Design of Metal Foam Cladding Subjected to Close-Range Blast
Publication: Journal of Performance of Constructed Facilities
Volume 29, Issue 4
Abstract
The response of a blast mitigation cladding consisting of a face sheet and metal foam core subjected to a close-range blast is predicted. Whereas the cladding is sufficiently wide compared to the standoff distance between the explosion center and the cladding, the boundary of the blast induced bulge is released. The face sheet is considered as a rigid perfectly plastic membrane as the deformation of the sheet always exceeds half its thickness. A procedure predicting the depth and extent of the bulge is proposed with energy method. Subsequently, the minimum thickness of the foam layer is calculated based on the bulge depth. This design-oriented approach, in a ready-to-use manner, can be straightforwardly applied, facilitating the preliminary design of blast mitigation claddings with metal foam core.
Get full access to this article
View all available purchase options and get full access to this article.
References
Ashby, M. F., Evans, A., Fleck, N. A., Gibson, L. J., Hutchinson, J. W., and Wadley, H. N. G. (2000). Metal foams: A design guide, Butterworth-Heinmann, Woburn.
Biggs, J. M. (1964). Introduction to structural dynamics, McGraw-Hill, New York.
Gibson, L. J., and Ashby, M. F. (1997). Cellular solids: Structures and properties, 2nd Ed., Cambridge University Press, Cambridge, U.K.
Goel, M. D., Matsagar, V. A., Marburg, S., and Gupta, A. K. (2013). “Comparative performance of stiffened sandwich foam panels under impulsive loading.” J. Perform. Constr. Facil., 540–549.
Jones, N. (1989). Structural impact, Cambridge University Press, Cambridge, U.K.
Kennedy, J. B., and Iyengar, K. J. (1981). “Behavior of viscoplastic circular plates under Gaussian impulse.” Nucl. Eng. Des., 64(1), 117–128.
Liu, H., Cao, Z. K., Yao, G. C., Luo, H. J., and Zu, G. Y. (2013). “Performance of aluminum foam-steel panel sandwich composites subjected to blast loading.” Mater. Des., 47, 483–488.
Lu, G. X., and Yu, T. X. (2003). Energy absorption of structures and materials, CRC Press, Boca Raton.
Ma, G. W., and Ye, Z. Q. (2007). “Analysis of foam claddings for blast alleviation.” Int. J. Impact Eng., 34(1), 60–70.
Qiu, X., Deshpande, V. S., and Fleck, N. A. (2004). “Dynamic response of a clamped circular sandwich plate subject to shock loading.” J. Appl. Mech., 71(5), 637–645.
Ramu, S. A., and Iyengar, K. J. (1976). “Plastic response of orthotropic circular plates under blast loading.” Int. J. Solids Struct., 12(2), 125–133.
Reid, S. R., and Peng, C. (1997). “Dynamic uniaxial crushing of wood.” Int. J. Impact Eng., 19(5–6), 531–570.
Shen, J. H., Lu, G. X., Zhao, L. M., and Qu, Z. H. (2011). “Response of curved sandwich panels subjected to blast loading.” J. Perform. Constr. Facil., 382–393.
Smith, P. D., and Hetherington, J. G. (1994). Blast and ballistic loading of structures, Butterworth-Heinemann, Oxford, U.K.
Teeling-Smith, R. G., and Nurick, G. N. (1991). “The deformation and tearing of thin circular plates subjected to impulsive loads.” Int. J. Impact Eng., 11(1), 77–91.
Thomas, G. B., Weir, M. D., and Hass, J. (2010). Thomas’ calculus, 12th Ed., Pearson Education, Boston, MA.
U.S. Army. (1986). “Fundamentals of protective design for conventional weapons.”.
U.S. Army Corps of Engineers, Naval Facilities Engineering Command, and Air Force Civil Engineer Support Agency. (2008). “Structures to resist the effects of accidental explosions.”.
Wu, C. Q., Huang, L., and Oehlers, D. J. (2011). “Blast testing of aluminum foam- protected reinforced concrete slabs.” J. Perform. Constr. Facil., 464–474.
Xue, Z., and Hutchinson, J. W. (2003). “Preliminary assessment of sandwich plates subjected to blast loads.” Int. J. Mech. Sci., 45(4), 687–705.
Ye, Z. Q., and Ma, G. W. (2007). “Effects of foam claddings for structure protection against blast loads.” J. Eng. Mech., 41–47.
Zhu, F., Wang, Z. H., Lu, G. X., and Zhao, L. M. (2009). “Analytical investigation and optimal design of sandwich panels subjected to shock loading.” Mater. Des., 30(1), 91–100.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Oct 31, 2013
Accepted: Mar 3, 2014
Published online: Mar 5, 2014
Discussion open until: Jan 28, 2015
Published in print: Aug 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.