Flexural Behavior of Hollow-Core Slabs Strengthened with Prestressed Basalt FRP Grids
Publication: Journal of Composites for Construction
Volume 23, Issue 3
Abstract
Numerous studies have been conducted on strengthening techniques using prestressed fiber-reinforced polymer (FRP) laminates, bars, and tendons. However, to date, no technique has been developed for prestressed FRP grids, which are an attractive solution for strengthening slabs, walls, and tunnels. In this paper, a novel waveform anchor is proposed and verified by tensile tests to be capable of feasibly and effectively anchoring the basalt FRP (BFRP) grid. Five hollow-core slabs, including one control slab and four strengthened slabs, were tested to failure to investigate the flexural behavior of slabs strengthened with prestressed BFRP grids. The effect of the anchorage system and prestressing force on the flexural performance of the slabs was studied. The test results showed that the failure mode of the prestressed BFRP grid–strengthened slabs was rupture of the BFRP grids, and no end peeling was observed. At increasing prestressing force in the BFRP grid, the failure mode changed from sequential rupture to essentially simultaneous rupture of the longitudinal bars. Thus, the flexural capacity of the strengthened slabs increased with the prestressing level of the BFRP grids. Improved cracking behavior of the slab could be obtained by prestressing the BFRP grid, and the crack width remarkably decreased as the prestressing force in the BFRP grid increased. However, the ductility of the strengthened slabs decreased with increased prestressing force in the BFRP grid.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge the financial support from the National Key Research and Development Program of China (2016YFC0701400), the National Natural Science Foundation of China (51525801), and the Scientific Research Foundation of Graduate School of Southeast University (YBJJ1821).
References
Al-Bayati, G., R. Al-Mahaidi, M. J. Hashemi, and R. Kalfat. 2018. “Torsional strengthening of RC beams using NSM CFRP rope and innovative adhesives.” Compos. Struct. 187: 190–202. https://doi.org/10.1016/j.compstruct.2017.12.016.
Al-Mayah, A., K. A. Soudki, and A. Plumtree. 2001. “Experimental and analytical investigation of a stainless steel anchorage for CFRP prestressing tendons.” PCI J. 46 (2): 88–100. https://doi.org/10.15554/pcij.03012001.88.100.
Arduini, M., and A. Nanni. 1997. “Behavior of precracked RC beams strengthened with carbon FRP sheets.” J. Compos. Constr. 1 (2): 63–70. https://doi.org/10.1061/(ASCE)1090-0268(1997)1:2(63).
Aslam, M., P. Shafigh, M. Z. Jumaat, and S. N. R. Shah. 2015. “Strengthening of RC beams using prestressed fiber reinforced polymers-A review.” Constr. Build. Mater. 82: 235–256. https://doi.org/10.1016/j.conbuildmat.2015.02.051.
Badawi, M., and K. Soudki. 2009. “Flexural strengthening of RC beams with prestressed NSM CFRP rods-Experimental and analytical investigation.” Constr. Build. Mater. 23 (10): 3292–3300. https://doi.org/10.1016/j.conbuildmat.2009.03.005.
CECS (China Association for Engineering Construction Standardization). 2007. Technical specification for strengthening concrete structure with carbon fiber reinforced polymer laminate. CECS 146. Beijing: China Planning Press.
CEN (European Committee for Standardization). 2004. Design of concrete structures—Part 1-1: General rules and rules for buildings. Eurocode 2. Brussels, Belgium: CEN.
Chen, X. Y., T. N. Li, M. Z. Chen, and Y. Huang. 2009. “Experimental research on mechanical property of anchor CFRP sheet with the wave-shaped-teeth anchor and design of anchor system.” [In Chinese.] Eng. Mech. 26 (6): 184–192.
Chinese Code. 2010. Code for design of concrete structures. GB-50010. Beijing: China Architecture and Building Press.
Choi, H. T., J. S. West, and K. A. Soudki. 2008. “Analysis of the flexural behavior of partially bonded FRP strengthened concrete beams.” J. Compos. Constr. 12 (4): 375–386. https://doi.org/10.1061/(ASCE)1090-0268(2008)12:4(375).
Czaderski, C., and M. Motavalli. 2007. “40-year-old full-scale concrete bridge girder strengthened with prestressed CFRP plates anchored using gradient method.” Composites Part B 38 (7–8): 878–886. https://doi.org/10.1016/j.compositesb.2006.11.003.
De Lorenzis, L., and J. G. Teng. 2007. “Near-surface mounted FRP reinforcement: An emerging technique for strengthening structures.” Composites Part B 38 (2): 119–143. https://doi.org/10.1016/j.compositesb.2006.08.003.
El-Hacha, R., and M. Gaafar. 2011. “Flexural strengthening of reinforced concrete beams using prestressed, near-surfacemounted CFRP bars.” PCI J. 56 (4): 134–151. https://doi.org/10.15554/pcij.09012011.134.151.
El-Hacha, R., and S. H. Rizkalla. 2004. “Near-surface-mounted fiber-reinforced polymer reinforcements for flexural strengthening of concrete structures.” ACI Struct. J. 101 (5): 717–726.
El-Hacha, R., R. G. Wight, and M. F. Green. 2003. “Innovative system for prestressing fiber-reinforced polymer sheets.” ACI Struct. J. 100 (3): 305–313.
El-Hacha, R., R. G. Wight, and M. F. Green. 2004. “Prestressed carbon fiber reinforced polymer sheets for strengthening concrete beams at room and low temperatures.” J. Compos. Constr. 8 (1): 3–13. https://doi.org/10.1061/(ASCE)1090-0268(2004)8:1(3).
Foubert, S., K. Mahmoud, and E. El-Salakawy. 2016. “Behavior of prestressed hollow-core slabs strengthened in flexure with near-surface mounted carbon fiber-reinforced polymer reinforcement.” J. Compos. Constr. 20 (6): 04016037. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000692.
Huang, H., W. W. Wang, J. G. Dai, and J. C. Brigham. 2017. “Fatigue behavior of reinforced concrete beams strengthened with externally bonded prestressed CFRP sheets.” J. Compos. Constr. 21 (3): 04016108. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000766.
Karbhari, V. M., and M. A. Abanilla. 2007. “Design factors, reliability, and durability prediction of wet layup carbon/epoxy used in external strengthening.” Composites Part B 38 (1): 10–23. https://doi.org/10.1016/j.compositesb.2006.06.001.
Kotynia, R. 2007. “Analysis of the flexural response of NSM FRP-strengthened concrete beams.” In Proc., 8th Int. Symp. on Fiber Reinforced Polymers for Reinforced Concrete Structures, 16–18. Farmington Hills, MI: American Concrete Institute.
Kotynia, R., K. Lasek, and M. Staskiewicz. 2014. “Flexural behavior of preloaded RC slabs strengthened with prestressed CFRP laminates.” J. Composite Constr. 18 (3): A4013004. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000421.
Lee, D., and L. Cheng. 2011. “Assessing the strengthening effect of various near-surface-mounted FRP reinforcements on concrete bridge slab overhangs.” J. Compos. Constr. 15 (4): 615–624. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000182.
Lee, H. Y., W. T. Jung, and W. Chung. 2017. “Flexural strengthening of reinforced concrete beams with pre-stressed near surface mounted CFRP systems.” Compos. Struct. 163: 1–12. https://doi.org/10.1016/j.compstruct.2016.12.044.
Michels, J., J. Sena-Cruz, C. Czaderski, and M. Motavalli. 2013. “Structural strengthening with prestressed CFRP strips with gradient anchorage.” J. Compos. Constr. 17 (5): 651–661. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000372.
Mimoto, T., T. Sakaki, T. Mihara, and I. Yoshitake. 2016. “Strengthening system using post-tension tendon with an internal anchorage of concrete members.” Eng. Struct. 124: 29–35. https://doi.org/10.1016/j.engstruct.2016.06.003.
Pellegrino, C., and C. Modena. 2009. “Flexural strengthening of real-scale RC and PRC beams with end-anchored pretensioned FRP laminates.” ACI Struct. J. 106 (3): 319–328.
Peng, H., J. Zhang, S. Shang, Y. Liu, and C. S. Cai. 2016. “Experimental study of flexural fatigue performance of reinforced concrete beams strengthened with prestressed CFRP plates.” Eng. Struct. 127: 62–72. https://doi.org/10.1016/j.engstruct.2016.08.026.
Pincheira, J. A., and J. P. Woyak. 2001. “Anchorage of carbon fiber reinforced polymer (CFRP) tendons using cold-swaged sleeves.” PCI J. 46 (6): 100–111. https://doi.org/10.15554/pcij.11012001.100.111.
Quattlebaum, J. B., K. A. Harries, and M. F. Petrou. 2005. “Comparison of three flexural retrofit systems under monotonic and fatigue loads.” J. Bridge Eng. 10 (6): 731–740. https://doi.org/10.1061/(ASCE)1084-0702(2005)10:6(731).
Rahimi, H., and A. Hutchinson. 2001. “Concrete beams strengthened with externally bonded FRP plates.” J. Compos. Constr. 5 (1): 44–56. https://doi.org/10.1061/(ASCE)1090-0268(2001)5:1(44).
Saqan, E. I., H. A. Rasheed, and T. Alkhrdaji. 2018. “Evaluation of the seismic performance of reinforced concrete frames strengthened with CFRP fabric and NSM bars.” Compos. Struct. 184: 839–847. https://doi.org/10.1016/j.compstruct.2017.10.069.
Sayed-Ahmed, E. Y., R. Bakay, and N. G. Shrive. 2009. “Bond strength of FRP laminates to concrete: State-of-the-art review.” Electron. J. Struct. Eng. 9 (1): 45–61.
Seim, W., M. Hörman, V. Karbhari, and F. Seible. 2001. “External FRP poststrengthening of scaled concrete slabs.” J. Compos. Constr. 5 (2): 67–75. https://doi.org/10.1061/(ASCE)1090-0268(2001)5:2(67).
Shi, J. W., H. Zhu, G. Wu, and Z. S. Wu. 2014. “Tensile behavior of FRP and hybrid FRP sheets in freeze-thaw cycling environments.” Composites Part B 60: 239–247. https://doi.org/10.1016/j.compositesb.2013.11.026.
Täljsten, B., and T. Blanksvärd. 2007. “Mineral-based bonding of carbon FRP to strengthen concrete structures.” J. Composite Constr. 11 (2): 120–128. https://doi.org/10.1061/(ASCE)1090-0268(2007)11:2(120).
Wahab, N., K. A. Soudki, and T. Topper. 2012. “Experimental investigation of bond fatigue behavior of concrete beams strengthened with NSM prestressed CFRP rods.” J. Compos. Constr. 16 (6): 684–692. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000298.
Woo, S. K., J. W. Nam, J. H. J. Kim, S. H. Han, and K. J. Byun. 2008. “Suggestion of flexural capacity evaluation and prediction of prestressed CFRP strengthened design.” Eng. Struct. 30 (12): 3751–3763. https://doi.org/10.1016/j.engstruct.2008.06.013.
Wu, G., Z. Q. Dong, X. Wang, Y. Zhu, and Z. S. Wu. 2015a. “Prediction of long-term performance and durability of BFRP bars under the combined effect of sustained load and corrosive solutions.” J. Compos. Constr. 19 (3): 04014058. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000517.
Wu, G., Z. Q. Dong, Z. S. Wu, and L. W. Zhang. 2014a. “Performance and parametric analysis of flexural strengthening for RC beams with NSM-CFRP bars.” J. Compos. Constr. 18 (4): 04013051. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000451.
Wu, G., J. W. Shi, W. J. Jing, and Z. S. Wu. 2014b. “Flexural behavior of concrete beams strengthened with new prestressed carbon-basalt hybrid fiber sheets.” J. Compos. Constr. 18 (4): 04013053. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000452.
Wu, G., X. Zhao, J. Zhou, and Z. Wu. 2015b. “Experimental study of RC beams strengthened with prestressed steel-wire BFRP composite plate using a hybrid anchorage system.” J. Compos. Constr. 19 (2): 04014039. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000499.
Yang, D. S., S. K. Park, and K. W. Neale. 2009. “Flexural behaviour of reinforced concrete beams strengthened with prestressed carbon composites.” Compos. Struct. 88 (4): 497–508. https://doi.org/10.1016/j.compstruct.2008.05.016.
Yost, J., S. Gross, D. Dinehart, and J. Mildenberg. 2007. “Flexural behavior of concrete beams strengthened with near-surface-mounted CFRP strips.” ACI Struct. J. 104 (4): 430–437.
Zhang, S. S., T. Yu, and G. M. Chen. 2017. “Reinforced concrete beams strengthened in flexure with near-surface mounted (NSM) CFRP strips: Current status and research needs.” Composites Part B 131: 30–42. https://doi.org/10.1016/j.compositesb.2017.07.072.
Zhou, Y., X. Chen, Z. Fan, L. Sui, D. Li, and F. Xing. 2017. “Bond behaviors of FRP-to-concrete interface under the control of a novel end-anchorage system.” Compos. Struct. 168: 130–142. https://doi.org/10.1016/j.compstruct.2017.02.056.
Zhuo, J., and T. Li. 2004a. “An innovative WSGG anchor of FRP sheet.” In Proc., 4th Int. Conf. on Advanced Composite Materials in Bridges and Structures, 8–86. Calgary, Canada: Univ. of Calgary.
Zhuo, J., and T. Li. 2004b. “The mechanism of an innovative WSGG anchor of FRP laminations.” In Vol. 7 of Proc., 8th Int. Symp. on Structural Engineering for Young Experts, 805–811. Beijing: Science Press.
Zhuo, J., F. Wang, and T. Li. 2009. “Application of FRP strap in an innovative prestressed method.” J. Mater. Civ. Eng. 21 (4): 176–180. https://doi.org/10.1061/(ASCE)0899-1561(2009)21:4(176).
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Apr 11, 2018
Accepted: Oct 24, 2018
Published online: Mar 27, 2019
Published in print: Jun 1, 2019
Discussion open until: Aug 27, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.