Bond Performance of Basalt Fiber-Reinforced Polymer Bars to Concrete
Publication: Journal of Composites for Construction
Volume 19, Issue 3
Abstract
This paper presents the test results of a study on the bond behavior of basalt fiber-reinforced polymer (BFRP) bars to concrete. Thirty six concrete cylinders reinforced with BFRP bars and twelve cylinders reinforced with glass fiber-reinforced polymer (GFRP) bars were tested in direct pullout conditions. Test parameters included the FRP material (basalt and glass), the bar diameter, and the bar embedment length in concrete. Bond-slip curves of BFRP and GFRP bars revealed similar trends. BFRP bars developed average bond strength 75% of that of GFRP bars. All BFRP specimens failed in a pullout mode of failure along the interfacial surface between the outer layer of the bar and the subsequent core layers. The influence of various parameters on the overall bond performance of BFRP bars is analyzed and discussed. The well-known BPE and modified-BPE analytical models were calibrated to describe the bond-slip relationships of the bars. Test results demonstrate the promise of using the BFRP bars as an alternative to the GFRP bars in reinforcing concrete elements.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank Magmatech personnel for providing the BFRP bars needed for this study. Thanks are also extended to Pultrall personnel for donating the GFRP bars used in the tests.
References
Achillides, Z. (1998). “Bond behavior of FRP bars in concrete.” Ph.D. thesis, Centre for Cement and Concrete, Univ. of Sheffield, Sheffield, U.K.
Achillides, Z., and Pilakoutas, K. (2004). “Bond behavior of fiber reinforced polymer bars under direct pullout conditions.” J. Compos. Constr., 173–181.
Aiello, M. A., Leone, M., and Pecce, M. (2007). “Bond performances of FRP rebars-reinforced concrete.” J. Mater. Civ. Eng., 205–213.
Alvarez-Villarreal, A. (2004). “Temperature effect on bond properties of Fiber Reinforced Polymer (FRP) bars embedded in concrete.” M.Sc. thesis, Sherbrooke Univ, Sherbrooke, QC, Canada.
American Concrete Institute (ACI) Committee 440. (2006). “Guide for the design and construction of structural concrete reinforced with FRP bars.”, Farmington Hills, MI.
Arias, J. P. M., Vazquez, A., and Escobar, M. (2012). “Use of sand coating to improve bonding between GFRP bars and concrete.” J. Compos. Mater., 46(18), 2271–2278.
Baena, M., Torres, L., Turon, A., and Barris, C. (2009). “Experimental study of bond behavior between concrete and FRP bars using a pullout test.” Compos. Part B: Eng., 40(8), 784–797.
Bank, L. C., Puterman, M., and Katz, A. (1998). “The effect of material degradation on bond properties of fiber reinforced plastic reinforcing bars in concrete.” ACI Mater. J., 95(3), 232–243.
Benmokrane, B., Tighiouart, B., and Chaallal, O. (1996). “Bond strength and load distribution of composite GFRP reinforcing bars in concrete.” ACI Mater. J., 93(3), 246–253.
Boyle, H. C., and Karbhari, V. M. (1994). “Investigation of bond behavior between glass fiber composite reinforcements and concrete.” Polym. Plast. Technol. Eng., 33(6), 733–753.
Brik, V. B. (2003). “Advanced concept concrete using Basalt Fiber/BF composite bar reinforcement.”, Innovations Deserving Exploratory Analysis (IDEA) Programs, Transportation Research Board, Washington, DC.
Canadian Standards Association (CSA). (2002). “Design and construction of building components with fiber reinforced polymers.”, Mississauga, ON, Canada.
Carmignato, S., De Rosa, I. M., Sarasini, F., and Valente, M. (2009). “Characterisation of basalt fiber reinforced vinyl polyester composite: An overview.” Proc., 2nd Int. Conf. on Innovative Natural Fiber Composites for Industrial Applications, Univ. of Rome, Rome, Italy.
Cosenza, E., Manfredi, G., and Realfonzo, R. (1997). “Behavior and modeling of bond of FRP rebars to concrete.” J. Compos. Constr., 40–51.
Cosenza, E., Manfredi, G., and Realfonzo, R. (2002). “Development length of FRP straight rebars.” Compos. Part B: Eng., 33(7), 493–504.
Davalos, J. F., Chen, Y., and Ray, I. (2008). “Effect of FRP bar degradation on interface bond with high strength concrete.” Cem. Concr. Compos., 30(8), 722–730.
De Lorenzis, L., Rizzo, A., and La Tegola, A. (2002). “A modified pullout test for bond of near-surface mounted FRP rods in concrete.” Compos. Part B: Eng., 33(8), 589–603.
Ehsani, M. R., Saadatmanesh, H., and Tao, S. (1997). “Bond behavior of deformed GFRP rebars.” J. Compos. Mater., 31(14), 1413–1430.
Eligehausen, R., Popov, E. P., and Bertero, V. V. (1983). “Local bond stress-slip relationships of deformed bars under generalized excitations.”, Univ. of California, Berkeley, CA.
Hamad, B., Rteil, A., and Soudki, K. (2004). “Bond strength of tension lap splices in high-strength concrete beams strengthened with glass fiber reinforced polymer wraps.” J. Compos. Constr., 14–21.
Harajli, M., and Abouniaj, M. (2010). “Bond performance of GFRP bars in tension: Experimental evaluation and assessment of ACI 440 guidelines.” J. Compos. Constr., 659–668.
International Federation for Structural Concrete (Fib) report. (2000). “Bond of reinforcement in concrete, state-of-art report.” Bulletin 10, International Federation for Concrete Task Group Bond Models, Lausanne, Switzerland.
Liu, Q., Shaw, M., Parnas, R., and Mcdonnell, A. (2006). “Investigation of basalt fiber composite mechanical properties for applications in transportation.” Polym. Compos., 27(1), 41–48.
Lopresto, V., Leone, C., and De Iorio, I. (2011). “Mechanical characterization of basalt fiber reinforced plastic.” Compos. Part B, 42(4), 717–723.
Ludovico, M. D., Prota, A., and Manfredi, G. (2010). “Structural upgrade using basalt fibers for concrete confinement.” J. Compos. Constr., 541–552.
Militky, J., Kovacic, V., and Rubnerova, J. (2002). “Influence of thermal treatment on tensile failure of basalt fibers.” Eng. Fract. Mech., 69(9), 1025–1033.
Palmieri, A., Matthys, S., and Tierens, M. (2009). Basalt fibers: Mechanical properties and applications for concrete structures, Taylor and Francis, London, 165–169.
Parnas, R., Shaw, M., and Liu, Q. (2007). “Basalt fiber reinforced polymer composites.”, Institute of Materials Science, Univ. of Connecticut, Mansfield, CT.
Ramakrishnan, V., Neeraj, S., and Brik, V. (1998). “Performance evaluation of 3-D basalt fiber reinforced concrete and basalt rod reinforced concrete.”, Transportation Research Board, National Research Council, Washington, DC.
Sayed, A. F., Foret, G., and Le Roy, R. (2011). “Bond between carbon fiber-reinforced polymer (CFRP) bars and ultra high performance fiber reinforced concrete (UHPFRC): Experimental study.” Constr. Build. Mater., 25(2), 479–485.
Sim, J., Park, C., and Moon, D. Y. (2005). “Characteristic of basalt fiber as a strengthening material for concrete structures.” Compos. Part B, 36(6), 504–512.
Tastani, S. P., and Pantazopoulou, S. J. (2006). “Bond of GFRP bars in concrete: Experimental study and analytical interpretation.” J. Compos. Constr., 381–391.
Tepfers, R., Hedlund, G., and Rosinski, B. (1998). “Pull-out and tensile reinforcement splice tests with GFRP bars.” Proc., 2nd Int. Conf. on Composites in Infrastructure, H. Saadatmanesh and M. R. Ehsani, eds., International Conference on Composites in Infrastructure (ICCI), Tucson, AZ.
Tighiouart, B., Benmokrane, B., and Gao, D. (1998). “Investigation of bond in concrete member with fiber reinforced polymer (FRP) bars.” Constr. Build. Mater., 12(8), 453–462.
Wang, H., and Belarbi, A. (2010). “Static and fatigue bond characteristics of FRP rebars embedded in fiber-reinforced concrete.” J. Compos. Mater., 44(13), 1605–1622.
Wei, B., Cao, H., and Song, S. (2010). “Tensile behavior contrast of basalt and glass fibers after chemical treatment.” Mater. Des., 31(9), 4244–4250.
Wei, B., Cao, H., and Song, S. (2011). “Degradation of basalt fiber and glass fiber/epoxy resin composites in seawater.” Corros. Sci., 53(1), 426–431.
Wu, Z., Wang, X., Iwashita, K., Sasaki, T., and Hamaguchi, Y. (2010). “Tensile fatigue behavior of FRP and hybrid FRP sheets.” Compos. Part B, 41(5), 396–402.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Oct 18, 2013
Accepted: Mar 12, 2014
Published online: Aug 11, 2014
Discussion open until: Jan 11, 2015
Published in print: Jun 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.