Flexural Behavior and Ultimate Capacity of Adjacent Box Girders with Expansion Joint in the Parapet
Publication: Journal of Bridge Engineering
Volume 27, Issue 8
Abstract
The incorporation of expansion joints in the parapet wall of bridge girders is standard practice to account for factors such as temperature differentials, shrinkage, and settlement. Gaining an understanding of the influence of expansion joints in bridge parapets is important, since the overall service performance and integrity of the bridge can be significantly influenced by the presence of expansion joints in parapets. This study investigated the flexural behavior of the bridge girder considering the effects of the expansion joint through experimental testing and numerical analyses. Effects of the expansion joint on flexural stresses and on the migration of the neutral axis of the exterior girder were investigated. Both the cracking pattern of the girders subjected to pure flexure and the ultimate flexural capacity were also examined. Compared with the benchmark specimen without the parapet and expansion joint, it was found that the plane cross section assumption cannot be applied to the cross section at the expansion joint. The stress distribution across the section height is nonlinear, with amplified compressive stresses at the top and lower tensile stresses at the bottom than for the benchmark girders. Diagonal cracks occurred and propagated toward the expansion joint at the pure flexure region. Though the flexural capacity of the single girder was slightly increased, the actual load-carrying capacity of the serviced exterior box girder with the expansion joint was substantially decreased.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Authors acknowledge support for this study provided by the National Natural Science Foundation of China (Nos. 51978622 and 51908504) and the Natural Science Foundation of Zhejiang Province (No. LY21E080017).
References
ACI (American Concrete Institute). 2014. Building code requirements for structural concrete (ACI 318-14) and commentary on building code requirements for structural concrete (ACI 318R-14). Farmington Hills, MI: ACI.
Azimi, H., and K. Sennah. 2015. “Parametric effects on evaluation of an impact-damaged prestressed concrete bridge girder repaired by externally bonded carbon-fiber-reinforced polymer sheets.” J. Perform. Constr. Facil 29 (6): 04014147. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000544.
Barbieri, D. M., Y. Chen, E. Mazzarolo, B. Briseghella, and A. M. Tarantino. 2018. “Longitudinal joint performance of a concrete hollow core slab bridge.” Transp. Res. Rec. 2672 (41): 196–206. https://doi.org/10.1177/0361198118781653.
Barker, M. G. 2001. “Quantifying field-test behavior for rating steel girder bridges.” J. Bridge Eng. 6 (4): 254–261. https://doi.org/10.1061/(ASCE)1084-0702(2001)6:4(254).
Bartsch, H., F. Eyben, G. Pauli, S. Schaffrath, and M. Feldmann. 2021. “Experimental and numerical investigations on the rotation capacity of high-strength steel beams.” J. Struct. Eng. 147 (6): 04021067. https://doi.org/10.1061/(ASCE)ST.1943-541X.0003038.
Brunesi, E., D. Bolognini, and R. Nascimbene. 2015. “Evaluation of the shear capacity of precast-prestressed hollow core slabs: Numerical and experimental comparisons.” Mater. Struct. 48 (5): 1503–1521. https://doi.org/10.1617/s11527-014-0250-6.
Campione, G. 2012. “Flexural behavior of steel fibrous reinforced concrete deep beams.” J. Struct. Eng. 138 (2): 235–246. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000442.
Campione, G. 2017. “Flexural behavior of glass beams with T and I shape cross sections.” J. Struct. Eng. 143 (9): 04017111. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001836.
Carreira, D., J., and K. H. Chu. 1985. “Stress-strain relationship for plain concrete in compression.” J. Am. Concr. Inst. 82 (6): 797–804.
Conner, S., and X. S. Huo. 2006. “Influence of parapets and aspect ratio on live-load distribution.” J. Bridge Eng. 11 (2): 188–196. https://doi.org/10.1061/(ASCE)1084-0702(2006)11:2(188).
Di, J., Y. Sun, K. Yu, L. Liu, and F. Qin. 2020. “Experimental investigation of shear performance of existing PC hollow slab.” Eng. Struct. 211: 110451. https://doi.org/10.1016/j.engstruct.2020.110451.
Eamon, C. D., and A. S. Nowak. 2002. “Effects of edge-stiffening elements and diaphragms on bridge resistance and load distribution.” J. Bridge Eng. 7 (5): 258–266. https://doi.org/10.1061/(ASCE)1084-0702(2002)7:5(258).
Girhammar, U. A., and M. Pajari. 2008. “Tests and analysis on shear strength of composite slabs of hollow core units and concrete topping.” Constr. Build. Mater. 22 (8): 1708–1722. https://doi.org/10.1016/j.conbuildmat.2007.05.013.
Guan, P., Z. Xu, and B. Wang. 2002. “Shear capacity analysis methods on RC members.” World Earthquake Eng. 18: 95–101.
Harries, K. A. 2009. “Structural testing of prestressed concrete girders from the lake view drive bridge.” J. Bridge Eng. 14 (2): 78–92. https://doi.org/10.1061/(ASCE)1084-0702(2009)14:2(78).
He, W., R. He, and S. Zhao. 2011. “Analysis of integral loading properties of assembled prestressed concrete hollow slab bridge affected by hinge concrete.” In Design, Construction, Rehabilitation, and Maintenance of Bridges, Geotechnical Special Publication 219, edited by P. Moyo, P. Ooi, E. Zhai, and J. Myers, 144–150. Reston, VA: ASCE.
Li, C., D. Yang, W. Peng, and H. Liu. 2021. “Influence of expansion joints in deck parapets on localized cracking in adjacent box girders.” J. Bridge Eng. 26 (3): 04021002. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001688.
Li, X., G. Wu, M. S. Popal, and J. Jiang. 2018. “Experimental and numerical study of hollow core slabs strengthened with mounted steel bars and prestressed steel wire ropes.” Constr. Build. Mater. 188: 456–469. https://doi.org/10.1016/j.conbuildmat.2018.08.073.
Lin, W., T. Yoda, and N. Taniguchi. 2016. “Effects of bridge accessories in steel–concrete composite railway bridges in service condition.” J. Bridge Eng. 21 (2): 04015050. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000809.
Park, M. K., D. H. Lee, S. Han, and K. S. Kim. 2019. “Web-shear capacity of thick precast prestressed hollow-core slab units produced by extrusion method.” Int. J. Concr. Struct. Mater. 13 (1): 7. https://doi.org/10.1186/s40069-018-0288-x.
Rahman, M. K., M. H. Baluch, M. K. Said, and M. A. Shazali. 2012. “Flexural and shear strength of prestressed precast hollow-core slabs.” Arab. J. Sci. Eng. 37 (2): 443–455. https://doi.org/10.1007/s13369-012-0175-8.
Ramirez, J., and J. Breen. 1991. “Evaluation of a modified truss model approach for beams in shear-closure.” ACI Struct. J. 88 (5): 562–571.
Wei, J., P. Li, Y. Xu, R. Dong, and Z. Yu. 2011. “Influencing factor analysis on coordinated working performance of hinge joint in hollow slab.” [In Chinese.] China J. Highway Transp. 24 (2): 29–33. http://zgglxb.chd.edu.cn/CN/Y2011/V24/I2/29.
Yang, B., M. Dong, Q. Han, M. Elchalakani, and G. Xiong. 2021. “Flexural behavior and rotation capacity of welded I-beams made from 690-MPa high-strength steel.” J. Struct. Eng. 147 (2): 04020320. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002871.
Ye, J., J. Liu, B. Yu, and Y. Fu. 2013. “Experiment on shear property of hinge joints of concrete hollow slab.” [In Chinese.] J. Highway Transp. Res. Dev. 30 (6): 33–39. http://www.gljtkj.com/CN/10.3969%20/j.issn.1002-0268.2013.06.007.
Zararis, P. D. 2003. “Shear compression failure in reinforced concrete deep beams.” J. Struct. Eng. 129 (4): 544–553. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:4(544).
Zhang, Q., D. Jia, Y. Bao, S. Dong, Z. Cheng, and Y. Bu. 2019. “Flexural behavior of steel–concrete composite beams considering interlayer slip.” J. Struct. Eng. 145 (9): 04019084. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002374.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Sep 21, 2021
Accepted: Apr 18, 2022
Published online: Jun 15, 2022
Published in print: Aug 1, 2022
Discussion open until: Nov 15, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.