Assessment of the Internal Shaft Friction of Tubular Piles in Jointed Weak Rock Using the Discrete-Element Method
Publication: Journal of Performance of Constructed Facilities
Volume 33, Issue 6
Abstract
This study focuses on the internal shaft friction of open-ended tubular piles induced by jointed weak rock plugs. To investigate the bearing mechanism of the plug, push-up load tests were carried out on the jointed mudstone inside a tubular pile. The discrete-element method (DEM) was used in order to consider heterogeneity and to reproduce the discrete nature of the rock mass. A flat-joint model was used to reproduce the mechanical behavior of mudstone, and a smooth-joint contact model was used to replicate natural joints. The push-up load tests were carried out using the calibrated properties of a weak mudstone. The effects of joint density and joint dip were examined in detail and, as expected, the push-up force of the rock plug was influenced by the joint properties because joint density and joint dip had to some extent affected the plug resistance. The existing joints reduced the push-up force when the joints were steep, whereas the horizontal joints had a minimal effect on altering the inner shaft friction compared with the intact rock mass. The reduced friction along the pile was amplified with joint density, while the exponential increase of vertical stress from the top of the rock plug to the bottom revealed that the inner shaft resistance was mainly mobilized at the bottom portion of the rock plug. The findings of this study increase our understanding of joint dip and joint density affecting the internal shaft resistance of open-ended tubular piles; this knowledge can be used further to develop a design methodology for open-ended tubular piles in weak rock while assessing plugging effects.
Get full access to this article
View all available purchase options and get full access to this article.
References
Bahaaddini, M., G. Sharrock, and B. Hebblewhite. 2013. “Numerical investigation of the effect of joint geometrical parameters on the mechanical properties of a non-persistent jointed rock mass under uniaxial compression.” Comput. Geotech. 49 (1): 206–225. https://doi.org/10.1016/j.compgeo.2012.10.012.
Bahrani, N., and P. K. Kaiser. 2016. “Numerical investigation of the influence of specimen size on the unconfined strength of defected rocks.” Comput. Geotech. 77 (1): 56–67. https://doi.org/10.1016/j.compgeo.2016.04.004.
Bahrani, N., P. K. Kaiser, and B. Valley. 2014. “Distinct element method simulation of an analogue for a highly interlocked, non-persistently jointed rockmass.” Int. J. Rock Mech. Min. Sci. 71 (1): 117–130. https://doi.org/10.1016/j.ijrmms.2014.07.005.
Bandis, S. 1980. “Experimental studies of scale effects on shear strength, and deformation of rock joints.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Leeds.
Bažant, Z. P., B. Shang-Ping, and G. Ravindra. 1993. “Fracture of rock: Effect of loading rate.” Eng. Fract. Mech. 45 (3): 393–398. https://doi.org/10.1016/0013-7944(93)90024-M.
Broos, E., R. Sibbes, and J. de Gijt. 2017. “Widening a harbor basin, demolition of a deep see quay wall in Rotterdam.” In Proc., COME2017: Decommissioning of Offshore Geotechnical Structures, 251–262. Hamburg, Germany: Institute of Geotechnical Engineering and Construction Management, Hamburg Univ. of Technology.
Brown, D. A., and W. R. Thompson III. 2015. Design and load testing of large diameter open-ended driven piles. Washington, DC: National Academies Press.
Chiu, C. C., T. T. Wang, M. C. Weng, and T. H. Huang. 2013. “Modeling the anisotropic behavior of jointed rock mass using a modified smooth-joint model.” Int. J. Rock Mech. Min. Sci. 62 (1): 14–22. https://doi.org/10.1016/j.ijrmms.2013.03.011.
Cho, N. A., C. Martin, and D. Sego. 2007. “A clumped particle model for rock.” Int. J. Rock Mech. Min. Sci. 44 (7): 997–1010. https://doi.org/10.1016/j.ijrmms.2007.02.002.
Cundall, P. A., and O. D. Strack. 1979. “A discrete numerical model for granular assemblies.” Géotechnique 29 (1): 47–65. https://doi.org/10.1680/geot.1979.29.1.47.
De Nicola, A., and M. Randolph. 1997. “The plugging behaviour of driven and jacked piles in sand.” Géotechnique 47 (4): 841–856. https://doi.org/10.1680/geot.1997.47.4.841.
Ding, X., and L. Zhang. 2014. “A new contact model to improve the simulated ratio of unconfined compressive strength to tensile strength in bonded particle models.” Int. J. Rock Mech. Min. Sci. 69 (1): 111–119. https://doi.org/10.1016/j.ijrmms.2014.03.008.
Ding, X., L. Zhang, H. Zhu, and Q. Zhang. 2014. “Effect of model scale and particle size distribution on PFC3D simulation results.” Rock Mech. Rock Eng. 47 (6): 2139–2156. https://doi.org/10.1007/s00603-013-0533-1.
Dong, Y., B. Fatahi, H. Khabbaz, and H. Zhang. 2018. “Influence of particle contact models on soil response of poorly graded sand during cavity expansion in discrete-element simulation.” J. Rock Mech. Geotech. Eng. 10 (6): 1154–1170. https://doi.org/10.1016/j.jrmge.2018.03.009..
Engineering Heritage Western Australia. 2014. Nomination of Stirling Bridge for an Engineering Heritage Australia heritage recognition award. Hamilton Hill, Australia: Engineering Heritage Western Australia.
Fatahi, B., S. Basack, P. Ryan, W.-H. Zhou, and H. Khabbaz. 2014. “Performance of laterally loaded piles considering soil and interface parameters.” Geomech. Eng. 7 (5): 495–524. https://doi.org/10.12989/gae.2014.7.5.495.
Fattah, M. Y., and W. H. Al-Soudani. 2016. “Bearing capacity of open-ended pipe piles with restricted soil plug.” Ships Offshore Struct. 11 (5): 501–516. https://doi.org/10.1080/17445302.2015.1030247.
Gaffney, E. 1976. Measurements of dynamic friction between rock and steel. Washington, DC: Defense Nuclear Agency.
Ghazvinian, A., V. Sarfarazi, W. Schubert, and M. Blumel. 2012. “A study of the failure mechanism of planar non-persistent open joints using PFC2D.” Rock Mech. Rock Eng. 45 (5): 677–693. https://doi.org/10.1007/s00603-012-0233-2.
Gudavalli, S., O. Safaqah, and H. Seo. 2013. “Effect of soil plugging on axial capacity of open-ended pipe piles in sands.” In Proc., 18th Int. Conf. on Soil Mechanics and Geotechnical Engineering, 1487–1490. Paris: Presses des Ponts.
Guo, Y., and X. B. Yu. 2016. “Design and analyses of open-ended pipe piles in cohesionless soils.” Front. Struct. Civ. Eng. 10 (1): 22–29. https://doi.org/10.1007/s11709-016-0314-5.
Hayano, K., T. Sato, and F. Tatsuoka. 1997. “Deformation characteristics of a sedimentary soft mudstone from triaxial compression tests using rectangular prism specimens.” Géotechnique 47 (3): 439–449. https://doi.org/10.1680/geot.1997.47.3.439.
Hazzard, J. F., R. P. Young, and S. Maxwell. 2000. “Micromechanical modeling of cracking and failure in brittle rocks.” J. Geophys. Res. 105 (B7): 16683–16697. https://doi.org/10.1029/2000JB900085.
Huang, D., J. Wang, and S. Liu. 2015. “A comprehensive study on the smooth joint model in DEM simulation of jointed rock masses.” Granular Matter 17 (6): 775–791. https://doi.org/10.1007/s10035-015-0594-9.
Hussein, M. H., and G. G. Goble. 2000. “Structural failure of pile foundations during installation.” In Construction Congress VI: Building Together for a Better Tomorrow in an Increasingly Complex World, 799–807. Reston, VA: ASCE.
Itasca. 2015. “PFC-particle flow code in 2 and 3 dimension.” In Documentation set of version 5.00.21. Minneapolis: Itasca Consulting Group.
Ivars, D. M., M. Pierce, D. DeGagné, and C. Darcel. 2008. “Anisotropy and scale dependency in jointed rock-mass strength—A synthetic rock mass study.” In Proc., 1st Int. FLAC/DEM Symp. on Numerical Modeling, 231–239. Minneapolis: Itasca Consulting Group, Inc.
Ivars, D. M., M. E. Pierce, C. Darcel, J. Reyes-Montes, D. O. Potyondy, R. P. Young, and P. A. Cundall. 2011. “The synthetic rock mass approach for jointed rock mass modelling.” Int. J. Rock Mech. Min. Sci. 48 (2): 219–244. https://doi.org/10.1016/j.ijrmms.2010.11.014.
Jardine, R., F. Chow, R. Overy, and J. Standing. 2005. ICP design methods for driven piles in sands and clays. London: Thomas Telford Publishing.
Jardine, R., J. Standing, and F. Chow. 2006. “Some observations of the effects of time on the capacity of piles driven in sand.” Géotechnique 56 (4): 227–244. https://doi.org/10.1680/geot.2006.56.4.227.
Jeong, S., J. Ko, J. Won, and K. Lee. 2015. “Bearing capacity analysis of open-ended piles considering the degree of soil plugging.” Soils Found. 55 (5): 1001–1014. https://doi.org/10.1016/j.sandf.2015.06.007.
Jing, L. 2003. “A review of techniques, advances and outstanding issues in numerical modelling for rock mechanics and rock engineering.” Int. J. Rock Mech. Min. Sci. 40 (3): 283–353. https://doi.org/10.1016/S1365-1609(03)00013-3.
Ko, J., and S. Jeong. 2014. “Plugging effect of open-ended piles in sandy soil.” Can. Geotech. J. 52 (5): 535–547. https://doi.org/10.1139/cgj-2014-0041.
Ko, J., S. Jeong, and J. K. Lee. 2016. “Large deformation FE analysis of driven steel pipe piles with soil plugging.” Comput. Geotech. 71 (1): 82–97. https://doi.org/10.1016/j.compgeo.2015.08.005.
Kumara, J. J., Y. Kikuchi, and T. Kurashina. 2016. “Effects of the lateral stress on the inner frictional resistance of pipe piles driven into sand.” Int. J. Geo-Eng. 7 (1): 1–14. https://doi.org/10.1186/s40703-016-0015-x.
Lehane, B., and M. F. Randolph. 2002. “Evaluation of a minimum base resistance for driven pipe piles in siliceous sand.” J. Geotech. Geoenviron. Eng. 128 (3): 198–205. https://doi.org/10.1061/(ASCE)1090-0241(2002)128:3(198).
Lin, C., C. Bennett, J. Han, and R. Parsons. 2014. “Effect of soil stress history on scour evaluation of pile-supported bridges.” J. Perform. Constr. Facil. 29 (6): 1–11. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000681.
Liu, X., W. Zhu, Q. Yu, S. Chen, and R. Li. 2017. “Estimation of the joint roughness coefficient of rock joints by consideration of two-order asperity and its application in double-joint shear tests.” Eng. Geol. 220 (1): 243–255. https://doi.org/10.1016/j.enggeo.2017.02.012.
Long, M. 1995. “The behaviour of driven tubular steel piles in the laminated mudstones of south-west Ireland.” Proc. Inst. Civ. Eng. Geotech. Eng. 113 (4): 242–252. https://doi.org/10.1680/igeng.1995.28020.
Matsumoto, T., P. Kitiyodom, and T. Shintani. 2007. “Trend of research and practice of pile foundations in Japan.” In Proc., Int. Workshop on Recent Advances in Deep Foundations, 143–173. Yokosuka, Japan: Port and Airport Research Institute.
Matsumoto, T., Y. Michi, and T. Hirano. 1995. “Performance of axially loaded steel pipe piles driven in soft rock.” J. Geotech. Eng. 121 (4): 305–315. https://doi.org/10.1061/(ASCE)0733-9410(1995)121:4(305).
Mostafa, Y. E. 2011. “Onshore and offshore pile installation in dense soils.” J. Am. Sci. 7 (7): 549–563.
Nguyen, L., and B. Fatahi. 2016. “Behaviour of clay treated with cement & fibre while capturing cementation degradation and fibre failure–C3F Model.” Int. J. Plast. 81 (1): 168–195. https://doi.org/10.1016/j.ijplas.2016.01.015.
Nguyen, L., B. Fatahi, and H. Khabbaz. 2017. “Development of a constitutive model to predict the behavior of cement-treated clay during cementation degradation: C3 model.” Int. J. Geomech. 17 (7): 04017010. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000863.
Oda, M. 1977. “Co-ordination number and its relation to shear strength of granular material.” Soils Found. 17 (2): 29–42. https://doi.org/10.3208/sandf1972.17.2_29.
Olsson, W. 1991. “The compressive strength of tuff as a function of strain rate from 10− 6 to 103/sec.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 28 (1): 115–118. https://doi.org/10.1016/0148-9062(91)93241-W.
Paik, K., R. Salgado, J. Lee, and B. Kim. 2003. “Behavior of open-and closed-ended piles driven into sands.” J. Geotech. Geoenviron. Eng. 129 (4): 296–306. https://doi.org/10.1061/(ASCE)1090-0241(2003)129:4(296).
Park, B., and K.-B. Min. 2015. “Bonded-particle discrete-element modeling of mechanical behavior of transversely isotropic rock.” Int. J. Rock Mech. Min. Sci. 76 (1): 243–255. https://doi.org/10.1016/j.ijrmms.2015.03.014.
Park, J. W., and J. J. Song. 2009. “Numerical simulation of a direct shear test on a rock joint using a bonded-particle model.” Int. J. Rock Mech. Min. Sci. 46 (8): 1315–1328. https://doi.org/10.1016/j.ijrmms.2009.03.007.
Poon, B., G. McKay, K. Chan, and L. R. Castañeda. 2017. Dynamic load testing of 2 meter steel tubular piles driven into foliated phyllite bedrock. Melbourne: Deep Foundation Institute.
Potyondy, D. 2012. “A flat-jointed bonded-particle material for hard rock.” In 46th US Rock Mechanics/Geomechanics Symp. Chicago: American Rock Mechanics Association.
Potyondy, D. 2013. PFC3D flat joint contact model version 1. Minneapolis: Itasca Consulting Group.
Potyondy, D., and P. Cundall. 2004. “A bonded-particle model for rock.” Int. J. Rock Mech. Min. Sci. 41 (8): 1329–1364. https://doi.org/10.1016/j.ijrmms.2004.09.011.
Potyondy, D. O. 2007. Smooth-joint model version 2 (for PFC2D/3D manual). Minneapolis: Itasca Consulting Group.
Potyondy, D. O. 2015. “The bonded-particle model as a tool for rock mechanics research and application: Current trends and future directions.” Geosystem. Eng. 18 (1): 1–28. https://doi.org/10.1080/12269328.2014.998346.
Randolph, M. 2018. “Potential damage to steel pipe piles during installation.” IPA Newsl. 3 (1): 3–10.
Randolph, M., E. Leong, and G. Houlsby. 1991. “One-dimensional analysis of soil plugs in pipe piles.” Géotechnique 41 (4): 587–598. https://doi.org/10.1680/geot.1991.41.4.587.
Randolph, M., M. May, E. Leong, A. Hyden, and J. Murff. 1992. “Soil plug response in open-ended pipe piles.” J. Geotech. Eng. 118 (5): 743–759. https://doi.org/10.1061/(ASCE)0733-9410(1992)118:5(743).
Schöpfer, M. P., S. Abe, C. Childs, and J. J. Walsh. 2009. “The impact of porosity and crack density on the elasticity, strength and friction of cohesive granular materials: Insights from DEM modelling.” Int. J. Rock Mech. Min. Sci. 46 (2): 250–261. https://doi.org/10.1016/j.ijrmms.2008.03.009.
Thongmunee, S., T. Matsumoto, S.-I. Kobayashi, P. Kitiyodom, and K. Kurosawa. 2011. “Experimental and numerical studies on push-up load tests for sand plugs in a steel pipe pile.” Soils Found. 51 (5): 959–974. https://doi.org/10.3208/sandf.51.959.
Tomlinson, M., and J. Woodward. 2008. Pile design and construction practice. 5th Ed. London: CRC Press.
Wu, S., and X. Xu. 2016. “A study of three intrinsic problems of the classic discrete-element method using flat-joint model.” Rock Mech. Rock Eng. 49 (5): 1813–1830. https://doi.org/10.1007/s00603-015-0890-z.
Xu, X., S. Wu, Y. Gao, and M. Xu. 2016. “Effects of micro-structure and micro-parameters on Brazilian tensile strength using flat-joint model.” Rock Mech. Rock Eng. 49 (9): 3575–3595. https://doi.org/10.1007/s00603-016-1021-1.
Yu, F., and J. Yang. 2011. “Improved evaluation of interface friction on steel pipe pile in sand.” J. Perform. Constr. Facil. 26 (2): 170–179. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000256.
Yu, F., and J. Yang. 2012. “Base capacity of open-ended steel pipe piles in sand.” J. Geotech. Geoenviron. Eng. 138 (9): 1116–1128. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000667.
Zhang, H. 2017. “Case histories of large diameter driven steel tubular piles on the east coast of Australia.” In Proc., 1st Int. Conf. on Geomechanics and Geoenvironmental Engineering. Sydney, Australia: IQPC.
Zhang, H., P. Hewitt, G. Yip, and K. Lin. 2013. “Aspects of driven piles on Macleay River and floodplain bridge.” In Proc., Piling & Deep Foundations 2013. Sydney: IQPC.
Zhang, L. 2010. “Prediction of end-bearing capacity of rock-socketed shafts considering rock quality designation (RQD).” Can. Geotech. J. 47 (10): 1071–1084. https://doi.org/10.1139/T10-016.
Zhang, M. S., W. H. Zhou, K. V. Yuen, and S. H. Wang. 2011. “Progressive failure and collapse of jointed rock mass using discrete-element method.” In Proc., 14th Asian Regional Conf. on Soil Mechanics and Geotechnical Engineering. Hong Kong.
Zhang, X.-P., and L. N. Y. Wong. 2013. “Loading rate effects on cracking behavior of flaw-contained specimens under uniaxial compression.” Int. J. Fract. 180 (1): 93–110. https://doi.org/10.1007/s10704-012-9803-2.
Zhang, X.-P., and L. N. Y. Wong. 2014. “Choosing a proper loading rate for bonded-particle model of intact rock.” Int. J. Fract. 189 (2): 163–179. https://doi.org/10.1007/s10704-014-9968-y.
Zhang, Y., and D. Stead. 2014. “Modelling 3D crack propagation in hard rock pillars using a synthetic rock mass approach.” Int. J. Rock Mech. Min. Sci. 72 (1): 199–213. https://doi.org/10.1016/j.ijrmms.2014.09.014.
Information & Authors
Information
Published In
Journal of Performance of Constructed Facilities
Volume 33 • Issue 6 • December 2019
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jul 13, 2018
Accepted: Mar 21, 2019
Published online: Sep 11, 2019
Published in print: Dec 1, 2019
Discussion open until: Feb 11, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.