zhang, H. J. Hu, Y. J. Cui, and J. B. Peng. 2014. “Structural characterization of natural loess and remolded loess under triaxial tests.” Eng. Geol. 181 (Oct): 249–260. https://doi.org/10.1016/j.enggeo.2014.07.021.
Kang, H. P., J. Lin, and M. J. Fan. 2015. “Investigation on support pattern of a coal mine roadway within soft rocks-a case study.” Int. J. Coal Geol. 140 (Feb): 31–40. https://doi.org/10.1016/j.coal.2015.01.003.
Kroetz, H. M., N. A. Do, D. Dias, and A. T. Beck. 2018. “Reliability of tunnel lining design using the hyperstatic reaction method.” Tunnelling Underground Space Technol. 77 (Jul): 59–67. https://doi.org/10.1016/j.tust.2018.03.028.
Lai, H. P., W. L. Song, Y. Y. Liu, and R. Chen. 2017. “Influence of flooded loessial overburden on the tunnel lining: Case study.” J. Perform. Constr. Facil. 31 (6): 04017108. https://doi.org/10.1061/(ASCE)CF.1943-5509.0001100.
Li, C. C. 2017. “Principles of rockbolting design.” J. Rock Mech. Geotech. Eng. 9 (3): 396–414. https://doi.org/10.1016/j.jrmge.2017.04.002.
Li, H., E. L. Ma, J. X. Lai, L. X. Wang, S. S. Xu, K. Wang, and T. Liu. 2020. “Tunnelling induced settlement and treatment techniques for a loess metro in Xi’an.” Adv. Civ. Eng. 2020 (Nov): 1854813. https://doi.org/10.1155/2020/1854813.
Li, J., S. J. Shao, and S. Shao. 2019. “Collapsible characteristics of loess tunnel site and their effects on tunnel structure.” Tunnelling Underground Space Technol. 83 (Jan): 509–519. https://doi.org/10.1016/j.tust.2018.08.035.
Li, P., T. Li, and S. K. Vanapalli. 2016a. “Influence of environmental factors on the wetting front depth: A case study in the loess plateau.” Eng. Geol. 214 (Nov): 1–10. https://doi.org/10.1016/j.enggeo.2016.09.008.
Li, P. F., and Y. Zhao. 2016. “Performance of a multi-face tunnel excavated in loess ground based on field monitoring and numerical modeling.” Arabian J. Geosci. 9 (14): 640–650. https://doi.org/10.1007/s12517-016-2668-3.
Li, P. F., Y. Zhao, and X. J. Zhou. 2016b. “Displacement characteristics of high-speed railway tunnel construction in loess ground by using multi-step excavation method.” Tunnelling Underground Space Technol. 51 (Jan): 41–55. https://doi.org/10.1016/j.tust.2015.10.009.
Li, S. C., W. Lu, Q. Wang, H. B. Sun, B. Jiang, and Q. Qin. 2018a. “Study on failure mechanism and mechanical properties of casing joints of square steel confined concrete arch.” Eng. Fail. Anal. 92 (Oct): 539–552. https://doi.org/10.1016/j.engfailanal.2018.05.011.
Li, W. T., N. Yang, Y. C. Mei, Y. H. Zhang, L. Wang, and H. Y. Ma. 2020. “Experimental investigation of the compression-bending property of the casing joints in a concrete filled steel tubular supporting arch for tunnel engineering.” Tunnelling Underground Space Technol. 96 (Feb): 103184. https://doi.org/10.1016/j.tust.2019.103184.
Li, W. T., N. Yang, B. Yang, H. Y. Ma, T. C. Li, Q. Wang, G. Wang, Y. T. Du, and M. X. Zhao. 2018b. “An improved numerical simulation approach for arch-bolt supported tunnels with large deformation.” Tunnelling Underground Space Technol. 77 (Jul): 1–12. https://doi.org/10.1016/j.tust.2018.03.001.
Li, Y. Y., H. J. Ling, and Z. L. Li. Forthcoming. “Comparison of durability and mechanism between sprayed concrete and ordinary concrete at different erosion age.” J. Mater. Civ. Eng. 33 (1).
Liu, T., Y. Xie, Z. H. Feng, Y. B. Luo, K. Wang, and W. Xu. 2020. “Better understanding the failure modes of tunnels excavated in the boulder-cobble mixed strata by distinct element method.” Eng. Fail. Anal. 116 (Oct): 104712. https://doi.org/10.1016/j.engfailanal.2020.104712.
Liu, Y., and H. Lai. 2019. “Load characteristics of tunnel lining in flooded loess strata considering loess structure.” Adv. Civ. Eng. 2019 (Sep): 3731965. https://doi.org/10.1155/2019/3731965.
Liu, Y. Y., H. P. Lai, Y. L. Xie, and W. L. Song. 2017. “Cracks analysis of highway tunnel lining in flooded loess.” Proc. Inst. Civil Eng. Geotech. E. 170 (1): 62–72. https://doi.org/10.1680/jgeen.15.00177.
Luo, Y. B., J. X. Chen, S. T. Gao, X. H. Deng, and P. S. Diao. 2017. “Stability analysis of super-large-section tunnel in loess ground considering water infiltration caused by irrigation.” Environ. Earth Sci. 76 (22): 763–780. https://doi.org/10.1007/s12665-017-7106-7.
Ma, E. L., J. X. Lai, L. X. Wang, K. Wang, S. S. Xu, C. J. Li, and C. X. Guo. 2021. “Review of cutting-edge sensing technologies for urban underground construction.” Measurement 167 (Jan): 108289. https://doi.org/10.1016/j.measurement.2020.108289.
Massone, L. M., and F. Nazar. 2018. “Analytical and experimental evaluation of the use of fibers as partial reinforcement in shotcrete for tunnels in Chile.” Tunnelling Underground Space Technol. 77 (Jul): 13–25. https://doi.org/10.1016/j.tust.2018.03.027.
Oke, J., N. Vlachopoulos, and M. Diederichs. 2016. “Semi-analytical model for umbrella arch systems employed in squeezing ground conditions.” Tunnelling Underground Space Technol. 56 (Jun): 136–156. https://doi.org/10.1016/j.tust.2016.03.006.
Oke, J., N. Vlachopoulos, and M. Diederichs. 2018. “Improvement to the convergence-confinement method: Inclusion of support installation proximity and stiffness.” Rock Mech. Rock Eng. 51 (5): 1495–1519. https://doi.org/10.1007/s00603-018-1418-0.
Oreste, P. P. 2003. “Analysis of structural interaction in tunnels using the covergence–confinement approach.” Tunnelling Underground Space Technol. 18 (4): 347–363. https://doi.org/10.1016/S0886-7798(03)00004-X.
Oreste, P. P. 2007. “A numerical approach to the hyperstatic reaction method for the dimensioning of tunnel supports.” Tunnelling Underground Space Technol. 22 (2): 185–205. https://doi.org/10.1016/j.tust.2006.05.002.
Qiu, J. L., Y. W. Qin, J. X. Lai, F. Y. Liu, L. X. Wang, and Y. B. Luo. Forthcoming. “Seepage characteristics in loess strata subjected to single point water supply.” J. Hydrol.
Qiu, J. L., Y. W. Qin, J. X. Lai, K. Wang, F. Y. Niu, H. Wang, and G. L. Zhang. 2019. “Structural response of the metro tunnel under local dynamic water environment in loess strata.” Geofluids 2019 (Jan): 8541959. https://doi.org/10.1155/2019/8541959.
Qiu, J. L., Y. L. Xie, H. B. Fan, Z. C. Wang, and Y. W. Zhang. 2017. “Centrifuge modelling of twin-tunnelling induced ground movements in loess strata.” Arabian J. Geosci. 10 (22): 493–503. https://doi.org/10.1007/s12517-017-3297-1.
Sharifzadeh, M., R. Daraei, and M. S. Broojerdi. 2012. “Design of sequential excavation tunneling in weak rocks through findings obtained from displacements based back analysis.” Tunnelling Underground Space Technol. 28 (1): 10–17. https://doi.org/10.1016/j.tust.2011.08.003.
Sharifzadeh, M., F. Kolivand, M. Ghorbani, and S. Yasrobi. 2013. “Design of sequential excavation method for large span urban tunnels in soft ground-Niayesh tunnel.” Tunnelling Underground Space Technol. 35 (Apr): 178–188. https://doi.org/10.1016/j.tust.2013.01.002.
Soranzo, E., R. Tamagnini, and W. Wu. 2015. “Face stability of shallow tunnels in partially saturated soil: Centrifuge testing and numerical analysis.” Géotechnique 65 (6): 454–467. https://doi.org/10.1680/geot.14.P.123.
Tao, Z., Z. B. Wang, and Q. Yu. 2013. “Finite element modelling of concrete-filled steel stub columns under axial compression.” J. Constr. Steel Res. 89 (Oct): 121–131. https://doi.org/10.1016/j.jcsr.2013.07.001.
Wang, Q., B. Jiang, Y. Li, X. Shao, F. Q. Wang, S. C. Li, S. G. Zhang, and G. Q. Ruan. 2017. “Mechanical behaviors analysis on a square-steel-confined-concrete arch centering and its engineering application in a mining project.” Eur. J. Environ. Civ. Eng. 21 (4): 389–411. https://doi.org/10.1080/19648189.2015.1124809.
Wang, X. L., J. X. Lai, S. Y. He, R. S. Garnes, and Y. Zhang. 2020. “Karst geology and mitigation measures for hazards during metro system construction in Wuhan, China.” Nat. Hazards 103 (3): 2905–2927. https://doi.org/10.1007/s11069-020-04108-3.
Wang, Z. C. 2019. “Analysis on characteristics of composite structure support system in loess tunnel.” [In Chinese.] Ph.D. thesis, Highway School, Chang’an Univ.
Wang, Z. C., Y. Xie, J. X. Lai, Y. L. Xie, and C. X. Guo. Forthcoming. “Designing an innovative support system in loess tunnel.” Geomech. Eng.
Wang, Z. C., Y. L. Xie, H. Q. Liu, and Z. H. Feng. 2019. “Analysis on deformation and structural safety of a novel concrete-filled steel tube support system in loess tunnel.” Eur. J. Environ. Civ. Eng. 2019 (Feb): 1–21. https://doi.org/10.1080/19648189.2018.1515665.
Weng, X. L., Y. F. Sun, Y. W. Zhang, H. S. Niu, X. Liu, and Y. L. Dong. 2019. “Physical modeling of wetting-induced collapse of shield tunneling in loess strata.” Tunnelling Underground Space Technol. 90 (Aug): 208–219. https://doi.org/10.1016/j.tust.2019.05.004.
Wong, L. N. Y., Q. Fang, and D. L. Zhang. 2013. “Mechanical analysis of circular tunnels supported by steel sets embedded in primary linings.” Tunnelling Underground Space Technol. 37 (Aug): 80–88. https://doi.org/10.1016/j.tust.2013.03.011.
Wu, K., and Z. S. Shao. 2018. “Effects of pipe roof support and grouting pre-reinforcement on the track settlement.” Adv. Civ. Eng. 2018 (Jan): 6041305. https://doi.org/10.1155/2018/6041305.
Xiao, J. Z., F. C. Dai, Y. Q. Wei, and Y. C. Xing. 2016. “Comparative analysis of excavation schemes for a tunnel constructed through loose deposits.” J. Perform. Constr. Facil. 30 (4): 04015061. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000813.
Xu, F., S. C. Li, Q. Q. Zhang, L. P. Li, S. S. Shi, and Q. Zhang. 2017. “A new type support structure introduction and its contrast study with traditional support structure used in tunnel construction.” Tunnelling Underground Space Technol. 63 (Mar): 171–182. https://doi.org/10.1016/j.tust.2016.11.012.
Xue, Y. G., X. L. Zhang, S. C. Li, D. H. Qiu, M. X. Su, L. P. Li, Z. Q. Li, and Y. F. Tao. 2018. “Analysis of factors influencing tunnel deformation in loess deposits by data mining: A deformation prediction model.” Eng. Geol. 232 (Jan): 94–103. https://doi.org/10.1016/j.enggeo.2017.11.014.
Yan, Q., S. C. Li, C. Xie, and Y. Li. 2018. “Analytical solution for bolted tunnels in expansive loess using the convergence-confinement method.” Int. J. Geomech. 18 (1): 04017124. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000989.
Yang, X. 2008. “The K-zero consolidation characteristic and method research on the unsaturated undisturbed loess.” [In Chinese.] Master thesis, Highway School, Chang’an Univ.
Yates, K., C. H. Fenton, and D. H. Bell. 2018. “A review of the geotechnical characteristics of loess and loess-derived soils from Canterbury, South Island, New Zealand.” Eng. Geol. 236 (Mar): 11–21. https://doi.org/10.1016/j.enggeo.2017.08.001.
Zhang, W. J., W. T. Li, N. Yang, Q. Wang, T. C. Li, and G. Wang. 2017. “Determination of the bearing capacity of a concrete-filled steel tubular arch support for tunnel engineering: Experimental and theoretical studies.” KSCE J. Civ. Eng. 21 (7): 2932–2945. https://doi.org/10.1007/s12205-017-1418-8.
Zhang, Y., Z. Q. Hu, L. Li, and Z. J. Xue. 2018. “Improving the structure and mechanical properties of loess by acid solutions—An experimental study.” Eng. Geol. 244 (Oct): 132–145. https://doi.org/10.1016/j.enggeo.2018.07.023.
Zhang, Y. X., J. S. Yang, and F. Yang. 2015. “Field investigation and numerical analysis of landslide induced by tunneling.” Eng. Fail. Anal. 47 (Jan): 25–33. https://doi.org/10.1016/j.engfailanal.2014.09.011.
Zhao, Y., H. W. He, and P. F. Li. 2018. “Key techniques for the construction of high-speed railway large-section loess tunnels.” Engineering 4 (2): 254–259. https://doi.org/10.1016/j.eng.2017.07.003.
Zhao, Y., P. F. Li, and S. M. Tian. 2013. “Prevention and treatment technologies of railway tunnel water inrush and mud gushing in China.” J. Rock Mech. Geotech. Eng. 5 (6): 468–477. https://doi.org/10.1016/j.jrmge.2013.07.009.
Zhou, Z. J., Z. P. Zhang, and C. R. Chen. Forthcoming. “Application of load transfer method for bored pile in loess area.” Eur. J. Environ. Civ. Eng. 24 (12).
Information & Authors
Information
Published In
Journal of Performance of Constructed Facilities
Volume 35 • Issue 1 • February 2021
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Sep 17, 2019
Accepted: Jul 13, 2020
Published online: Dec 9, 2020
Published in print: Feb 1, 2021
Discussion open until: May 9, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.