Seismic Performance of Storage Steel Tanks during the May 2012 Emilia, Italy, Earthquakes
Publication: Journal of Performance of Constructed Facilities
Volume 29, Issue 5
Abstract
Field observations following the May 2012 Emilia, Italy, earthquakes have revealed the seismic vulnerability of storage steel tanks typical of the past Italian design practice, highlighting structural deficiencies observed during previous events in other areas and mostly related to lack of structural seismic design and detailing, lack of redundancy, and inadequate anchorage design and execution. Damage was disproportionately high, considering the moderate size of the events ( and on 20th and 29th May, respectively). Failure modes observed are reported and classified. Comparison is provided with the results of high-definition finite element (FE) dynamic simulations, performed on tanks representative of those inspected. Numerical analyses, accounting for material and geometrical nonlinearities, at the element level, as well as for fluid-structure interaction through highly nonlinear methods, were able to capture the stress/strain concentrations that caused them to collapse. Elephant’s foot and diamond buckling induced by hydrodynamic pressures as a result of inertial forces imparted during the earthquakes were reproduced, as well as shear-buckling failure of leg-supported tanks or sliding of unanchored systems.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Concrete Institute (ACI). (1998). “Guide for the analysis, design and construction of concrete-pedestal water towers.”, Farmington Hills, MI.
American Concrete Institute (ACI). (2006). “Seismic design of liquid containing structures and commentary.”, Farmington Hills, MI.
American Petroleum Institute Standards (API). (2012). “Design and construction of large, welded, low-pressure storage tanks.”, Washington, DC.
American Petroleum Institute Standards (API). (2012). “Welded steel tanks for oil storage.”, Washington, DC.
American Society of Civil Engineers (ASCE). (2010). “Minimum design loads for buildings and other structures.”, Reston, VA.
American Water Works Association (AWWA). (2004). “Wire and strand-wound, circular, prestressed concrete water tanks.”, Denver, CO.
American Water Works Association (AWWA). (2006). “Tendon-prestressed concrete water tanks.”, Denver, CO.
American Water Works Association (AWWA). (2009). “Factory-coated bolted carbon steel tanks for water storage.”, Denver, CO.
American Water Works Association (AWWA). (2011). “Welded carbon steel tanks for water storage.”, Denver, CO.
Architectural Institute of Japan (AIJ). (2010). Design recommendation for storage tanks and their supports with emphasis on seismic design, Tokyo, Japan.
Belleri, A., Brunesi, E., Nascimbene, R., Pagani, M., and Riva, P. (2014). “Field observations and seismic performance of precast industrial structures following the 2012 Emilia earthquakes.” J. Peform. Constr. Facil., in press.
Belytschko, T., Lin, J., and Tsay, C. S. (1984). “Explicit algorithms for nonlinear dynamics of shells.” Comput. Meth. Appl. Mech. Eng., 42(2), 225–251.
Bournas, D. A., Negro, P., and Taucer, F. F. (2013). “Performance of industrial buildings during the Emilia earthquakes in Northern Italy and recommendations for their strengthening.” Bull. Earthquake Eng.
Buratti, N., and Tavano, M. (2014). “Dynamic buckling and seismic fragility of anchored steel tanks by the added mass method.” Earthquake Eng. Struct. Dyn., 43(1), 1–21.
Castro, R., et al. (2013). “The 2012 May 20 and 29, Emilia earthquakes (Northern Italy) and the main aftershocks: -wave attenuation, acceleration source functions and site effects.” Geophys. Res. Lett., 195, 597–611.
Cultrera, G., Faenza, L., Meletti, C., D’Amico, V., Michelini, A., and Amato, A. (2014). “Shakemaps uncertainties and their effects in the post-seismic actions for the 2012 Emilia (Italy) earthquakes.” Bull. Earthquake Eng.
DM 3/12/1987. (1987). Italian building code—Technical recommendations for design, execution and testing of precast structures, Rome, Italy (in Italian).
DM 16/01/1996. (1996). Italian building code—Technical recommendations for design in seismic zones, Rome, Italy (in Italian).
European and Mediterranean Regional Centroid Moment Tensor Solution (RCMT). (1997). “European-Mediterranean RCMT Catalogue.” 〈http://www.bo.ingv.it/RCMT/〉 (Mar. 2014).
González, E., Almazán, J., Beltrán, J., Herrera, R., and Sandoval, V. (2013). “Performance of stainless steel winery tanks during the 02/27/2010 Maule Earthquake.” Eng. Struct., 56, 1402–1418.
Hughes, T. J. R., and Liu, W. K. (1981). “Nonlinear finite element analysis of shells: Part II. Three-dimensional shells.” Comput. Meth. Appl. Mech. Eng., 26(3), 331–362.
Indian Institute of Technology (IIT). (2005). “Guidelines for seismic design of liquid storage tanks; provisions with commentary and explanatory examples.” IITK-GSDMA, Kanpur.
Istituto Nazionale di Geofisica e Vulcanologia (INGV). (2009). “Italian seismic hazard map.” 〈http://zonesismiche.mi.ingv.it〉 (Mar. 2014).
Italian Seismological Instrumental and Parametric Database (ISIDe). (2012). “Italian seismic bulletin.” 〈http://iside.rm.ingv.it〉 (Mar. 2014).
Koketsu, K., and Miyake, H. (2008). “A seismological overview of long-period ground motion.” J. Seismolog., 12(2), 133–143.
LS-DYNA theory manual. (2006). Livermore Software Technology Corporation, Livermore, CA.
Luzi, L., et al. (2013). “Overview of the strong-motion data recorded during the May-June 2012 Emilia Seismic Sequence.” Seismol. Res. Lett., 84(4), 629–644.
Magliulo, G., Ercolino, M., Petrone, C., Coppola, O., and Manfredi, G. (2013). “Emilia earthquake: The seismic performance of precast RC buildings.” Earthquake Spectra.
Manos, G. (1991). “Evaluation of the earthquake performance of anchored wine tanks during the San Juan, Argentina, 1977 Earthquake.” Earthquake Eng. Struct. Dyn., 20(12), 1099–1114.
Massa, M., et al. (2012). “INGV strong-motion data web-portal: a focus on the Emilia seismic sequence of May-June 2012.” Ann. Geophys., 55(4), 829–835.
Meletti, C., D’Amico, V., Ameri, G., Rovida, A., and Stucchi, M. (2012). “Seismic hazard in the Po Plain and the 2012 Emilia earthquakes.” Ann. Geophys., 55(4), 623–629.
Moslemi, M., and Kianoush, M. R. (2012). “Parametric study on dynamic behavior of cylindrical ground-supported tanks.” Eng. Struct., 42, 214–230.
Niwa, A., and Clough, R. (1982). “Buckling of cylindrical liquid-storage tanks under earthquake loading.” Earthquake Eng. Struct. Dyn., 10(1), 107–122.
NZSEE. (2009). Recommendations for seismic design of storage tanks, New Zealand National Society for Earthquake Engineering.
Ozdemir, Z., Souli, M., and Fahjan, Y. M. (2010). “Application of nonlinear fluid-structure interaction methods to seismic analysis of anchored and unanchored tanks.” Eng. Struct., 32(2), 409–423.
Pacor, F., et al. (2011). “Overview of the Italian strong motion database ITACA 1.0.” Bull. Earthquake Eng., 9(6), 1723–1739.
Rotter, J. M., Cai, M., Holst, J. M. F. G. (2011). “Buckling of thin cylindrical shells under locally elevated compressive stresses.” J. Pressure Vessel Technol., 133(1), 011204.
Sezen, H., Livaoglu, R., and Dogangun, A. (2008). “Dynamic analysis and seismic performance evaluation of above-ground liquid-containing tanks.” Eng. Struct., 30(3), 794–803.
ShakeMap Working Group. (2014). “The maps of ground shaking.” 〈http://shakemap.rm.ingv.it〉 (Mar. 2014).
Stepp, J. C., et al. (1990). “Loma Prieta earthquake reconnaissance report. Industrial facilities.” Earthquake Spectra, 6, 189–238.
Stucchi, M., Meletti, C., Montaldo, V., Crowley, H., Calvi, G. M., and Boschi, E. (2011). “Seismic hazard assessment (2003–2009) for the Italian building code.” Bull. Seismol. Soc. Am., 101(4), 1885–1911.
Swan, W., Miller, D., and Yanev, P. (1985). “The Morgan hill earthquake of April 24, 1984—Effects on industrial facilities, buildings, and other facilities.” Earthquake Spectra, 1(3), 457–568.
UNI EN 14015. (2006). “Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded steel tanks for the storage of liquids at ambient temperature and above.” European Committee for Standardization (CEN), Brussels, Belgium.
Virella, J. C., Godoy, L. A., and Suárez, L. E. (2006). “Fundamental modes of tank-liquid systems under horizontal motions.” Eng. Struct., 28(10), 1450–1461.
Zareian, F., Sampere, C., Sandoval, V., McCormick, D. L., Moehle, J., and Leon, R. (2012). “Reconnaissance of the Chilean Wine Industry Affected by the 2010 Chile Offshore Maule Earthquake.” Earthquake Spectra, 28, S503–S512.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Mar 19, 2014
Accepted: May 12, 2014
Published online: Sep 12, 2014
Discussion open until: Feb 12, 2015
Published in print: Oct 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.