Bond Performance of GFRP Bars in Tension: Experimental Evaluation and Assessment of ACI 440 Guidelines
Publication: Journal of Composites for Construction
Volume 14, Issue 6
Abstract
The development/splice strength and the pullout local bond stress-slip response of glass fiber-reinforced polymer (GFRP) bars in tension were experimentally investigated using beam specimens and pullout specimens, respectively. Two types of 12-mm (0.47-in.)-diameter GFRP bars were evaluated, namely, thread wrapped and ribbed. The test parameters included the concrete cover, the splice length, and the area of steel confinement for the beam specimens, and the concrete compressive strength for the pullout specimens. Companion steel reinforced beams were also tested for comparison. All beam specimens reinforced with thread-wrapped GFRP bars experienced pullout mode of bond failure, while all specimens reinforced with ribbed GFRP bars or steel bars experienced splitting mode of bond failure. It was found that the bond strength of FRP bars is largely dependent on the surface conditions of the bars. The pullout local bond stress-slip response of ribbed GFRP bars is intrinsically similar to that of steel bars reported in the literature. The bond strength of both types of GFRP bars investigated was about two to three times lower than that of steel bars. Predictions of the development/splice strength of GFRP bars in accordance with the ACI Committee 440 guidelines were unconservative in comparison with the test data. Also, in contradiction with the current ACI 440 report, the use of transverse confining reinforcement increased the bond strength by a sizable 15–30%.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by the Lebanese National Council for Scientific Research and the University Research Board of the American University of Beirut (AUB). The writers are grateful for that support and to the Faculty of Engineering and Architecture at AUB for providing the test facilities.UNSPECIFIEDUNSPECIFIED
References
Aiello, M. A., Leone, M., and Pecce, M. (2002). “Influence of surface treatment on bond between FRP rebars and concrete.” Proc., 3rd Int. Symp. “Bond in Concrete—From Research to Standards”, G. Balazs, M. Bartos, J. Caims, and A. Borosnyoi, eds., Budapest Univ. of Technology and Economics, Budapest, 667–674.
Aly, R., Benmokrane, B., and Ebead, U. (2006). “Tensile lap splicing of fiber-reinforced polymer reinforcing bars in concrete.” ACI Struct. J., 103(6), 857–864.
American Concrete Institute (ACI). (2006). “Guide for the design and construction of structural concrete reinforced with FRP bars.” ACI 440.1R-06, Detroit.
Azizinamini, A., Stark, M., Roller, J., and Ghosh, S. (1993). “Bond performance of reinforcing bars embedded in high-strength concrete.” ACI Struct. J., 90(5), 554–561.
Balazs, G., Bartos, M., Caims, J., and Borosnyoi, A., eds. (2002). “Bond in concrete—From research to standards.” Proc., 3rd Int. Symp., Budapest Univ. of Technology and Economics, Budapest.
Canadian Standard Association (CAN/CSA). (2002). “Design and construction of building components with fibre reinforced polymers.” S806-02, Rexdale, Ont.
Darwin, D., Lutz, L. A., and Zuo, J. (2005). “Recommended provisions and commentary on development and lap splice lengths for deformed reinforcing bars in tension.” ACI Struct. J., 102(6), 892–900.
Ehsani, M. R., Saadetmanesh, H., and Tao, S. (1996). “Design recommendation for bond of GFRP bars to concrete.” J. Struct. Eng., 122(3), 247–257.
Eligehausen, R., Popov, E. P., and Bertero, V. V. (1983). “Local bond stress-slip relationships of deformed bars under generalized excitations.” Rep. No. UCB/EERC-83/23, Univ. of California, Berkeley, Calif.
Gao, D., Benmokrane, B., and Tighiouart, B. (1998). “Bond properties of FRP rebars to concrete.” Technical Rep., Dept. of Civil Eng., Univ. of Sherbrooke, Quebec.
Harajli, M. H. (2004). “Comparison of bond strength of reinforcing bars in normal and high-strength concrete.” J. Mater. Civ. Eng., 16(4), 365–374.
Harajli, M. H., Hout, M., and Jalkh, W. (1995). “Local bond stress-slip relationship of reinforcing bars embedded in fiber reinforced concrete.” ACI Mater. J., 92(4), 343–354.
Orangun, C. O., Jirsa, J. O., and Breen, J. E. (1977). “Reevaluation of test data on development length and splices.” ACI Struct. J., Proceedings, 74(3), 114–122.
Tepfers, R. (2002). “Test system for evaluation of bond properties of FRP reinforcement in concrete.” Proc., 3rd Int. Symp. “Bond in Concrete—From Research to Standards”, G. Balazs, M. Bartos, J. Caims, and A. Borosnyoi, eds., Budapest Univ. of Technology and Economics, Budapest, 657–666.
Wambeke, B., and Shield, C. (2006). “Development length of glass fiber reinforced polymer bars in concrete.” ACI Struct. J., 103(1), 11–17.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: Jul 13, 2009
Accepted: Apr 29, 2010
Published online: May 7, 2010
Published in print: Dec 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.