FRP Slab Capacity Using Yield Line Theory
Publication: Journal of Composites for Construction
Volume 18, Issue 6
Abstract
Fiber reinforced polymer (FRP) bars have been increasingly used in bridge deck slabs over the last decades to overcome corrosion issues. However, there is still a critical need for a rational method to analyze the load capacity of such bridge deck slabs. Because FRP bars possess a linear stress-strain relationship, the moment-curvature response of FRP concrete section, either reinforced or prestressed, does not exhibit a distinct yield-plateau, thus it is unclear if conventional yield line theory is applicable. Therefore, the concept of an equivalent plastic moment capacity for FRP concrete sections is introduced and applied in yield line theory for bridge deck slabs. A full-scale bridge deck slab with precast panels reinforced and prestressed with aramid fiber reinforced polymer (AFRP) bars is experimentally tested under different wheel and axle load configurations on either interior spans or overhangs. The results confirm the high accuracy of the failure analysis using the yield line theory, where the load capacity predictions are within 3% accuracy of the experimentally observed results.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by a grant from the National Science Foundation (NSF 0927333). The authors would like to express appreciation for the generous support from NSF to conduct this research. The findings and opinions presented in this paper are those of the authors and are not necessarily those of the sponsoring agency.
References
AASHTO LRFD. (2010). Bridge design specification, 5th Ed., Washington, DC.
ASTM. (2008). “Standard test method for compressive strength of cylindrical concrete specimens.” C39, West Conshohocken, PA.
British Standards Institution (BSI). (2002). “Eurocode 2: Design of concrete structures-part 1: General rules and rules for buildings.” prEN 1992-1-1 (draft for stage 49), London.
Dulude, C., Ahmed, E., El-Gamal, S., and Benmokrane, B. (2010). “Testing of large-scale two-way concrete slabs reinforced with GFRP bars.” 5th Int. Conf. on FRP Composites in Civil Engineering (CICE), Beijing, China, 4.
Ehsani, M. R., Saadatmanesh, H., and Nelson, C. T. (1997). “Transfer and flexural bond performance of aramid and carbon frp bars.” PCI J., 42(1), 76–86.
El-Ghandour, A. W., Pilaoutas, K., and Waldron, P. (2003). “Punching shear behavior of fiber reinforced polymer reinforced concrete flat slabs: Experimental study.” J. Compos. Constr., 258–265.
Hassan, T., Abdelrahman, A., Tadros, G., and Rizkalla, S. (2000). “Fibre reinforced polymer reinforcing bars for bridge decks.” Can. J. Civ. Eng., 27(5), 839–849.
Hornbeck, R. W. (1982). Numerical methods, Prentice Hall, New York.
Lee, J. H., Yoon, Y. S., and Mitchell, D. (2009). “Improving punching shear behavior of glass fiber-reinforced polymer reinforced slabs.” ACI Struct. J., 106(4), 427–434.
Mander, T. J., Mander, J. B., and Head, M. H. (2011a). “Compound shear-flexural capacity of reinforced concrete-topped precast prestressed bridge decks.” J. Bridge Eng., 4–11.
Mander, T. J., Mander, J. B., and Head, M. H. (2011b). “Modified yield line theory for full-depth precast concrete bridge deck overhang panels.” J. Bridge Eng., 12–20.
Matthys, S., and Taerwe, L. (2000a). “Concrete slabs reinforced with FRP grids. I. One-way bending.” J. Compos. Constr., 145–153.
Matthys, S., and Taerwe, L. (2000b). “Concrete slabs reinforced with FRP grids. II. Punching resistance.” J. Compos. Constr., 154–161.
Medina, J. C. (2011). “Characteristics of AFRP bars for prestressing applications.” M.S. thesis, Texas A&M Univ., College Station, TX.
Michaluk, C. R., Rizkalla, S. H., Tadros, G., and Benmokrane, B. (1998). “Flexural behavior of one-way concrete slabs reinforced by fiber reinforced plastic reinforcement.” ACI Struct. J., 95(3), 353–365.
Nielsen, M. P. (1999). Limit analysis and concrete plasticity, 2nd Ed., Wiley, New York.
Ospina, C. E., Alexander, S. D. B., and Roger Cheng, J. J. (2003). “Punching of two-way concrete slabs with fiber-reinforced polymer reinforcing bars or grids.” ACI Struct. J., 100(5), 589–598.
Park, R., and Gamble, W. L. (2000). Reinforced concrete slabs, 2nd Ed., Wiley, New York.
Pirayeh Gar, S. (2012). “Structural performance of a full-depth precast bridge deck system prestressed and reinforced with AFRP bars.” Ph.D. dissertation, Texas A&M Univ., College Station, TX.
Pirayeh Gar, S., Head, M., and Hurlebaus, S. (2012). “Discussion on tension stiffening in prestressed concrete beams using moment-curvature relationship.” J. Struct. Eng., 1075–1078.
Pirayeh Gar, S., Head, M., Hurlebaus, S., and Mander, J. (2013a). “Comparative experimental performance of bridge deck slabs with AFRP and steel precast panels.” J. Compos. Constr., 04013014.
Pirayeh Gar, S., Head, M., Hurlebaus, S., and Mander, J. (2013b). “Experimental performance of AFRP concrete bridge deck slab with full-depth precast prestressed panels.” J. Bridge Eng., 04013018.
Rahman, A. H., Kingsley, C. Y., and Kobayashi, K. (2000). “Service and ultimate load behavior of bridge deck reinforcement with carbon FRP grid.” J. Compos. Constr., 16–23.
Salakawy, E. F. El., and Benmokrane, B. (2004). “Serviceability of concrete bridge deck slabs reinforced with fiber-reinforced polymer composite bars.” ACI Struct. J., 101(5), 727–736.
Standards New Zealand. (2004). “Concrete structures standard.” NZS 3101, Wellington, New Zealand.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Sep 26, 2013
Accepted: Jan 31, 2014
Published online: Mar 17, 2014
Discussion open until: Aug 17, 2014
Published in print: Dec 1, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.