Oxygen Permeability of FRP-Concrete Repair Systems
Publication: Journal of Composites for Construction
Volume 16, Issue 3
Abstract
Fiber reinforced polymers (FRP) are increasingly used for repairing corrosion-damaged concrete structures. The performance of the repairs is critically dependent on the oxygen permeability of the FRP-concrete system. This paper presents the results of an experimental study in which the oxygen permeation of concrete and FRP-concrete systems were determined. In the study, concrete specimens with three different water-cementitious ratios were initially tested. Subsequently, uni directional one and two-layer carbon and fiberglass material were bonded to the concrete surface, and the oxygen permeation of the FRP-concrete systems were determined. The results showed a significant reduction in the oxygen permeation of concrete after FRP had been bonded. The best performance was obtained for FRP bonded to concrete with the highest water-cementitious ratio. An expression for the equivalent thickness of FRP-concrete systems was derived by using Fick’s law. This facilitates the evaluation of the effectiveness of alternate FRP-concrete corrosion repair schemes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This material is based upon work supported by the National Science Foundation under Grant No. CMS-0409401. Matthew Durshimer helped with the experimental work.
References
ASTM. (2002). “Standard test method for oxygen transmission rate through dry packages using a coulometric sensor.” F1307, West Conshohocken, PA.
ASTM. (2005). “Standard test method for oxygen gas transmission rate through plastic film and sheeting using a coulometric sensor.” D3985, West Conshohocken, PA.
ASTM. (2008). “Standard practice for preparing concrete floors to receive resilient flooring.” F710, West Conshohocken, PA.
Bertolini, L., Elsener, B., Pedeferri, P., and Polder, R. (2004). Corrosion of steel in concrete, Wiley-VCN Verlag, Weinheim, Germany.
Crank, J. (1968). Diffusion in polymers, Academic, New York.
Crank, J. (1975). The mathematics of diffusion, 2nd Ed., Brunel Univ., Oxford Univ.,Uxbridge, UK.
Figaro. (2004). Technical informaion for KE-Series, Glenview, IL.
Florida Dept. of Transportation (FDOT). (2010). Standard specifications for road and bridge construction, Tallahassee, FL.
Gjorv, O. E., Vennesland, O., and El-Busaidy, A. H. S. (1987). “Diffusion of dissolved oxygen through concrete.” Mater. Perform.MTPFBI, 25(12), 39–44.
Kessler, R., Powers, R., and Lasa, I. (2006). “Case studies of impressed current cathodic protection systems for marine reinforced concrete structures in Florida.” Corrosion NACE 2006, Paper No. 06330.
Khan, M. I. (2003). “Permeation of high performance concrete.” J. Mater. Civ. Eng.JMCEE7, 15(1), 84–92.
Khoe, C. (2011). “Oxygen diffusion characterization of FRP composites used in concrete repair and rehabilitation.” Ph.D., thesis, Dept. of Civil and Environmental Engineering, Univ. of South Florida, Tampa, FL.
Khoe, C., Chowdhury, S., Bhethanabotla, V., and Sen, R. (2010). “Measurement of oxygen permeability of epoxy polymers.” ACI Mater. J.AMAJEF, 107(2), 138–146.
Khoe, C., Sen, R., and Bhethanabotla, V. (2011a). “Characterization of FRP as an oxygen barrier.” ACI SP-275-18, ACI, Farmington Hills, MI.
Khoe, C., Sen, R., and Bhethanabotla, V. (2011b). “Oxygen permeability of fiber reinforced polymers.” J. Compos. Constr.JCCOF2, 15(4), 513–521.
Kobayashi, K., and Shuttoh, K. (1991). “Oxygen diffusivity of various cementitious materials.” Cem. Concr. Res.CCNRAI, 21(2–3), 273–284.
Lawrence, C. D. (1984). “Transport of oxygen through concrete.” Proceedings British Ceramic Society, Vol. 35, 277–293.
Paul, D. R. (1965). “The properties of amorphous high polymers.” Ph.D. thesis, Univ. of Wisconsin, Madison, WI.
Tittarelli, F. (2009). “Oxygen diffusion through hydrophobic cement-based materials.” Cem. Concr. Res.CCNRAI, 39(10), 924–928.
Trefry, M. (2001). “An experimental determination of the effective oxygen diffusion coefficient for a high density polypropylene geomembrane.” Technical Rep. 37/01, CSIRO.
Information & Authors
Information
Published In
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Apr 7, 2011
Accepted: Sep 21, 2011
Published online: Sep 23, 2011
Published in print: Jun 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.