Bond Strength of Lap-Spliced GFRP Bars in Concrete Beams
Publication: Journal of Composites for Construction
Volume 17, Issue 3
Abstract
In this paper, the bond strength of lap-spliced glass fiber–reinforced polymer (GFRP) bars in concrete beams is experimentally investigated. Thirteen beam specimens were manufactured for laboratory experiments. The parameter of transverse reinforcement along the splice length was selected as the main variable for the beam specimens. Other variables were surface properties of GFRP bars, bar diameter, and concrete compressive strength. Test results show that the effect of transverse reinforcement on bond strength between GFRP bars and concrete depends on the surface properties of reinforcing bars. The experimental results obtained in the present study and the results reported in the literature are compared with the current design equation provided by the American Concrete Institute (ACI) Committee 440 guidelines. The equation of ACI Committee 440 for evaluating the bond strength of GFRP bars underestimates the bond strength of spliced GFRP bars confined with large amounts of transverse reinforcement. For cases of small values of transverse reinforcement and splices without transverse reinforcement, the equation of ACI Committee 440 is unconservative and overestimates the bond strength. In this paper, an equation for predicting the bond strength of GFRP bars is also proposed on the basis of test results and the Monte Carlo simulation method.
Get full access to this article
View all available purchase options and get full access to this article.
References
Aly, R. (2007). “Stress along tensile lap-spliced fiber reinforced polymer reinforcing bars in concrete.” Can. J. Civ. Eng., 34(9), 1149–1158.
Aly, R. S. M. (2005). “Experimental and analytical studies on bond behavior of tensile lap spliced FRP reinforcing bars in concrete.” Ph.D. thesis, Univ. of Sherbrooke, Sherbrooke, Quebec, QC.
American Concrete Institute (ACI) Committee 440. (2006). “Guide for the design and construction of structural concrete reinforced with FRP bars.”, Farmington Hills, MI.
Banea, M., Torres, L., Turon, A., and Barris, C. (2009). “Experimental study of bond behavior between concrete and FRP bars using a pull-out test.” Composites, Part B, 40(8), 784–797.
Canadian Standard Association (CSA). (2002). “Design and construction of building components with fiber reinforced polymer.”, Rexdale, ON.
Darwin, D., Idun, E. K., Zou, J., and Tholen, M. L. (1998). “Reliability based strength reduction factor for bond.” ACI Struct. J., 95(4), 434–443.
Darwin, D., Zou, J., Tholen, M., and Idun, E. (1996). “Development length criteria for conventional and high relative rib area reinforcing bars.” ACI Struct. J., 93(3), 347–359.
Esfahani, M. R., Kianoush, M. R., and Lachemi, M. (2005). “Bond strength of glass fiber reinforced polymer reinforcing bars in normal and self consolidating concrete.” Can. J. Civ. Eng., 32, 553–560.
Hao, Q. D., Wang, B., and Ou, J. P. (2006). “Fibre reinforced polymer rebar’s application to civil engineering.” Concrete, 9, 38–40.
Harajli, M., and Abouniaj, M. (2010). “Bond performance of GFRP bars in tension: experimental evaluation and assessment of ACI 440 guidelines.” J. Compos. Constr., 14(6), 659–668.
He, Z., and Tian, G. (2011). “Reliability based bond design for GFRP-reinforced concrete.” Mater. Struct., 44(8), 1477–1489.
Lee, J. O., Yang, Y. S., and Ruy, W. S. (2002). “A comparative study on reliability index and target performance based probabilistic structural design optimization.” Comp. Struct., 80(3–4), 257–269.
Mosley, C. P., Tureyen, A. K., and Frosch, R. J. (2008). “Bond strength of nonmetallic reinforcing bars.” ACI Struct. J., 105(5), 634–642.
Orangun, C. O., Jirsa, J. O., and Breen, J. E. (1977). “Reevaluation of test data on development length and splices.” Proc. Am. Concr. Inst., 74(3), 114–122.
Tighiouart, B., Benmokrane, B., and Gao, D. (1998). “Investigation of bond in concrete member with fibre reinforced polymer (FRP) bars.” Constr. Build. Mater., 12(8), 453–462.
Tighiouart, B., Benmokrane, B., and Mukhopadhyaya, P. (1999). “Bond strength of glass FRP rebar splices in beams under static loading.” Constr. Build. Mater., 13(7), 383–392.
Val, D. V., and Chernin, L. (2009). “Serviceability reliability of reinforced concrete beams with corroded reinforcement.” J. Struct. Eng., 135(8), 896–905.
Wambeke, B., and Shield, C. (2006). “Development length of glass fiber reinforced polymer bars in concrete.” ACI Struct. J., 103(1), 11–17.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Mar 9, 2012
Accepted: Jan 2, 2013
Published online: Jan 4, 2013
Published in print: Jun 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.