Cross-Sectional Moment Capacity Prediction of Steel Box Girders Based on the CSM
Publication: Journal of Bridge Engineering
Volume 27, Issue 7
Abstract
The objective of this paper is to propose the prediction method of the cross-sectional moment capacity for continuous steel box girder bridges based on the continuous strength method (CSM). First, the critical buckling strain of the compressed members in box girders is determined using the base curve in the CSM, with which the elastoplastic cross-sectional analysis is conducted to derive the ultimate bending moment of steel box girders under sagging and hogging bending states. Then, a large number of applicable cross sections of steel box girders are designed, and their cross-sectional moment capacities based on the CSM and the elastic and plastic analyzing methods are calculated. Based on an analysis of the mutual relationship of these three moment capacities, the linear and quadratic prediction equations are proposed for both the positive and the negative moment capacities of steel box cross sections. The proposed equations are adopted to predict the cross-sectional bending capacities of some steel box girders in experiments, and the predicting results agree well with the experimental ones. Lastly, the proposed equations are applied to predict the cross-sectional moment capacities of the main girder in Xiamen Second East Passage as a case study. Compared with their elastic moment capacities, the analysis results show that using the proposed linear prediction equations, the cross-sectional moment capacities presented a 5.2% increase for cross sections with a nominal width-to-thickness ratio of 39.2 at support and a 22.2% increase for cross sections with a nominal width-to-thickness ratio of 37.6 at midspan. The linear and quadratic interpolation equations can well predict the cross-sectional moment capacity of the steel box girder.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. 2017. LRFD bridge design specification. Washington, DC: AASHTO.
Afshan, S., and L. Gardner. 2013. “The continuous strength method for structural stainless steel design.” Thin-Walled Struct. 68: 42–49. https://doi.org/10.1016/j.tws.2013.02.011.
Bai, L., R. Shen, L. Wang, Y. Wang, and R. Miao. 2018. “Experimental and numerical study on buckling behavior of a rigidly stiffened plate with tee ribs.” Int. J. Steel Struct. 18 (2): 1–14.
CEN (European Committee for Standardization). 2005. Design of steel structures—Part 1–1: General rules and rules for buildings. Eurocode 3. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2006a. Design of steel structures—Part 1-5: Plated structural elements. Eurocode 3. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2006b. Design of steel structures—Part 2: Steel bridges. Eurocode 3. Brussels, Belgium: CEN.
Chen, S.-J., and K.-C. Yang. 2002. “Inelastic behavior of orthotropic steel deck stiffened by U-shaped stiffeners.” Thin-Walled Struct. 40 (6): 537–553. https://doi.org/10.1016/S0263-8231(02)00005-8.
Chou, C. C., C. M. Uang, and F. Seible. 2006. “Experimental evaluation of compressive behavior of orthotropic steel plates for the New San Francisco-Oakland bay bridge.” J. Bridge Eng. 11 (2): 140–150. https://doi.org/10.1061/(ASCE)1084-0702(2006)11:2(140).
Di, J., X. Zhou, Z. Lu, P. Qiao, and L. Ning. 2009. “Experiment on ultimate bearing capacity of U-stiffened plate of orthotropic steel box girder.” [In Chinese.] China J. Highway Transport 22 (2): 59–64.
Ferreira, P. S., and F. Virtuoso. 2015. “Stiffened flanges used in steel box girder bridges.” In Proc., Int. Conference on Multi-Span Large Bridges, 1163–1168. CRC Press.
Foster, A. S. J., and L. Gardner. 2016. “Stability of steel beams using the continuous strength method.” Thin-Walled Struct. 100: 1–13. https://doi.org/10.1016/j.tws.2015.11.018.
Gardner, L. 2008. “The continuous strength method.” Proc. Inst. Civ. Eng. Struct. Build. 161 (3): 127–133. https://doi.org/10.1680/stbu.2008.161.3.127.
Gardner, L., and D. A. Nethercot. 2004. “Structural stainless steel design: A new approach.” Struct. Eng. 82: 21–28.
GB (Guobiao Standard). 2015. Specifications for design of highway steel bridge. JTG D64-2015. Beijing: China’s Ministry of Transport.
Gordo, J. M., and C. G. Soares. 2008. “Experimental evaluation of the behaviour of a mild steel box girder under bending moment.” Ships Offshore Struct. 3 (4): 347–358. https://doi.org/10.1080/17445300802370479.
Gordo, J. M., and C. G. Soares. 2014. “Experimental analysis of the effect of frame spacing variation on the ultimate bending moment of box girders.” Mar. Struct. 37: 111–134. https://doi.org/10.1016/j.marstruc.2014.03.003.
Guido, V. R. 1995. Python tutorial. Amsterdam. Netherlands: Centrum voor Wiskunde en Informatica.
Lan, X., J. Chen, T.-M. Chan, and B. Young. 2018. “The continuous strength method for the design of high strength steel tubular sections in compression.” Eng. Struct. 162 (5): 177–187. https://doi.org/10.1016/j.engstruct.2018.02.010.
Lan, X., J. Chen, T.-M. Chan, and B. Young. 2019. “The continuous strength method for the design of high strength steel tubular sections in bending.” J. Constr. Steel Res. 160: 499–509. https://doi.org/10.1016/j.jcsr.2019.05.037.
Liew, A., and L. Gardner. 2015. “Ultimate capacity of structural steel cross-sections under compression, bending and combined loading.” Structures 1: 2–11. https://doi.org/10.1016/j.istruc.2014.07.001.
Moolani, F. M. 1976. “Ultimate load behaviour of steel box girder stiffened compression flanges.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of London.
Nishihara, S. 1983. “Analysis of ultimate strength of stiffened rectangular plate (4th report)-on the ultimate bending moment of ship Hull Girder.” J. Soc. Nav. Archit. Jpn. 154: 367–375. https://doi.org/10.2534/jjasnaoe1968.1983.154_367.
Pavlovčič, L., B. Froschmeier, U. Kuhlmann, and D. Beg. 2010. “Slender thin-walled box columns subjected to compression and bending.” J. Civ. Eng. Manage. 16 (2): 179–188. https://doi.org/10.3846/jcem.2010.19.
Piculin, S., and P. Može. 2020. “Experimental and numerical analysis of stiffened curved plates as bottom flanges of steel bridges.” J. Constr. Steel Res. 164: 105822. https://doi.org/10.1016/j.jcsr.2019.105822.
Reckling, K. A. 1979. “Behaviour of box girders under bending and shear.” In Proc., 7th Int. Ship and Offshore Structures Congress, 46–49. Accessed December 25, 2019. http://www.cssrc.com/.
Saad-Eldeen, S., Y. Garbatov, and C. G. Soares. 2010. “Experimental assessment of the ultimate strength of a box girder subjected to four-point bending moment.” In Proc., 11th Int. Symp. on Practical Design of Ships and Other Floating Structures, 1134–1143. Rio de Janeiro, Brazil: Universidade Federal do Rio de Janeiro.
Seif, M., and B. W. Schafer. 2010. “Local buckling of structural steel shapes.” J. Constr. Steel Res. 66 (10): 1232–1247. https://doi.org/10.1016/j.jcsr.2010.03.015.
Shin, D. K., B. Van Dat, and K. Kim. 2014. “Compressive strength of HPS box girder flanges stiffened with open ribs.” J. Constr. Steel Res. 95: 230–241. https://doi.org/10.1016/j.jcsr.2013.12.014.
Sun, Y., and O. Zhao. 2019. “Material response and local stability of high-chromium stainless steel welded I-sections.” Eng. Struct. 178: 212–226. https://doi.org/10.1016/j.engstruct.2018.10.024.
Tse, K., J. Wang, and X. Yun. 2021. “Structural behaviour and continuous strength method design of high strength steel non-slender welded i-section beam-columns.” Thin-Walled Struct. 169 (3): 108273. https://doi.org/10.1016/j.tws.2021.108273.
Xiao, W. 2017. “Research on residual stress and stable bearing performance of stiffened plates in steel bridges.” [In Chinese.] Ph.D. thesis, Dept. of Bridge Engineering, Tongji Univ.
Xu, M. C., Z. J. Song, and J. Pan. 2017. “Study on influence of nonlinear finite element method models on ultimate bending moment for hull girder.” Thin-Walled Struct. 119: 282–295. https://doi.org/10.1016/j.tws.2017.06.009.
Yang, F., Y. Liu, and H. Xin. 2018. “Negative bending capacity prediction of composite girders based on continuous strength method.” Thin-Walled Struct. 129: 278–288. https://doi.org/10.1016/j.tws.2018.04.005.
Yun, X., and L. Gardner. 2017. “Stress–strain curves for hot-rolled steels.” J. Constr. Steel Res. 133: 36–46. https://doi.org/10.1016/j.jcsr.2017.01.024.
Zhao, O., S. Afshan, and L. Gardner. 2017a. “Structural response and continuous strength method design of slender stainless steel cross-sections.” Eng. Struct. 140 (6): 14–25. https://doi.org/10.1016/j.engstruct.2017.02.044.
Zhao, Q., B. Chen, Y. Chen, and Y. Peng. 2017b. “Experimental study on local stability of U-rib stiffened plate.” [In Chinese.] J. Build. Struct. 38 (7): 156–163.
Zhao, Q., Z. Zhai, and B. Chen. 2016. “Experimental study on compression stability of hybrid steel plate stiffened with U-ribs.” [In Chinese.] J. Build. Struct. 37 (7): 54–63.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Feb 25, 2021
Accepted: Mar 2, 2022
Published online: May 3, 2022
Published in print: Jul 1, 2022
Discussion open until: Oct 3, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Leroy Gardner, Xiang Yun, Fiona Walport, The Continuous Strength Method – Review and outlook, Engineering Structures, 10.1016/j.engstruct.2022.114924, 275, (114924), (2023).