In-Plane and Out-of-Plane Behavior of Masonry-Infilled RC Frames Strengthened with Fabric-Reinforced Cementitious Matrix
Publication: Journal of Composites for Construction
Volume 23, Issue 1
Abstract
In the present experimental study, six single-story, single-bay half-scale masonry-infilled reinforced concrete (RC) frames were tested to evaluate the performance of fabric-reinforced cementitious matrix (FRCM) strengthening under bidirectional loading. Five of these infilled RC frames were strengthened using different configurations, by varying the mode of fabric application, the presence of anchors, and the orientation of the fabric. Two methods of fabric application were employed in the present study: direct application and sandwich application. A unique loading protocol was used for the bidirectional loading of specimens which consisted of successive application of slow cyclic drifts for in-plane loading and shake table–generated ground motion for out-of-plane loading. The strengthened infills safely withstood story drifts of over 2.20%, preserving structural integrity without jeopardizing out-of-plane stability. The direct mode of fabric application exhibited superior performance with better bond characteristics and stress redistribution between the frame and infills. The mechanical anchors were effective in limiting the separation of infills from the frame, resulting in an enhanced bidirectional response. Orthogonal orientation of the fabric with respect to bed joints was more effective than oblique orientation.
Get full access to this article
View all available purchase options and get full access to this article.
References
ACI (American Concrete Institute). 2005. Acceptance criteria for moment frames based on structural testing and commentary. ACI 374.1. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2013. Design and construction guide of externally bonded FRCM systems for concrete and masonry repair and strengthening. ACI 549.4R. Farmington Hills, MI: ACI.
Aldea, C. M., B. Mobasher, and N. Jain. 2007. “Cement-based matrix-grid system for masonry rehabilitation.” In Vol. 244 of Proc., Textile Reinforced Concrete (TRC): German/Int. Experience Symp., 141–156. Farmington Hills, MI: ACI.
ASCE/SEI (Structural Engineering Institute). 2014. Seismic evaluation and retrofit of existing buildings. ASCE/SEI 41-13. Reston, VA: ASCE/SEI.
ASTM. 2013. Standard test method for tensile strength of concrete surfaces and the bond strength or tensile strength of concrete repair and overlay materials by direct tension (pull-off method). ASTM C1583. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard test method for compressive strength of masonry prisms. ASTM C1314. West Conshohocken, PA: ASTM.
Babaeidarabad, S., F. De Caso, and A. Nanni. 2014a. “Out-of-plane behavior of URM walls strengthened with fabric-reinforced cementitious matrix (FRCM) composite.” J. Compos. Constr. 18 (4): 04013057. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000457.
Babaeidarabad, S., F. De Caso, and A. Nanni. 2014b. “URM walls strengthened with fabric-reinforced cementitious matrix composite subjected to diagonal compression.” J. Compos. Constr. 18 (2): 04013045. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000441.
BIS (Bureau of Indian Standards). 1981. Indian standard code of practice for preparation and use of masonry mortars. IS 2250. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 1987. Indian standard code of practice for structural use of unreinforced masonry. IS 1905. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 1992a. Indian standard common burnt clay building bricks—Specification. IS 1077. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 1992b. Indian standard methods of test of burnt clay building bricks. Part 1: Determination of compressive strength. IS 3495. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2000. Indian standard plain and reinforced concrete: Code of Practice. IS 456. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2002. Indian standard criteria for earthquake resistant design of structure. Part 1: General provisions and buildings. IS 1893. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2007. Indian standard general construction in steel—Code of practice. IS 800. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2013a. Indian standard methods of tests for strength of concrete. IS 516. New Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2013b. Indian standard splitting tensile strength of concrete—Method of test. IS 5816. New Delhi, India: BIS.
Cries, T., J. Stuve, and T. Grundmann. 2008. “Textile reinforcement structures.” In Ceramic matrix composites: Fiber reinforced ceramics and their applications, 21–44. Weinheim, Germany: Wiley.
CSI (Computers and Structures, Inc.). 2008. CSI analysis reference manual. Vol. 15. Berkeley, CA: Computers and Structures, Inc.
Hegger, J., N. Will, and K. Rüberg. 2007. “Textile reinforced concrete—A new composite material.” In Advances in construction materials 2007, 147–156. Heidelberg, Germany: Springer.
Komaraneni, S., D. C. Rai, and V. Singhal. 2011. “Seismic behaviour of framed masonry panels with prior damage when subjected to out-of-plane loading.” Earthquake Spectra 27 (4): 1077–1103. https://doi.org/10.1193/1.3651624.
Koutas, L., S. N. Bousias, and T. C. Triantafillou. 2014a. “Seismic strengthening of masonry-infilled RC frames with TRM: Experimental study.” J. Compos. Constr. 19 (2): 04014048. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000507.
Koutas, L., A. Pitytzogia, T. C. Triantafillou, and S. N. Bousias. 2014b. “Strengthening of infilled reinforced concrete frames with TRM: Study on the development and testing of textile-based anchors.” J. Compos. Constr. 18 (3): A4013015. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000390.
Özkan, C., M. S. Ökten, M. Gençoğlu, and K. Güler. 2012. “Experimental investigation of infill walls strengthened by cementitious matrix-fabric composites.” In Proc., 15th World Conf. on Earthquake Engineering. Lisbon, Portugal: International Association for Earthquake Engineering.
Papanicolaou, C. G., T. C. Triantafillou, K. Karlos, and M. Papathanasiou. 2007. “Textile reinforced mortar (TRM) versus FRP as strengthening material of URM walls: In-plane cyclic loading.” Mater. Struct. 40 (10): 1081–1097. https://doi.org/10.1617/s11527-006-9207-8.
Papanicolaou, C. G., T. C. Triantafillou, M. Papathanasiou, and K. Karlos. 2008. “Textile reinforced mortar (TRM) versus FRP as strengthening material of URM walls: Out-of-plane cyclic loading.” Mater. Struct. 41 (1): 143–157. https://doi.org/10.1617/s11527-007-9226-0.
Parisi, F., A. Iovinella, A. Balsamo, N. Augenti, and A. Prota. 2013. “In-plane behavior of tuff masonry strengthened with inorganic matrix–grid composites.” Compos. Part B Eng. 45 (1): 1657–1666. https://doi.org/10.1016/j.compositesb.2012.09.068.
Prota, A., G. Marcari, G. Fabbrocino, G. Manfredi, and C. Aldea. 2006. “Experimental in-plane behavior of tuff masonry strengthened with cementitious matrix-grid composites.” J. Compos. Constr. 10 (3): 223–233. https://doi.org/10.1061/(ASCE)1090-0268(2006)10:3(223).
Rai, D. C., V. Singhal, S. Paikara, and D. Mukherjee. 2014. “Sub-paneling of masonry walls using precast reinforced concrete elements for earthquake resistance.” Earthquake Spectra 30 (2): 913–937. https://doi.org/10.1193/102010EQS178M.
Sagar, S. L., V. Singhal, D. C. Rai, and P. Gudur. 2017. “Diagonal shear and out-of-plane flexural strength of fabric-reinforced cementitious matrix-strengthened masonry walletes.” J. Compos. Constr. 21 (4): 04017016. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000796.
Singhal, V., and D. C. Rai. 2014a. “Role of toothing on in-plane and out-of-plane behavior of confined masonry walls.” J. Struct. Eng. 140 (9): 04014053. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000947.
Singhal, V., and D. C. Rai. 2014b. “Suitability of half-scale burnt clay bricks for shake table tests on masonry walls.” J. Mater. Civ. Eng. 26 (4): 644–657. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000861.
Tomaževič, M., M. Gams, and T. Berset. 2011. “Seismic strengthening of brick masonry walls with composites: An experimental study.” In Proc., 4th Structural Engineering World Congress, 307. Madrid, Spain: International Association for Shell and Spatial Structures.
Information & Authors
Information
Published In
Journal of Composites for Construction
Volume 23 • Issue 1 • February 2019
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jul 19, 2017
Accepted: Jul 3, 2018
Published online: Nov 21, 2018
Published in print: Feb 1, 2019
Discussion open until: Apr 21, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.