Various FRP-Bracing Configurations for Multistory Buildings under Seismic Loading: Conceptual Modeling and Comparative Assessment
Publication: Journal of Composites for Construction
Volume 21, Issue 3
Abstract
This paper presents the behavior of multistory buildings with fiber-reinforced polymer (FRP) brace members for new construction and for retrofit applications, including a comparative assessment against conventional steel brace systems. The El Centro earthquake load with a magnitude of 7.1 is employed to examine the performance of three brace types (hollow structural steel sections, and pultruded carbon FRP (CFRP) and glass FRP (GFRP) tubes for new buildings; and CFRP-confined and aramid FRP (AFRP)-confined concrete elements for existing buildings: seismic strengthening with FRP wrapping) and three shapes frequently used in practice (single-bay X-brace, super X-brace, and chevron brace). Nonlinear pushover and time-history models are developed to predict the seismic response of the retrofitted buildings with an emphasis on base shear force, ductility, mode shapes and frequencies, and strain energy. The brace materials and confinement schemes of the buildings control the effectiveness of the seismic-retrofit rather than the brace shapes. The FRP-braced buildings show strain energy characteristics comparable with those of the steel-braced buildings, although the ductility index of the latter is higher than the index of the former. The FRP-based braces reduce the maximum kinetic energy of the buildings up to 64% in comparison with the steel braces. However, the -delta effect is a concern when pultruded FRP tubes are used because of their low elastic modulus. The FRP-confined concrete braces are effective in terms of lowering the dynamic amplification of the buildings relative to their steel and pultruded FRP counterparts.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge financial support from the University of Colorado, Denver, and are indebted to anonymous reviewers for their insightful comments and practical suggestions. Proprietary information such as FRP product names was excluded in the paper to avoid commercialism.
References
ACI (American Concrete Institute). (2007). “Report on fiber-reinforced polymer (FRP) reinforcement for concrete structures.”, Farmington Hills, MI.
AISC. (2010). “Specification for structural steel buildings.” ANSI/AISC 360-10, Chicago.
ASCE. (2010). “Minimum design loads for buildings and other structures.” ASCE/SEI 7-10, Reston, VA.
ASCE. (2013). “Seismic rehabilitation of existing buildings.” ASCE 41-13, Reston, VA.
Attard, T. L., Abela, C. M., and Dhiradhamvit, K. (2011). “Seismic FRP retrofit of circular single-column bents using a ductility wrap envelop to alter failure modes.” Eng. Struct., 33(5), 1553–1564.
Bakis, C. E., et al. (2002). “Fiber-reinforced polymer composites for construction—State-of-the-art review.” J. Compos. Constr., 73–87.
Black, C. J., Makris, N., and Aiken, I. D. (2004). “Component testing, seismic evaluation and characterization of buckling-restrained braces.” J. Struct. Eng., 880–894.
Boscato, G., and Russo, S. (2009). “Free vibration of pultruded FRP elements: Mechanical characterization, analysis, and applications.” J. Compos. Constr., 13(6), 565–574.
CSI (Computers and Structures Inc.). (2013). CSI analysis reference manual, Berkeley, CA.
FEMA (Federal Emergency Management Agency). (2006). “Designing for earthquakes: A manual for architects.” Dept. of Homeland Security, Washington, DC.
GM Composites. (2015). Carbon: Pultruded carbon tubes, Mount Vernon, WA.
Han, L.-H., He, S.-H., and Liao, F.-Y. (2011). “Performance and calculations of concrete filled steel tubes (CFST) under axial tension.” J. Constr. Steel Res., 67, 1699–1709.
ICC (International Code Council). (2003). “International building code.” Birmingham, AL.
Lam, L., Teng, J. G., Cheung, C. H., and Xiao, Y. (2006). “FRP-confined concrete under axial cyclic compression.” Cem. Concr. Compos., 28(10), 949–958.
Moghaddam, H., and Hajirasouliha, I. (2006). “An investigation on the accuracy of pushover analysis for estimating the seismic deformation of braced steel frames.” J. Constr. Steel Res., 62(4), 343–351.
Nelson, M. S., et al. (2011). “Fiber-reinforced polymer stay-in-place structural forms for concrete bridge decks: State-of-the-art review.” ACI Struct. J., 111(5), 1069–1079.
Niroomandi, A., Maheri, A., Maheri, M. R., and Mahini, S. S. (2010). “Seismic performance of ordinary RC frames retrofitted at joints by FRP sheets.” Eng. Struct., 32(8), 2326–2336.
Ozbakkaloglu, T., and Akin, E. (2012). “Behavior of FRP-confined normal- and high-strength concrete under cyclic axial compression.” J. Compos. Constr., 451–463.
Ozbakkaloglu, T., Lim, J. C., and Vincent, T. (2013). “FRP-confined concrete in circular sections: Review and assessment of stress-strain models.” Eng. Struct., 49, 1068–1088.
Prager, W. (1955). “The theory of plasticity: A survey of recent achievements.” Proc., Inst. Mech. Eng., 169(1955), 41–57.
Prakash, V., Powell, G. H., and Filippou, F. C. (1992). “DRAIN-2DX: Base program user guide.”, Univ. of California, Berkeley, CA.
Qasrawi, Y., Heffernan, P. J., and Fam, A. (2015). “Performance of concrete-filled FRP tubes under field close-in blast loading.” J. Compos. Constr., .
SAP2000 version 14 [Computer software]. Computers and Structures, Berkeley, CA.
Song, J. (2010). “Dynamic characteristics of an FRP deck bridge.” M.S. thesis, Univ. of Tennessee, Knoxville, TN.
Strongwell. (2007). EXTREN fiberglass structural shapes: Design manual, Bristol, VA.
Teng, J. G., Lam, L., Lin, G., Lu, J. Y., and Xiao, Q. G. (2015). “Numerical simulation of FRP-jacketed RC columns subjected to cyclic and seismic loading.” J. Compos. Constr., .
Teng, J. G., Yu, T., and Fernando, D. (2012). “Strengthening of steel structures with fiber-reinforced polymer composites.” J. Constr. Steel Res., 78, 131–143.
UBC (Uniform Building Code). (1997). “Structural engineering design provisions.” Int. Conf. of Building Officials, Vol. 2, International Code Council, Washington, DC.
Zafar, A., and Andrawes, B. (2015). “Seismic behavior of SMA-FRP reinforced concrete frames under sequential seismic hazard.” Eng. Struct., 98, 163–173.
Information & Authors
Information
Published In
Copyright
©2016 American Society of Civil Engineers.
History
Received: Apr 23, 2016
Accepted: Aug 23, 2016
Published online: Oct 18, 2016
Discussion open until: Mar 18, 2017
Published in print: Jun 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.