Postfire Damage Assessment of a RC Factory Building
Publication: Journal of Performance of Constructed Facilities
Volume 33, Issue 5
Abstract
This paper presents an assessment of postfire damage of a RC factory building. The fire was limited to the ground floor; thus, the structural elements on the ground floor were fire damaged. Also, some relative displacements were observed at the expansion joints, and long wall cracks were observed on other stories. During the visual assessment, typical fire damage was observed (e.g., spalling, netlike cracks, crumbled plaster, bared or visible reinforcement, and crumbled aggregates). Also, some explosive and thermal expansion–induced damage was observed in and out of the fire-damaged areas. To evaluate the effects of the fire on the concrete, spectrophotometer and compressive strength tests were performed on concrete specimens taken from the building. It is concluded that elevated temperatures due to a fire can cause damage in the fire region, and that it can affect the overall stability of the structure.
Get full access to this article
View all available purchase options and get full access to this article.
References
ACI (American Concrete Institute). 1994. Guide for determining the fire endurance of concrete elements. ACI 216. Farmington Hills, MI: ACI.
Ali, F., A. Nadjai, and A. Abu-Tair. 2011. “Explosive spalling of normal strength concrete slabs subjected to severe fire.” Mater. Struct. 44 (5): 943–956. https://doi.org/10.1617/s11527-010-9678-5.
Ali, F. A., D. O’Connor, and A. Abu-Tair. 2001. “Explosive spalling of high-strength concrete columns in fire.” Mag. Concr. Res. 53 (3): 197–204. https://doi.org/10.1680/macr.2001.53.3.197.
Allam, S. M., H. M. F. Elbakry, and A. G. Rabeia. 2013. “Behavior of one-way reinforced concrete slabs subjected to fire.” Alexandria Eng. J. 52 (4): 749–761. https://doi.org/10.1016/j.aej.2013.09.004.
ASTM. 2016. Standard test methods for fire tests of building construction and materials. ASTM E119. West Conshohocken, PA: ASTM.
Bailey, C. 2002. “Holistic behaviour of concrete buildings in fire.” Proc. ICE Struct. Build. 152 (3): 199–212. https://doi.org/10.1680/stbu.2002.152.3.199.
Bamonte, P., and F. Lo Monte. 2015. “Reinforced concrete columns exposed to standard fire: Comparison among different constitutive models for concrete at high temperature.” Fire Saf. J. 71: 310–323. https://doi.org/10.1016/j.firesaf.2014.11.014.
Bratina, S., M. Saje, and I. Planinc. 2007. “The effects of different strain contributions on the response of RC beams in fire.” Eng. Struct. 29 (3): 418–430. https://doi.org/10.1016/j.engstruct.2006.05.008.
CEN (European Committee for Standardization). 2002. Eurocode 1: Actions on structures. Part 1-2: General actions—Actions on structures exposed to fire. EN 1991-1-2. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2004. Eurocode 2: Design of concrete structures. Part 1-2: General rules—Structural fire design. EN 1992-1-2. Brussels, Belgium: CEN.
Chan, S. Y. N., X. Luo, and W. Sun. 2000. “Effect of high temperature and cooling regimes on the compressive strength and pore properties of high performance concrete.” Constr. Build. Mater. 14 (5): 261–266. https://doi.org/10.1016/S0950-0618(00)00031-3.
Chiang, C. H., and C. L. Tsai. 2003. “Time-temperature analysis of bond strength of a rebar after fire exposure.” Cem. Concr. Res. 33 (10): 1651–1654. https://doi.org/10.1016/S0008-8846(03)00139-X.
Cooke, G. M. E. 2001. “Behaviour of precast concrete floor slabs exposed to standardized fires.” Fire Saf. J. 36 (5): 459–475. https://doi.org/10.1016/S0379-7112(01)00005-4.
Dilek, U. 2007. “Assessment of fire damage to a reinforced concrete structure during construction.” J. Perform. Constr. Facil. 21 (4): 257–263. https://doi.org/10.1061/(ASCE)0887-3828(2007)21:4(257).
Eamon, C. D., and E. Jensen. 2013. “Reliability analysis of reinforced concrete columns exposed to fire.” Fire Saf. J. 62: 221–229. https://doi.org/10.1016/j.firesaf.2013.10.002.
El-Hawary, M. M., A. M. Ragab, A. A. El-Azim, and S. Elibiari. 1996. “Effect of fire on flexural behaviour of RC beams.” Constr. Build. Mater. 10 (2): 147–150. https://doi.org/10.1016/0950-0618(95)00041-0.
Ervine, A., M. Gillie, T. J. Stratford, and P. Pankaj. 2012. “Thermal propagation through tensile cracks in reinforced concrete.” J. Mater. Civ. Eng. 24 (5): 516–522. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000417.
Folic, R., V. Radonjanin, and M. Malesev. 2002. “The assessment of the structure of Novi Sad Open University damage in a fire.” Constr. Build. Mater. 16 (7): 427–440. https://doi.org/10.1016/S0950-0618(02)00045-4.
Georgali, B., and P. E. Tsakiridis. 2005. “Microstructure of fire damaged concrete. A case study.” Cem. Concr. Compos. 27 (2): 255–259. https://doi.org/10.1016/j.cemconcomp.2004.02.022.
Ha, T., J. Ko, S. Lee, S. Kim, J. Jung, and D.-J. Kim. 2016. “A case study on the rehabilitation of a fire-damaged structure.” Appl. Sci. 6 (5): 126. https://doi.org/10.3390/app6050126.
Hager, I. 2014. “Colour change in heated concrete.” Fire Technol. 50 (4): 945–958. https://doi.org/10.1007/s10694-012-0320-7.
Hager, I., and T. Tracz. 2010. “The impact of the amount and length of fibrillated polypropylene fibers on the properties of HPC exposed to high temperature.” Arch. Civ. Eng. 56 (1): 57–68. https://doi.org/10.2478/v.10169-010-0003-z.
Han, Y., Y. Xie, W. Wang, R. Jiang, and K. Yin. 2012. “Determining the fire damage temperature of concrete by inclusion decrepitation.” Fire Saf. J. 47: 40–45. https://doi.org/10.1016/j.firesaf.2011.09.008.
Hertz, K. D. 2003. “Limits of spalling of fire-exposed concrete.” Fire Saf. J. 38 (2): 103–116. https://doi.org/10.1016/S0379-7112(02)00051-6.
Hertz, K. D. 2004. “Reinforcement data for fire safety design.” Mag. Concr. Res. 56 (8): 453–459. https://doi.org/10.1680/macr.2004.56.8.453.
Hertz, K. D. 2005. “Concrete strength for fire safety design.” Mag. Concr. Res. 57 (8): 445–453. https://doi.org/10.1680/macr.2005.57.8.445.
Huang, Z. 2010. “The behaviour of reinforced concrete slabs in fire.” Fire Saf. J. 45 (5): 271–282. https://doi.org/10.1016/j.firesaf.2010.05.001.
ICC (International Code Council). 2012. International building code (IBC). Country Clubs Hills, IL: ICC.
ISO. 1984. Paints and varnishes—Colorimetry. Part 1: Principles. ISO 7724-1. Geneva: ISO.
ISO. 1999. Fire-resistance tests: Elements of building construction. ISO 834. Geneva: ISO.
Khan, M. S., J. Prasad, and H. Abbas. 2010. “Shear strength of RC beams subjected to cyclic thermal loading.” Constr. Build. Mater. 24 (10): 1869–1877. https://doi.org/10.1016/j.conbuildmat.2010.04.016.
Khan, M. S., J. Prasad, and H. Abbas. 2013. “Bond strength of RC beams subjected to cyclic thermal loading.” Constr. Build. Mater. 38: 644–657. https://doi.org/10.1016/j.conbuildmat.2012.09.018.
Khoury, G. A., and Y. Anderberg. 2000. Concrete spalling review, fire safety design: Report, 1–60. Borlänge, Sweden: Swedish National Road Administration.
Kızılkanat, A., N. Yüzer, and N. Kabay. 2013. “Thermo-physical properties of concrete exposed to high temperature.” Constr. Build. Mater. 45 (Aug): 147–161. https://doi.org/10.1016/j.conbuildmat.2013.03.080.
Kodur, V., M. Dwaikat, and R. Fike. 2010. “High-temperature properties of steel for fire resistance modeling of structures.” J. Mater. Civ. Eng. 22 (5): 423–434. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000041.
Lakhani, H., T. Singh, A. Sharma, G. R. Reddy, and R. K. Singh. 2014. “Prediction of post fire load deflection response of RC flexural members using simplistic numerical approach.” Struct. Eng. Mech. 50 (6): 755–772. https://doi.org/10.12989/sem.2014.50.6.755.
Law, A., P. Kotsovinos, and N. Butterworth. 2015. “Engineering geometrically bi-linear columns to deliver fire resistance: Standard heating.” Eng. Struct. 100: 590–598. https://doi.org/10.1016/j.engstruct.2015.06.046.
Lee, J., K. Choi, and K. Hong. 2010. “The effect of high temperature on color and residual compressive strength of concrete.” In Vol. 3 of Proc., 7th Int. Conf. on Fracture Mechanics of Concrete and Concrete Structures. High Performance, Fiber Reinforced Concrete, Special Loadings and Structural Applications, edited by B. H. Oh et al., 1772–1775. Jeju, Korea.
Li, B., Y.-L. Dong, and D. S. Zhang. 2015. “Fire behaviour of continuous reinforced concrete slabs in a full scale multi-storey steel-framed building.” Fire Saf. J. 71: 226–237. https://doi.org/10.1016/j.firesaf.2014.11.021.
Lin, W.-M., T. D. Lin, and L. J. Powers-Couche. 1996. “Microstructures of fire-damaged concrete.” ACI Mater. J. 93 (3): 199–205.
Ma, Q., R. Guo, Z. Zhao, Z. Lin, and K. He. 2015. “Mechanical properties of concrete at high temperature—A review.” Constr. Build. Mater. 93: 371–383. https://doi.org/10.1016/j.conbuildmat.2015.05.131.
Mlakar, P. F., D. O. Dusenberry, J. R. Harris, G. Haynes, L. T. Phan, and M. A. Sozen. 2005. “Response to fire exposure of the pentagon structural elements.” J. Perform. Constr. Facil. 19 (3): 212–219. https://doi.org/10.1061/(ASCE)0887-3828(2005)19:3(212).
Ozawa, M., S. Uchida, T. Kamada, and H. Morimoto. 2012. “Study of mechanism of explosive spalling in high-strength concrete at high temperatures using acoustic emission.” Constr. Build. Mater. 37: 621–628. https://doi.org/10.1016/j.conbuildmat.2012.06.070.
Rush, D., and D. Lange. 2017. “Towards a fragility assessment of a concrete column exposed to a real fire: Tisova fire test.” Eng. Struct. 150: 537–549. https://doi.org/10.1016/j.engstruct.2017.07.071.
Shah, A. H., U. K. Sharma, P. Kamath, P. Bhargava, G. R. Reddy, and T. Singh. 2016. “Effect of ductile detailing on the performance of a reinforced concrete building frame subjected to earthquake and fire.” J. Perform. Constr. Facil. 30 (5): 04016035. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000881.
Shi, X., T. Tan, K. Tan, and Z. Guo. 2004. “Influence of concrete cover on fire resistance of reinforced concrete flexural members.” J. Struct. Eng. 130 (8): 1225–1232. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:8(1225).
Tanyıldızı, H., and A. Coşkun. 2008. “Performance of lightweight concrete with silica fume after high temperature.” Constr. Build. Mater. 22 (10): 2124–2129. https://doi.org/10.1016/j.conbuildmat.2007.07.017.
Topçu, I. B., and C. Karakurt. 2008. “Properties of reinforced concrete steel rebar exposed to high temperatures.” In Research letters in material science.
TSE (Turkish Standards Institution). 2010. Assessment of in-situ compressive strength in structures and precast concrete components. TS EN 13781. Ankara, Turkey: TSE.
Ünlüoğlu, E., I. B. Topçu, and B. Yaslaman. 2007. “Concrete cover effect on reinforced concrete bars exposed to high temperatures.” Constr. Build. Mater. 21 (6): 1155–1160. https://doi.org/10.1016/j.conbuildmat.2006.11.019.
Wang, Y., G. Yuan, Z. Huang, J. Lyv, Z.-Q. Li, and T.-Y. Wang. 2016. “Experimental study on the fire behaviour of reinforced concrete slabs under combined uni-axial in-plane and out-of-plane loads.” Eng. Struct. 128: 316–332. https://doi.org/10.1016/j.engstruct.2016.09.054.
Yin, K., Y. Han, and Y. Liu. 2011. “Experimental research on bond strength between rebar and concrete after high temperature.” Appl. Mech. Mater. 71: 1057–1061. https://doi.org/10.4028/www.scientific.net/AMM.71-78.1057.
Yüzer, N., B. Akbaş, and A. B. Kızılkanat. 2007. “Predicting the compressive strength of concrete exposed to high temperatures with a neural network model.” In Proc., 3rd Int. Symp., Sustainability in Cement and Concrete. Istanbul, Turkey: Turkish Cement Manufacturers’ Association.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Feb 8, 2018
Accepted: Feb 8, 2019
Published online: Jun 20, 2019
Published in print: Oct 1, 2019
Discussion open until: Nov 20, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.