Seismic Performance Parameters for Reinforced Concrete-Block Shear Wall Construction
Publication: Journal of Performance of Constructed Facilities
Volume 24, Issue 1
Abstract
The focus of the current study is to analyze previously reported test results to evaluate equivalent plastic hinge lengths for concrete-block shear walls and to extract related seismic performance parameters. Inelastic curvatures at the base of the walls are the main source of plastic deformation for flexurally dominated walls. With adequate estimation of the plastic hinge length and more realistic values for inelastic curvatures at the base of the wall, top wall displacement can be predicted more accurately. For the walls analyzed, measured compressive strains close to the base of the wall at maximum load were significantly higher than the strains specified by North American codes. The strains, although may not alter the wall strength, significantly affect the displacement ductility at maximum load. The analysis showed that the equivalent plastic hinge length varied between approximately 30 and 60% of the wall length at a drift of 1%. The product of the seismic force modification factors (for ductility and overstrength) varied between 3 and 6. The plastic hinge length and the seismic force modification factors were found to depend not only on the factors prescribed in North American codes but on the amount of vertical reinforcement and axial stress level as well. This study draws a road map for further research to facilitate better understanding and provide more realistic methods to predict the seismic performance of masonry shear wall construction.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study forms a part of ongoing masonry research in McMaster University Centre for Effective Design of Structures (CEDS) funded through the Ontario Research and Development Challenge Fund (ORDCF) of the Ministry of Research and Innovation (MRI). This research falls under CEDS Focus Area I: Masonry Structures, and CEDS Focus Area: Earthquake Engineering. The financial support of the Centre is gratefully appreciated. Provision of mason time by Ontario Masonry Contractors Association (OMCA) and Canada Masonry Design Centre (CMDC) is appreciated. The supply of the concrete blocks and grout by Boehmer Block Ltd. is gratefully acknowledged.
References
Applied Technology Council (ATC). (2008). “Quantification of building seismic performance factors.” ATC-63 Project Rep., Applied Technology Council, Redwood City, Calif. (90% draft).
ASCE. (2008). “Minimum design loads for buildings and other structures.” ASCE7-08, Reston, Va.
Canadian Standards Association (CSA). (2004). CSA S304.1-04: Design of masonry structures, CSA, Mississauga, Ont.
Chopra, A. (2000). Dynamics of structures: Theory and application to earthquake engineering, 2nd Ed., Prentice-Hall, Upper Saddle River, N.J.
Drysdale, R., and Hamid, A. (2008). Masonry structures—Behaviour and design, 1st Canadian Ed., Canada Masonry Design Centre, Mississauga, Ont.
Hose, Y., and Seible, F. (1999). “Performance evaluation database for concrete bridge components, and systems under simulated seismic loads.” PEER Rep. No. 1999/11, Pacific Earthquake Engineering Research Center, College of Engineering, University of California, Berkley.
International Building Code (IBC). (2008). International Code Council, Falls Church, Va.
Masonry Standards Joint Committee (MSJC). (2008). “Building code requirements for masonry structures.” TMS 402/ASCE 5/ACI 530, Detroit, New York, and Boulder.
Mitchell, D., Tremblay, R., Karacabeyli, E., Paultre, P., Saatcioglu, M., and Anderson, D. (2003). “Seismic force modification factors for the proposed 2005 edition of the National Building Code of Canada.” Can. J. Civ. Eng., 30, 308–327.
National Building Code of Canada (NBCC). (2005). National Building Code of Canada, Institute for Research in Construction, National Research Council of Canada, Ottawa, Ont.
National Earthquake Hazard Reduction Program (NEHRP). (1997). “NHREP guidelines for the seismic rehabilitation of buildings.” FEMA-273, National Earthquake Hazard Reduction Program, Federal Emergency Management Agency, Washington, D.C.
Park, R., and Paulay, R. (1975). Reinforced concrete structures, Wiley, New York.
Paulay, T., and Priestley, M. (1992). Seismic design of reinforced concrete and masonry buildings, Wiley, New York.
Priestley, M. (2000). “Performance based seismic design.” Proc., 12th World Conf. Earthquake Engineering, Auckland, New Zealand.
Priestley, M., Seible, F., and Calvi, G. (1996). Seismic design and retrofit of bridges, Wiley, New York.
Priestley, N., Calvi, G., and Kowalsky, M. (2007). Displacement-based seismic design of structures, IUSS, Pavia, Italy.
Shedid, M. (2006). “Ductility of reinforced concrete masonry shear walls.” MASc thesis, Dept. of Civil Engineering, McMaster Univ., Ont.
Shedid, M., Drysdale, R., and El-Dakhakhni, W. (2008). “Behavior of fully grouted reinforced concrete masonry shear walls failing in flexure: Experimental results.” J. Struct. Eng., 134(11), 1754–1767.
Shing, P., Noland, J., Klamerus, E., and Spaeh, H. (1989). “Inelastic behavior of concrete masonry shear walls.” J. Struct. Eng., 115(9), 2204–2225.
Tomazevic, M. (1998). Earthquake-resistant design of masonry buildings, Imperial College Press, Covent Garden, London, U.K.
Uang, C. (1991). “Establishing R (or ) and factors for building seismic provisions.” J. Struct. Eng., 117(1), 19–28.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: Jan 30, 2009
Accepted: Jun 3, 2009
Published online: Jun 5, 2009
Published in print: Feb 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.