Resilience Evaluation of Seismically Detailed Reinforced Concrete-Block Shear Walls for Blast-Risk Assessment
Publication: Journal of Performance of Constructed Facilities
Volume 30, Issue 4
Abstract
The increased demand for resilient infrastructure under accidental or deliberate explosions has resulted in the urgent need to quantify the performance of both existing and new building components under such extreme loading events. The current study focuses on evaluating the resilience of reinforced masonry (RM) shear wall systems under blast, which is accomplished by quantifying the walls’ blast response in the out-of-plane direction and the resulting damage levels. In seismic zones, such RM walls are detailed to resist in-plane loads in a ductile manner, and thus minimal damage is usually expected. Given that blast resistant design of civilian buildings only recently has been formally introduced in North American design standards, quantifying the out-of-plane response and ductility capacities of RM shear walls has not been common practice in mainstream building design. In this paper, a nonlinear single-degree-of-freedom (SDOF) model is developed to predict the out-of-plane response of RM wall components under blast loading. The SDOF model is first validated by using live explosive (free-field) test results. Subsequently, the model is used to perform a numerical investigation beyond the range of experimental parameters adopted in the test program, by considering a number of wall design characteristics such as wall reinforcement ratio, concrete block size and strength, wall height, and reinforcement arrangements; a wider range of design basis threat levels––identified by charge-mass and standoff-distance combinations––is also considered. In general, the study indicates that RM walls are capable of withstanding substantial explosions, which would result in different damage intensities depending on the wall vulnerability and blast hazard levels. The study also shows that significant reduction in the wall out-of-plane response can be achieved by using two layers of reinforcement instead of the typical single layer in RM walls, even in the case of reduced reinforcement ratio. The SDOF model is also used to develop RM wall performance charts that can be further refined to serve as design guidelines for the purpose of blast risk mitigation in future editions of the North American blast design standards. Finally, the findings from this study indicate that RM walls that are detailed to respond in a ductile manner under in-plane seismic loads might not necessarily exhibit a ductile response when subjected to out-of-plane blast loads. The latter observation highlights the importance of adopting a holistic multihazard design approach when evaluating the vulnerability and resilience of building systems under extreme events.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was facilitated with funding provided by the Natural Sciences and Engineering Research Council of Canada (NSERC) and the Canadian Concrete Masonry Producers Association (CCMPA). Additional funding has been provided through the McMaster University Centre for Effective Design of Structures (CEDS), funded through the Ontario Research and Development Challenge Fund (ORDCF). The in-kind support of the Canada Masonry Design Centre (CMDC) and the provision of mason time by Ontario Masonry Contractors Association (OMCA) are gratefully acknowledged. The authors are very grateful to the members of the Canadian Explosives Research Laboratory (CERL) who conducted the field blast tests and to the Canadian Forces for granting access to the test range.
References
Abou Zeid, B. M., El-Dakhakhni, W. W., Razaqpour;, A. G., and Foo, S. (2014). “Time-response analysis of arching unreinforced concrete block walls subjected to blast loads.” J. Struct. Eng., 04013099.
ASCE. (2011). “Blast protection of building.” ASCE/SEI 59-11, Reston, VA.
ASTM. (2011). “Standard test methods for compressive strength of masonry prisms.” ASTM C1314-11, West Conshohocken, PA.
Baker, W. E., Cox, P. A., Westine, P. S., Kulesz, J. J., and Strehlow, R. A. (1983). Explosion hazards and evaluation, Elsevier, Amsterdam, Netherlands.
Biggs, J. M. (1964). Introduction to structural dynamics, McGraw-Hill, New York.
Bischoff, P. H., and Perry, S. H. (1991). “Compressive behaviour of concrete at high strain rates.” J. Mater. Struct., 24(6), 425–450.
Bruneau, M., et al. (2003). “A framework to quantitatively assess and enhance the seismic resilience of communities.” Earthquake Spectra, 19(4), 733–752.
Bruneau, M., and Reinhorn, A. M. (2007). “Exploring the concept of seismic resilience for acute care facilities.” Earthquake Spectra, 23(1), 41–62.
CEB (Comité Euro-International du Béton). (1988). “Concrete structures under impact and impulsive loading.” CEB Bulletin 187, Lausanne, Switzerland.
Chang, S., and Shinozuka, M. (2004). “Measuring improvements in the disaster resilience of communities.” Earthquake Spectra, 20(3), 739–755.
Cimellaro, G. P., Reinhorn, A. M., and Bruneau, M. (2010). “Seismic resilience of a hospital system.” Struct. Infrastruct. Eng., 6(1–2), 127–144.
Coughlin, A. M., Musselman, E. S., Schokker, A. J., and Linzell, D. G. (2010). “Behavior of portable fiber reinforced concrete vehicle barriers subject to blasts from contact charges.” Int. J. Impact Eng., 37(5), 521–529.
CSA (Canadian Standards Association). (2012). “Design and assessment of buildings subjected to blast loads.” CAN/CSA S850-12, Mississauga, ON, Canada.
CSA (Canadian Standards Association). (2014). “Design of masonry structures.” CAN/CSA S304-14, Mississauga, ON, Canada.
Cutter, S. L., Burton, C. G., and Emrich, C. T. (2010). “Disaster resilience indicators for benchmarking baseline conditions.” J. Homeland Secur. Emergency Manage., 7(1), Article 51.
Davidson, J., Fisher, J., Hammons, M., Porter, J., and Dinan, R. (2005). “Failure mechanisms of polymer-reinforced concrete masonry walls subjected to blast.” J. Struct. Eng., 1194–1205.
Dusenberry, D. O. (2010). Handbook for blast resistant design of buildings, 1st Ed., Wiley, Hoboken, NJ.
ElSayed, M., El-Dakhakhni, W., and Tait, M. (2015). “Response evaluation of reinforced concrete block structural walls subjected to blast loading.” J. Struct. Eng., 04015043.
FEMA (Federal Emergency Management Agency). (2003). “Primer to design safe school projects in case of terrorist attacks.” FEMA 428, Washington, DC.
Hamed, E., and Rabinovitch, O. (2008). “Nonlinear dynamic behavior of unreinforced masonry walls subjected to out-of-plane loads.” J. Struct. Eng., 1743–1753.
Hrynyk, T. D., and Myers, J. J. (2008). “Out-of-plane behavior of URM arching walls with modern blast retrofits: Experimental results and analytical model.” J. Struct. Eng., 1589–1597.
Jacques, C. C., McIntosh, J., Giovinazzi, S., Kirsch, T. D., Wilson, T., and Mitrani-Reiser, J. (2014). “Resilience of the Canterbury hospital system to the 2011 Christchurch earthquake.” Earthquake Spectra, 30(1), 533–554.
Krauthammer, T., Bazeos, N., and Holmquist, T. J. (1986). “Modified SDOF analysis of RC box-type structures.” J. Struct. Eng., 726–744.
Krauthammer, T., Shahriar, S., and Shanaa, H. M. (1990). “Response of reinforced concrete elements to severe impulsive loads.” J. Struct. Eng., 1061–1079.
Li, J., and Hao, H. (2014). “Numerical study of concrete spall damage to blast loads.” Int. J. Impact Eng., 68, 41–55.
Malvar, L. J. (1998). “Review of static and dynamic properties of steel reinforcing bars.” ACI Mater. J., 95(5), 609–616.
Manyena, S. B. (2006). “The concept of resilience revisited.” Disasters, 30(4), 434–450.
Marjanishvili, S., and Katz, B. (2014). “A performance-based framework for structural resilience to blast-induced damage.” 10th Int. Conf. of the Int. Institute for Infrastructure Resilience and Reconstruction, Purdue Univ., West Lafayette, IN.
Mayrhofer, C. (2002). “Reinforced masonry walls under blast loading.” Int. J. Mech. Sci., 44(6), 1067–1080.
Mieler, M., Stojadinovic, B., Budnitz, R., Comerio, M., and Mahin, S. (2014). “A framework for linking community-resilience goals to specific performance targets for the built environment.” Earthquake Spectra, 31(3), 1267–1283.
Mieler, M. W., Stojadinovic, B., Budnitz, R. J., Mahin, S. A., and Comerio, M. C. (2013). “Toward resilient communities: A performance-based engineering framework for design and evaluation of the built environment.”, Pacific Earthquake Engineering Research Center, Berkeley, CA.
MSJC (Masonry Standards Joint Committee). (2013). “Building code requirements and specification for masonry structures.”, American Concrete Institute, Farmington Hills, MI, 6–13.
Nassr, A. A., Razaqpur, A. G., Tait, M., Campidelli, M., and Foo, S. (2013). “Dynamic response of steel columns subjected to blast loading.” J. Struct. Eng., 04014036.
Nassr, A. A., Razaqpur, A. G., Tait, M. J., Campidelli, M., and Foo, S. (2012). “Single and multi degree of freedom analysis of steel beams under blast loading.” Nucl. Eng. Des., 242(1), 63–77.
Natio, C. J., and Wheaton, K. P. (2006). “Blast assessment of load-bearing reinforced concrete shear walls.” J. Struct. Eng., 11(2), 112–121.
NRC (National Research Council). (2012). Disaster resilience: A national imperative, National Academies Press, Washington, DC.
Priestley, M. J. N., Calvi, G. M., and Kowalsky, M. J. (2007). Displacement based seismic design of structures, 1st Ed., IUSS Press, Pavia, Italy.
Silva, P. F., and Lu, B. (2009). “Blast resistance capacity of reinforced concrete slabs.” J. Struct. Eng., 708–716.
Stolz, A., Fischer, K., and Lu, B. (2014). “Dynamic bearing capacity of ductile concrete plates under blast loading.” Int. J. Impact Eng., 69, 25–38.
Tomaževič, M. (1999). Earthquake resistant design of masonry buildings, Imperial College Press, London.
Twigg, J. (2009). Characteristics of a disaster-resilient community: A guidance note, 2nd Ed., Disaster Risk Reduction Interagency Coordination Group, London.
Urgessa, G., and Maji, A. (2010). “Dynamic response of retrofitted masonry walls for blast loading.” J. Eng. Mech., 858–864.
USACE (U.S. Army Corps of Engineers). (2008). “Structures to resist the effect of accidental explosions.” UFC 3-340-02, Naval Facilities Engineering Command, and Air Forces Civil Engineer Support Agency, Washington, DC.
Warn, G. P., and Bruneau, M. (2009). “Blast resistance of steel plate shear walls designed for seismic loading.” J. Struct. Eng., 1222–1230.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Jun 23, 2014
Accepted: Jun 4, 2015
Published online: Oct 27, 2015
Discussion open until: Mar 27, 2016
Published in print: Aug 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.